《BS-EN-13052-1-2001.pdf》由会员分享,可在线阅读,更多相关《BS-EN-13052-1-2001.pdf(24页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13052-1:2001 Influence of materials on water intended for human consumption Organic materials Determination of colour and turbidity of water in piping systems Part 1: Test method The European Standard EN 13052-1:2001 has the status of a British Standard ICS 13.060.20; 13.060.6
2、0; 23.040.01 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:10:02 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 13052-1:2001 This British Standard, having been prepared under the direction of the Health and Environm
3、ent Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 16 November 2001 BSI 16 November 2001 ISBN 0 580 38396 2 National foreword This British Standard is the official English language version of EN 13052-1:2001. The UK participa
4、tion in its preparation was entrusted to Technical Committee EH/6, Effects of materials on water quality, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement interna
5、tional or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to includ
6、e all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee an
7、y enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 21 and a
8、 back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:10:02 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUR
9、OPENNE EUROPISCHE NORM EN 13052-1 September 2001 ICS 13.060.20; 23.040.01 English version Influence of materials on water intended for human consumption Organic materials Determination of colour and turbidity of water in piping systems Part 1: Test method Influence des matriaux sur leau destine la c
10、onsommation humaine Matriaux organiques Evaluation de la couleur et de la turbinit de leau dans les rseaux de conduites Partie 1: Mthode dessai Einfluss von Werkstoffen auf Wasser fr den menschlichen Gebrauch Organische Werkstoffe Bestimmung von Frbung und Trbung von Wasser in Rohrleitungssystemen T
11、eil 1: Prfverfahren This European Standard was approved by CEN on 17 August 2001. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and
12、bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility
13、 of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, N
14、orway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CENAll rights of exploitation in any form and by any means reserved worldwi
15、de for CEN national Members. Ref. No. EN 13052-1:2001 E Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:10:02 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13052-1:2001 (E) 2 Contents Page Foreword .4 Introduction.5 1Scope .6 2Normative references6 3Terms and definitions.6 4Principle.8 5Re
16、agents8 5.1Disinfection reagents.8 5.2Waters to be used for testing 8 5.3Cleaning liquids for apparatus.9 6Apparatus.9 6.1Apparatus for migration assessment .9 6.2Apparatus for colour and turbidity assessment9 7Samples of product and test pieces 9 7.1General .9 7.2Surface-area-to-volume ratio (S/V)1
17、0 7.2.1General.10 7.2.2Pipes.10 7.2.3Fittings, ancillaries and joints.11 8Preparation of reagents and apparatus.11 8.1reference water .11 8.2Test water with chlorine content 11 8.3Disinfection treatment water11 8.4Cleaning of the apparatus .11 923 C test procedure12 9.1General .12 9.2Flushing.12 9.3
18、Stagnation.13 9.3.1 Stagnation with disinfection water13 9.4Prewashing13 9.4.1Flushing .13 9.4.2Rinsing.13 9.5Migration .13 10Elevated temperature test procedure 14 10.1General .14 10.2Flushing.14 10.3Stagnation.14 10.3.1Stagnation with disinfection water14 10.3.2Stagnation without disinfection wate
19、r.14 10.4Flushing.15 10.5Elevated temperature stagnation.15 10.6Rinsing 15 10.7Migration .15 11Determination of colour and turbidity15 12Expression of results16 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:10:02 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13052-1:2001 (E) 3 13Test rep
20、ort16 13.1General information.16 13.2The information on the product shall at least include:16 13.3Information on the procedure 17 13.4Test results17 Annex A (informative) Arrangement for flushing large diameters pipes.18 Annex B (informative) Schematic presentation of the test method.19 B.1Products
21、to be tested at (23 ? 2) C 20 B.2Products to be tested at elevated temperatures 21 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:10:02 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13052-1:2001 (E) 4 Foreword This European Standard has been prepared by Technical Committee CEN/TC 164, Wat
22、er supply, the Secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2002, and conflicting national standards shall be withdrawn at the latest by March 2002.
23、 This European Standard has been prepared by CEN/TC 164, Water supply, in co-operation with CEN/TC 155, Plastics piping systems and ducting systems, and consists of two parts: Part 1: Test method; Part 2: Interpretation of laboratory values relative to field-use conditions. This standard is Part 1.
24、It contains the two following annexes. Annex A, which is informative, describes an arrangement for flushing large diameter pipes. Annex B, which is informative, summarizes schematically the relationship between the various stages of the document. The material-dependent parameters and/or performance
25、requirements are incorporated into the Product Standards, for example the System Standards for plastics piping systems. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium,
26、Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:10:02 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13052-1:2001
27、 (E) 5 Introduction In respect of potential adverse effects on the quality of water intended for human consumption caused by the materials, it is recalled to mind that, while awaiting the adoption of verifiable European acceptance criteria, such as proposed in a future European Acceptance Scheme, na
28、tional regulations remain in force. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:10:02 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13052-1:2001 (E) 6 1Scope This standard specifies a method for determining the colour and turbidity of test waters after their contact with the organic ma
29、terials used in piping systems. The term “products” comprises pipes, fittings, ancillaries including their coatings and joints. The test method described in this standard is applicable to products to be used under various conditions for the transport of water intended for human consumption and raw w
30、ater used for the manufacture of water intended for human consumption. Coatings or protective layers on products which are not intended to be in contact with these types of water are not covered by this method. This standard specifies the test method comprising a set of procedures with and without a
31、 disinfection pretreatment and possible temperatures for the test waters. The use of the disinfection pretreatment and the choice of the test temperature are dependant on the relevant national regulations and/or the system or product standards. 2Normative references This European Standard incorporat
32、es by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European
33、 Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN ISO 7027:1999, Water quality Determination of turbidity (ISO 7027:1999). EN ISO 7393-2:2000, Water quality Determination of fre
34、e chlorine and totalchlorine Part 2: Colorimetric method using N, N-diethyl-1, 4-phenylenediamine for routine control purposes (ISO 7393-2:1985). EN ISO 7887:1994, Water quality Examination and determination of colour (ISO 7887:1994). 3Terms and definitions For the purpose of this standard the follo
35、wing terms and definitions apply: 3.1 colour optical property that causes the changing of the spectral composition of transmitted visible light measured at three wavelengths (see clause 3 of EN ISO 7887:1994) 3.2 turbidity reduction of transparency of a liquid caused by the presence of undissolved m
36、atter (see clause 3 of EN ISO 7027:1999 as a source of this definition) 3.3 reference water water complying with the following requirements without and with addition of 1 mg/l chlorine for colour: spectral absorption coefficient less than 0,1 m-1; for turbidity: FNU 0,1 Licensed Copy: sheffieldun sh
37、effieldun, na, Sun Oct 29 09:10:02 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13052-1:2001 (E) 7 3.4 test waters water used for testing purposes as described in 5.2.2 and 5.2.3 3.5 migration water test water (see 3.4) which has been in contact with a test piece under specified conditions 3.6 blan
38、k water test water (see 3.4) which has been kept at the same specified conditions as migration water but without contact with the test piece(s) 3.7 flushing water tapwater distributed by a public supplier 3.8 disinfection treatment water water containing chlorine as described in 5.1.2 3.9 fitting, a
39、ncillary complete functional unit made up of one or more components and materials, parts of which are in contact with drinking water, e.g. taps, valves, water filters 3.10 product a manufactured item, in its finished form 3.11 sample one or more units, or specified quantity, drawn from a batch or lo
40、t, selected at random for inspection, e.g. in a laboratory 3.12 specimen a single sample of a product, to be prepared to obtain a single test result 3.13 test piece the specimen or portion which is conditioned, treated or otherwise prepared to be tested to obtain a single test result Licensed Copy:
41、sheffieldun sheffieldun, na, Sun Oct 29 09:10:02 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13052-1:2001 (E) 8 4Principle Following a defined pretreatment procedure of flushing, stagnation with or without disinfection and then prewashing, the surface of the test pieces, exposed in practice to dri
42、nking water, is brought into contact with test waters. The migration procedure is carried out three times on the same test piece under specified conditions as follows: Test pieces are put in contact with chlorinated and unchlorinated waters for 72 h at 23 C, or put in contact with unchlorinated wate
43、r for 24 h at specified temperature in the range 60 C to 85 C. After this contact, the migration water is assessed for colour and turbidity. Additional information is given in the relevant product standard, system standards or in a future European Acceptance Scheme concerning: the temperature to be
44、used in the test; the need for a disinfection pretreatment; the need to carry out a 23 C test, using chlorinated water, for products being tested at elevated temperatures. 5Reagents 5.1Disinfection reagents 5.1.1 Sodium hypochlorite solution, prepared from a commercial solution of sodium hypochlorit
45、e (NaOCl) and having a known concentration of about 0,1 % by mass of free chlorine determined in accordance with EN ISO 7393-2:2000. This sodium hypochlorite solution is unstable and shall be prepared on the day of use. 5.1.2 Disinfection treatment water, shall consist of a batch of reference water
46、(see 5.3.3) with a free chlorine content of (50 ? 5) mg/l as Cl2 after addition of sodium hypochlorite solution (see 5.1.1). 5.2Waters to be used for testing 5.2.1 Reference water shall be without colour and turbidity. 5.2.2 Test water without chlorine content, shall consist of a batch of reference
47、water (see 5.3.3) used for contact with test piece(s)and preparation of the blank water. 5.2.3 Test water with chlorine content, shall consist of a batch of reference water (see 5.3.3) with a free chlorine content of (1 0,2) mg/l after addition of sodium hypochlorite solution (see 5.1). Licensed Cop
48、y: sheffieldun sheffieldun, na, Sun Oct 29 09:10:02 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13052-1:2001 (E) 9 5.3Cleaning liquids for apparatus biodegradable detergent; hydrochloric acid, 2 mol/l (analytical grade); nitric acid, 10 % or 1,5 mol/l ( analytical grade); hydrogen peroxide, 3 % vo
49、l/vol (analytical grade). 6Apparatus 6.1 Apparatus for migration assessment The following equipment shall be used: 6.1.1 Vessels, containers, connectors and stoppers, made of materials which do not affect the colour and turbidity assessment under the specified test conditions, such as glass, polytetrafluorethylene (PTFE) or stainless steel. NOTE The material PTFE should only be used when there is a small contact area with the test water. Thus PTFE is unsuitable for containers. 6.1.2 Equipment, capa
链接地址:https://www.31doc.com/p-3739517.html