《BS-EN-130100-1998.pdf》由会员分享,可在线阅读,更多相关《BS-EN-130100-1998.pdf(24页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 130100:1998 Harmonized system of quality assessment for electronic components Sectional specification: fixed polyethylene- terephthalate film dielectric metal foil capacitors for direct current The European Standard EN 130100:1997 has the status of a British Standard ICS 31.06
2、0.30 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 130100:1998 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes i
3、nto effect on 15 February 1998 BSI 05-1999 ISBN 0 580 29115 4 National foreword This British Standard is the English language version of EN 130100:1997 published by the European Electronic Components Committee (CECC) of the European Committee for Electrotechnical Standardization (CENELEC). It supers
4、edes BS CECC 30100:1986 which will be withdrawn on 1998-04-01. The UK participation in its preparation was entrusted by Technical Committee EPL/40, Capacitors and resistors for electronic equipment, to Subcomittee EPL/40/1, Capacitors and EMI suppression components for electronic equipment, which ha
5、s the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in
6、the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entit
7、led “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Complian
8、ce with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 19 and a back cover. This standard has been updated (see copyright date) and may have had
9、 amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 130100:1998 BSI 05-1999i Conten
10、ts Page National forewordInside front cover Foreword2 Text of EN 1301003 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EURO
11、PEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 130100 October 1997 ICSSupersedes CECC 30 100:1985 and its amendments Descriptors: English version Sectional Specification: Fixed polyethylene-terephtalate film dielectric metal foil capacitors for direct current This European Standard was approved by
12、 CENELEC on 1992-10-14. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national st
13、andards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and n
14、otified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland
15、 and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1997 CENELEC All rights of exploitation in any form and by an
16、y means reserved worldwide for CENELEC members. Ref. No. EN 130100:1997 E Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 130100:1997 BSI 05-1999 2 Foreword At the request of CLC/TC CECC/SC 40XA (former WG 3), the text of CECC 30 100:1985
17、, Issue 2, with its amendments A1 through A7 and document CECC(Secretariat)3061, was submitted to the formal vote for conversion into a European Standard. The text of the draft, together with the voting report, circulated as document CECC(Secretariat)3199, was approved as EN 130100 on 1992-10-14. Ba
18、sed on the positive voting results on prAB to EN 130800, assessment level EZ was accepted for introduction into EN 130100 on 1997-03-11. The following dates were fixed: Contents Page Foreword2 Section 1. General3 1.1Scope 3 1.2Normative references3 1.3Information to be given in a detail specificatio
19、n 3 1.4Terminology 4 1.5Marking 4 Section 2. Preferred ratings and characteristics5 2.1Preferred climatic categories 5 2.2Preferred values of ratings 5 Section 3. Quality assurance procedures6 3.1Primary stage of manufacture 6 3.2Structurally similar components 6 3.3Certified test records 6 3.4Quali
20、fication approval6 3.5Quality conformance inspection7 Section 4. Tests and measuring methods8 4.1Visual examination and check of dimensions8 4.2Electrical tests 8 4.3Robustness of terminations 10 4.4Resistance to soldering heat 10 4.5Solderability 10 4.6Rapid change of temperature 11 4.7Vibration 11
21、 4.8Bump 11 4.9Shock 12 4.10 Climatic sequence 12 4.11 Damp heat, steady state 13 4.12 Endurance 13 Annex A (normative) Test plans for qualification approval and quality conformance inspection 14 Annex B (normative) Test schedule for qualification approval17 Table 1 Test voltages8 Table 2 Insulation
22、 resistance8 Table 3 Correction factors9 Table 4 Characteristics at lower category temperature10 Table 5 Characteristics at upper category temperature10 Table 6 Degrees of severity11 Table 7 Preferred severities12 Table 8 Test conditions13 latest date by which the EN has to be implemented at nationa
23、l level by publication of an identical national standard or by endorsement(dop) 1998-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn(dow) 1998-04-01 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) B
24、SI EN 130100:1997 BSI 05-19993 Section 1. General 1.1 Scope This European Standard specifies requirements for fixed capacitors for direct current, with electrodes of thin metal foils and a polyethylene-terephthalate film dielectric. It specifies preferred ratings and characteristics and selects from
25、 EN 130000 the appropriate quality assessment procedures, tests and measuring methods and gives general performance requirements for this type of capacitor. Capacitors for direct connection to the supply mains to provide radio interference suppression are not included. 1.2 Normative references This
26、European Standard incorporates by dated or undated reference, provisions from other publicatons. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publicati
27、ons apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. ISO 3:1973, Preferred numbers Series of preferred numbers. IEC 60062:1974, Marking codes for resistors and capacitors. IEC 6006
28、3:1963, Preferred number series for resistors and capacitors. A1:1967, A2:1977. IEC 60068, Basic environmental testing procedures. EN 130000:1993, Generic specification: Fixed capacitors. IEC 60410:1973, Sampling plans and procedures for inspection by attributes. 1.3 Information to be given in a det
29、ail specification 1.3.1 General The detail specification shall be derived from the relevant blank detail specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, they sha
30、ll be listed in 1.9 of the detail specification and indicated in the test schedules, for example by an asterisk. NOTEThe information given in 1.3.1 may for convenience be presented in tabular form. The following information shall be given in each detail specification and the values quoted shall pref
31、erably be selected from those given in the appropriate clause of this sectional specification. 1.3.2 Outline drawing and dimensions The detail specification shall give an illustration of the capacitor as an aid to easy recognition and for comparison of the capacitor with others. Dimensions and their
32、 associated tolerances, which affect interchangeability and mounting, shall be given in the detail specification. All dimensions shall preferably be stated in millimetres. Normally the numerical values shall be given for the length, the width and height of the body and the wire spacing or for cylind
33、rical types the body diameter, and the length and diameter of the terminations. When necessary, for example when a number of case sizes are covered by a detail specification, the dimensions and their associated tolerances shall be placed in a table below the drawing. When the configuration is other
34、than described above, the detail specification shall state such dimensional information as will adequately describe the capacitor. When the capacitor is not designed for use on printed boards, this shall be clearly stated in the detail specification. 1.3.3 Mounting The detail specification shall spe
35、cify the method of mounting to be applied for the application of the vibration and the bump or shock tests. The design of the capacitor may be such that special mounting fixtures are required in its use. In this case the detail specification shall describe the mounting fixtures and they shall be use
36、d in the application of the vibration and bump or shock tests. NOTEIf recommendations for mounting for “normal” use are made, they shall be included in the detail specification under “1.8 Additional information (Not for inspection purposes)”. If they are included, a warning can be given that the ful
37、l vibration, bump and shock performance may not be available if mounting methods other than those specified in 1.1 of the detail specification are used. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 130100:1997 4 BSI 05-1999 1.3.4 Ratin
38、gs and characteristics The ratings and characteristics shall be in accordance with the relevant clauses of this specification, together with the following: a) Rated capacitance range See 2.2.1. NOTEWhen products approved to the detail specification may have different ranges, the following statement
39、should be added: “The range of values available in each voltage range is given in the Register of Approvals CECC 00200”. b) Particular characteristics Additional characteristics may be listed, when they are considered necessary to specify adequately the component for design and application purposes.
40、 1.3.5 Marking The detail specification shall specify the content of the marking on the capacitor and on the package. Deviations from 1.5 of this sectional specification, shall be specifically stated. 1.4 Definitions For the purposes of this standard the definitons given in EN 130000 apply, together
41、 with the following: 1.4.1 rated voltage the maximum d.c. voltage which may be applied continuously to a capacitor at the rated temperature NOTEThe sum of the d.c. voltage and the peak a.c. voltage applied to the capacitor shall not exceed the rated voltage. The value of the peak a.c. voltage shall
42、not exceed the following percentages of the rated voltage at the frequencies stated and shall not be greater than 280 V: unless otherwise specified in the detail specification. 1.5 Marking 1.5.1 The information given in the marking is normally selected from the following list; the relative importanc
43、e of each item is indicated by its position in the list: a) rated capacitance; b) rated voltage; (d.c. voltage may be indicated by the symbol _ or .); c) tolerance on rated capacitance; d) category voltage; e) year and month (or week) of manufacture; f) manufacturers name or trade mark; g) climatic
44、category; h) manufacturers type designation; i) reference to the detail specification. 1.5.2 The capacitor shall be clearly marked with a), b) and c) above and with as many as possible of the remaining items as is considered necessary. Any duplication of information in the marking on the capacitor s
45、hould be avoided. 1.5.3 The package containing the capacitor(s) shall be clearly marked with all the information listed in 1.5.1. 1.5.4 Any additional marking shall be so applied that no confusion can arise. 50 100 1 000 10 000 Hz: 20 % Hz: 15 % Hz:3 % Hz:1 % Licensed Copy: sheffieldun sheffieldun,
46、na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 130100:1997 BSI 05-19995 Section 2. Preferred ratings and characteristics 2.1 Preferred climatic categories The capacitors covered by this specification are classified into climatic categories according to the general rules given
47、in IEC 60068-1. The lower and upper category temperature and the duration of the damp heat steady state tests shall be chosen from the following: lower category temperature: 55 C, 40 C and 25 C; upper category temperature: + 85 C, + 100 C and + 125 C; duration of the damp heat, steady state test: 4,
48、 10, 21 and 56 days. The severities for the cold and dry heat tests are the lower and upper category temperatures respectively. 2.2 Preferred values of ratings 2.2.1 Rated capacitance (CR) Preferred values of rated capacitance are 1; 1,5; 2,2; 3,3; 4,7 and 6,8 and their decimal multiples. These valu
49、es conform to the E6 series of preferred values given in IEC 60063. If other values are required they shall preferably be chosen from the E12 series. 2.2.2 Tolerance on rated capacitance The preferred tolerances on the rated capacitance are 5 %, 10 % and 20 %. 2.2.3 Rated voltage (UR) The preferred values of rated voltage are 40; 63; 100; 160; 250 and their decimal multiples. These values conform to the basic series of preferred values R5 given in ISO 3. 2.2.4 Category voltage (UC) The category voltage is: 0,8 UR fo
链接地址:https://www.31doc.com/p-3739480.html