《BS-EN-13422-2004.pdf》由会员分享,可在线阅读,更多相关《BS-EN-13422-2004.pdf(50页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13422:2004 Vertical road signs Portable deformable warning devices and delineators Portable road traffic signs Cones and cylinders The European Standard EN 13422:2004 has the status of a British Standard ICS 93.080.30 ? Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12
2、:27:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 13422:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 4 November 2004 BSI 4 November 2004 ISBN 0 580 44726 X National foreword This British Standard is the official English language
3、 version of EN 13422:2004. It supersedes BS 873-8:1985 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee B/509, Road equipment, to Subcommittee B/509/3, Construction of road traffic signs, which has the responsibility to: A list of organizations represe
4、nted on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index
5、”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confe
6、r immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgat
7、e them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 46, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publicati
8、on Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:27:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13422 October 2004 ICS 93.080.30 English version Vertical road signs - Portable deformable warning devices and deli
9、neators - Portable road traffic signs - Cones and cylinders Signalisation routire verticale - Signaux temporaires - Dispositifs coniques et balises de signalisation Straenverkehrszeichen (vertikal) - Transportable Straenverkehrszeichen - Leitkegel und Leitzylinder This European Standard was approved
10、 by CEN on 24 June 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand
11、ards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to
12、the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, No
13、rway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any form and by
14、 any means reserved worldwide for CEN national Members. Ref. No. EN 13422:2004: E Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:27:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13422:2004 (E) 2 Contents page Foreword.4 1 Scope6 2 Normative references .6 3 Terms, definitions, symbols a
15、nd abbreviations 6 4 Design, dimensions and tolerances9 4.1 Traffic cones9 4.1.1 Design of traffic cones .9 4.1.2 Dimensions of traffic cones.9 4.2 Traffic cylinders 10 4.2.1 Design of traffic cylinders10 4.2.2 Design of traffic cylinders10 4.3 Tolerances .10 5 Materials.11 6 Performance requirement
16、s 11 6.1 Visual performance.11 6.1.1 Classification.11 6.1.2 Colour; luminance factor and retroreflective requirements.11 6.2 Physical performance.14 6.2.1 Stability of traffic cones .14 6.2.2 Drop resistance of traffic cones15 6.2.3 Adhesion of retroreflective surfaces 15 6.2.4 Continuity of retror
17、eflective surfaces.15 6.2.5 Resistance to damage at low temperatures.15 6.2.6 Resistance to bending - traffic cylinders15 6.2.7 Resistance to fatigue of traffic cylinders15 7 Methods of tests16 7.1 General requirements and records.16 7.2 Determination of chromaticity and luminance factor in dry cond
18、itions 16 7.3 Photometric tests16 7.3.1 Determination of minimum initial coefficient of retroreflection R 16 7.3.2 Determination of coefficient of retroreflective performance R for retroreflective traffic cones or traffic cylinders 16 7.3.3 Determination of relative distribution of retroreflective p
19、erformance 17 7.4 Test for determination of stability of traffic cones20 7.5 Low temperature impact resistance test20 7.6 Drop test for traffic cones21 7.7 Measurement of coefficient of retroreflection of wet retroreflective surfaces.22 7.7.1 Principle.22 7.7.2 Apparatus 22 7.7.3 Method23 7.7.4 Repo
20、rt.23 7.8 Test for adhesion of retroreflective surface(s) of traffic cones and traffic cylinders23 7.9 Bending test for traffic cylinders.23 7.9.1 Apparatus 23 7.9.2 Test method.23 7.10 Fatigue test for traffic cylinders 24 7.10.1 Apparatus 24 Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 1
21、2:27:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13422:2004 (E) 3 7.10.2 Test method.24 8 Marking 26 8.1 Traffic cones26 8.1.1 Base plate 26 8.1.2 Cone body26 8.1.3 Retroreflective surfaces (Traffic cones of all types of construction)26 8.2 Traffic cylinders 26 8.2.1 Cylinder Body (in any conve
22、nient visible position) 26 8.2.2 Retroreflective surfaces.27 8.3 Legibility and durability of markings 27 8.3.1 Size of lettering (height).27 8.3.2 Durability of marking27 8.4 Examples of marking scheme .27 8.4.1 Traffic cones27 8.4.2 Traffic cylinders 27 8.5 Anti-theft markings.28 9 Evaluation of c
23、onformity28 9.1 Initial type testing28 9.2 Factory production control34 9.3 Common requirements.36 9.3.1 General.36 Annex A (normative) Technical documentation for ITT.37 Annex B (informative) Examples of test forms to register the results of a conformity review.38 Annex C (informative) Environmenta
24、l considerations.45 Bibliography .46 Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:27:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13422:2004 (E) 4 Foreword This document (EN 13422:2004) has been prepared by the Technical Committee CEN/TC 226 “Road Equipment“ the Secretariat of which
25、 is held by AFNOR. No existing document is superseded. It derives from performance requirements and test methods published in CEN, CENELEC, CIE and ISO documents together with standards of the CEN member organisations. This European Standard shall be given the status of a national standard, either b
26、y publication of an identical text or by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by April 2005. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implem
27、ent this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
28、Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:27:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13422:2004 (E) 5 Introduction This document may be used to implement type approval and certification testing. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:27:42 GMT+00:00 2006,
29、Uncontrolled Copy, (c) BSI EN 13422:2004 (E) 6 1 Scope This document specifies requirements for new traffic cones and new traffic cylinders with retroreflective properties. This document specifies minimum essential visual and physical performance characteristics; test methods for determination of pr
30、oduct performance and the means by which this performance may be communicated to the user and the public including safety enforcement agencies. The document provides a series of categories or classes by which a traffic cone or traffic cylinder may be specified for use in different applications in ac
31、cordance with best practice. In the case of physical properties, performance levels and indicative tests are provided for cold weather, stability, and impact resistance when dropped. Requirements for visual recognition properties, colour, retroreflectivity and luminance are provided. All of the test
32、s contained in this document already exist in one or more national technical standard(s) of Member State(s), or in legislative requirement(s) or code(s) of practice of Member State(s). Provision for identification and marking to declared levels of performance is provided. There are other product sha
33、pes which perform similar functions. This document does not cover devices made in other shapes, or which do not meet the design requirements of this document. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only
34、the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12767, Passive safety of support structures for road equipment - Requirements and test methods EN ISO/IEC17025, General requirements for the competence of testing a
35、nd calibration laboratories (ISO/IEC 17025:1999). ISO 4:1997, Information and documentation Rules for the abbreviation of title words and titles of publications. CIE 15.2:1986, Colorimetry. CIE 17.4:1987, International lighting vocabulary. CIE 54.2:2001, Retroreflection Definition and measurement. 3
36、 Terms, definitions, symbols and abbreviations For the purposes of this document, the following terms and definitions together with the symbols and abbreviations given in ISO 4:1997 apply. The photometric definitions given in CIE 17.4:1997 together with the following apply. 3.1 traffic cone three di
37、mensional device of conical shape comprising one or more parts including a base plate, cone body and a retroreflective surface or surfaces Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:27:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13422:2004 (E) 7 3.2 base plate lowest part of the
38、traffic cone which supports the cone body, having an upper visible surface, and a lower surface in contact with the support surface 3.3 cone body part of the traffic cone which is conical in shape, but excludes the base plate and the retroreflective surface(s) 3.4 category A cone traffic cone which
39、is totally retroreflective, except for the base plate 3.5 category B cone traffic cone in which only a part or parts of the cone body are retroreflective 3.6 traffic cylinder three dimensional device of substantially cylindrical shape comprising one or more parts including a cylinder body, and a ret
40、roreflective surface or surfaces 3.7 cylinder body part of the traffic cylinder which is substantially cylindrical in shape and supports the retroreflective surface or surfaces 3.8 category A cylinder traffic cylinder which is totally retroreflective 3.9 category B cylinder traffic cylinder in which
41、 only part or parts of the cylinder body are retroreflective 3.10 retroreflective surface(s) part (or those parts) of a traffic cone or traffic cylinder fixed to the cone body or cylinder body which are retroreflective according to the requirements of this document Licensed Copy: sheffieldun sheffie
42、ldun, na, Mon Oct 30 12:27:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13422:2004 (E) 8 3.11 height (H) traffic Cone - the vertical distance between the support surface and the top of the traffic cone traffic Cylinder - the vertical distance between the top of the cylinder body and the lowest e
43、xtremity of the cylinder body 3.12 batch amount of product manufactured as one complete operation as defined by the manufacturer in its FPC system manual and accepted by the notified body 3.13 production identification code code that will be defined by the manufacturer of the retroreflective sheetin
44、g in order to achieve traceability 3.14 test product product in original size and design, or part of it, prepared by the manufacturer and submitted to the ITT procedure 3.15 sample construction representing parts of the product or its constituents in original materials prepared by the manufacturer a
45、nd submitted to the ITT procedure 3.16 reference sample sample as defined in 3.3 to be retained in order to be able to repeat the ITT procedure in case of disagreements 3.17 manufacturer responsible body in the framework of this document 3.18 supplier producer of components for use in the product 3.
46、19 product families products that are related in such a way that testing of one of the products covers all of the products from a product family 3.20 notified body body responsible for the third party execution of ITT in the framework of this document Licensed Copy: sheffieldun sheffieldun, na, Mon
47、Oct 30 12:27:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13422:2004 (E) 9 4 Design, dimensions and tolerances 4.1 Traffic cones 4.1.1 Design of traffic cones 4.1.1.1 Shape of traffic cones There shall be 2 shape classes for traffic cones (S1 and S2). Class S1 - The angle between the sides of th
48、e cone body and the cones vertical axis shall be (10 2,5) for at least the uppermost 75 % H of the traffic cone. The lower 25 % H of the traffic cone above the base plate may have an increased angle between the sides of the body and the traffic cones vertical axis of between 7,5 and 14,5. Class S2 -
49、 The angle between the sides of the cone body and the cones vertical axis shall be (10 2,5) for at least the uppermost 75 % H of the traffic cone. The lower 25 % H of the traffic cone above the base plate may have an increased angle between the sides of the body and the traffic cones vertical axis of between 7,5 and 45. 4.1.1.2 Shape of base plate for traffic cones The base plate shall have a minimum of 4 and not more than 8 sides. 4.1.2 Dimensions of traffic cones 4.1.2
链接地址:https://www.31doc.com/p-3739843.html