《BS-EN-2143-1993.pdf》由会员分享,可在线阅读,更多相关《BS-EN-2143-1993.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2143:1993 Rivets, solid, universal head, in aluminium 1050A, inch based series The European Standard EN 2143:1992 has the status of a British Standard UDC 621.884.2-034.715:629.7 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:19:15 GMT+00:00 2006, U
2、ncontrolled Copy, (c) BSI BS EN 2143:1993 This British Standard, having been prepared under the direction of the Aerospace Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 February 1993 BSI 11-1999 The following BSI references relate to
3、 the work on this standard: Committee reference ACE/12 Draft for comment 89/79398 DC ISBN 0 580 21973 9 Cooperating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the follo
4、wing countries: AustriaOesterreichisches Normungsinstitut BelgiumInstitut belge de normalisation DenmarkDansk Standardiseringsraad FinlandSuomen Standardisoimisliito, r.y. FranceAssociation franaise de normalisation GermanyDeutsches Institut fr Normung e.V. GreeceHellenic Organization for Standardiz
5、ation IcelandTechnological Institute of Iceland IrelandNational Standards Authority of Ireland ItalyEnte Nazionale Italiano di Unificazione LuxembourgInspection du Travail et des Mines NetherlandsNederlands Normalisatie-instituut NorwayNorges Standardiseringsforbund PortugalInstituto Portugus da Qua
6、lidade SpainAsociacin Espaola de Normalizacin y Certificacin SwedenStandardiseringskommissionen i Sverige SwitzerlandAssociation suisse de normalisation United KingdomBritish Standards Institution Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Fr
7、i Nov 03 02:19:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2143:1993 BSI 11-1999i Contents Page Cooperating organizationsInside front cover National forewordii Foreword2 1Scope3 2Normative references3 3Required characteristics3 4Designation5 5Marking5 6Technical specification5 National annex
8、 NA (informative) Committees responsibleInside back cover National annex NB (informative) Cross-referencesInside back cover Figure 13 Table 14 Table 24 Table 35 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:19:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2143:1993 ii BSI 11-1999 N
9、ational foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN 2143:1992 Aerospace series Rivets, solid, universal head, in aluminium 1050A, inch based series, published by the European Committee for
10、Standardization (CEN). EN 2143:1992 was produced as a result of international discussions in which the United Kingdom took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applicati
11、on. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see
12、 copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:19:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2143 Nov
13、ember 1992 UDC 621.884.2-034.715:629.7 Descriptors: Aircraft industry, full rivet, round head rivet, aluminium, dimension, designation English version Aerospace series Rivets, solid, universal head, in aluminium 1050A, inch based series Srie arospatiale Rivets ordinaires, tte ronde aplatie, en alumi
14、nium 1050A, srie base inches Luft- und Raumfahrt Vollniete, mit Universalkopf, aus Aluminium 1050A, Inch-Reihe This European Standard was approved by CEN on 1992-11-16. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European S
15、tandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, Fren
16、ch, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, F
17、rance, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels
18、 1992 Copyright reserved to CEN members Ref. No. EN 2143:1992 E Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:19:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2143:1992 2 BSI 11-1999 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacture
19、rs (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this standard has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard s
20、hall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 1993, and conflicting national standards shall be withdrawn at the latest by May 1993. According to the CEN/CENELEC Internal Regulations, the following countries are bo
21、und to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:19:15 GMT+00:00 2006,
22、 Uncontrolled Copy, (c) BSI EN 2143:1992 BSI 11-19993 1 Scope This standard specifies the characteristics of solid rivets, with universal head, inch based series, in aluminium for maximum operating temperature 120 C. 2 Normative references This European Standard incorporates by dated or undated refe
23、rence, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorpor
24、ated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 2000, Aerospace series Quality assurance EN aerospace products Approval of the quality system of manufacturers. EN 2114, Aerospace series Aluminium 1050A-H14 wire for solid rivet
25、s D k 10 mm1). EN 2345, Aluminium and aluminium alloy rivets Technical specification Aerospace series1). EN 2424, Aerospace series Identification marking of standard fasteners1). 3 Required characteristics 3.1 Configuration Dimensions Masses See Figure 1 and Table 1 and Table 2. Dimensions and toler
26、ances are expressed in millimetres. 3.2 Material EN 2114 The rivet shall be delivered in H14 condition. 1) Published as AECMA standard at the date of publication of the present standard Figure 1 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:19:15 GMT+00:00 2006, Uncontrolled Copy, (c) BS
27、I EN 2143:1992 4 BSI 11-1999 Table 1 Table 2 Diameter code D1aD2D3L2L3R1R2 max.min.max.min.max.min. 0.08 0161,651,553,353,051,61,20,72 0242,452,3554,52,41,811,452,90,15 0323,253,156,763,22,41,43,9 a D 1 max. may increase by 0,03, over length L3. Diameter code016024032 Length Massa kg/1 000 pieces Co
28、de L1 00440,0300,0740,149 00550,0360,0870,172 00660,0420,1000,194 00770,0470,1130,217 00880,0530,1250,239 00990,0590,1380,262 010100,0640,1500,284 011110,0700,1630,307 012120,0750,1760,329 014140,0870,2010,374 016160,1000,2250,419 018180,2500,465 020200,2750,510 022220,3010,555 024240,3260,600 02626
29、0,3510,645 028280,3770,691 030300,4020,736 032320,4270,781 035350,4660,849 040400,960 a Approximate values, calculated on the basis of 2,76 kg/dm3, given for information purpose only +0,2 0 +0,5 0 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:19:15 GMT+00:00 2006, Uncontrolled Copy, (c)
30、BSI EN 2143:1992 BSI 11-19995 4 Designation NOTEIf necessary, the originator code I9005 shall be placed between the description block and the identity block. 5 Marking 5.1 Rivet identification EN 2424, style G 5.2 Material identification See Table 3. Table 3 6 Technical specification EN 2345 except
31、for approval of manufacturers, see EN 2000. ColourCode None- (hyphen) RedF The method of achieving is at the manufacturers option. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:19:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 6 blank Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03
32、 02:19:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2143:1993 BSI 11-1999 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committ
33、ee ACE/12, upon which the following bodies were represented: Association of Electronics, Telecommunications and Business Equipment Industries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companies Ltd. National annex NB (informative) Cross-references The B
34、ritish Standards corresponding to the European Standards referred to in the text are identical in number and title with those given in clause 2, with the exception of EN 2114, EN 2345 and EN 2424 for which no corresponding British Standards exist. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov
35、03 02:19:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2143:1993 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international
36、level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would b
37、e grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating
38、 service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders fo
39、r international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and
40、 its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developm
41、ents and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publicat
42、ions of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permiss
43、ion from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:19:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI
链接地址:https://www.31doc.com/p-3739825.html