《BS-EN-1380-2009.pdf》由会员分享,可在线阅读,更多相关《BS-EN-1380-2009.pdf(18页珍藏版)》请在三一文库上搜索。
1、BS EN 1380:2009 ICS 91.080.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Timber structures Test methods Load bearing nails, screws, dowels and bolts Licensed CopyChinese University of Hong Kong, 13/06/2009 05:18, Uncontrolled Copy, (c) BSI This British St
2、andard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2009 BSI 2009 ISBN 978 0 580 56920 3 Amendments/corrigenda issued since publication DateComments BS EN 1380:2009 National foreword This British Standard is the UK implementation of EN 1380:2009. It su
3、persedes BS EN 1380:1999 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee B/518, Structural timber. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the
4、necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Licensed CopyChinese University of Hong Kong, 13/06/2009 05:18, Uncontrolled Copy, (c) BSI BS EN 1380:2009 EUROPEAN STANDARD NORME
5、EUROPENNE EUROPISCHE NORM EN 1380 April 2009 ICS 91.080.20Supersedes EN 1380:1999 English Version Timber structures - Test methods - Load bearing nails, screws, dowels and bolts Structures en bois - Mthode dessai - Pointes, tire-fonds, broches et boulons porteurs Holzbauwerke - Prfverfahren - Tragen
6、de Nagelverbindungen This European Standard was approved by CEN on 2 November 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists an
7、d bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsi
8、bility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Icela
9、nd, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue
10、Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1380:2009: E Licensed CopyChinese University of Hong Kong, 13/06/2009 05:18, Uncontrolled Copy, (c) BSI BS EN 1380:2009 EN 1380:2009 (E) 2 Contents Page
11、 Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .5 4 Symbols and abbreviations 5 5 Requirements .5 5.1 Timber .5 5.2 Wood-based products .5 5.3 Metal plates and dowel type fasteners 5 6 Test methods 6 6.1 General 6 6.2 Conditioning .6 6.3 Fabrication of the test pieces .6 6.4
12、Preparation of the test pieces 6 6.4.1 Load parallel to grain 6 6.4.2 Load perpendicular to grain .9 6.4.3 Determination of relative displacements . 14 6.5 Test procedure 14 6.6 Test results 14 6.7 Test report . 14 Licensed CopyChinese University of Hong Kong, 13/06/2009 05:18, Uncontrolled Copy, (c
13、) BSI BS EN 1380:2009 EN 1380:2009 (E) 3 Foreword This document (EN 1380:2009) has been prepared by Technical Committee CEN/TC 124 “Timber structures”, the secretariat of which is held by SFS. This European Standard shall be given the status of a national standard, either by publication of an identi
14、cal text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by October 2009. This document supersedes EN 1380:1999. The first version of this European Standard was published in September 1999 and considered only connections with nail
15、s. When the product standard for dowel type fasteners EN 14592 became available the scope of EN 1380 was expanded. Therefore, this revised version covers dowel type fasteners as nails, screws, dowels and bolts. Connections with load bearing staples are considered in EN 1381:1999. According to the CE
16、N/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
17、Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed CopyChinese University of Hong Kong, 13/06/2009 05:18, Uncontrolled Copy, (c) BSI BS EN 1380:2009 EN 1380:2009 (E) 4 1 Scope This European Standard specifies
18、 test methods for determining the strength and deformation characteristics of laterally loaded connections with nail, screws, dowels and bolts in load-bearing timber structures. The methods assess connections with members of timber (solid timber or glued laminated timber) or wood-based products or m
19、etal plates (but not punched metal plate fasteners) in the combination proposed for use in service. The methods are used to determine load-slip characteristics and maximum load of connections where various angles between the applied force and the timber grain direction, or the main direction of the
20、wood-based products, respectively, are possible. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including an
21、y amendments) applies. EN 322, Wood-based panels Determination of moisture content EN 323, Wood-based panels Determination of density EN 13183-2, Moisture content of a piece of sawn timber Part 2: Estimation by electrical resistance method EN 14080, Timber structures Glued laminated timber Requireme
22、nts EN 14081-1, Timber structures Strength graded structural timber with rectangular cross section Part 1: General requirements EN 14358, Timber structures Calculation of characteristic 5-percentile values and acceptance criteria for a sample EN 14592, Timber structures Dowel-type fasteners Requirem
23、ents EN 26891:1991, Timber structures Joints made with mechanical fasteners General principles for the determination of strength and deformation characteristics (ISO 6891:1983) EN 28970, Timber structures Testing of joints made with mechanical fasteners Requirements for wood density (ISO 8970:1989)
24、ISO 3131, Wood Determination of density for physical and mechanical tests Licensed CopyChinese University of Hong Kong, 13/06/2009 05:18, Uncontrolled Copy, (c) BSI BS EN 1380:2009 EN 1380:2009 (E) 5 3 Terms and definitions For the purposes of this document, the following terms and definitions apply
25、. 3.1 deformation of the connection mean value of the measurements of the relative displacements of the members 3.2 dowel type fasteners elements such as nails, screws, dowels and bolts as defined by EN 14592 4 Symbols and abbreviations For the purposes of this document, the following symbols and ab
26、breviations apply. b width of member cross-section, in millimetres F load, in newtons t member thickness, in millimetres 5 Requirements 5.1 Timber The timber (solid timber or glued laminated timber) shall satisfy the requirements of EN 14080, EN 14081-1 and shall be selected in accordance with eithe
27、r of the methods given in EN 28970. For each test piece, the individual members to be joined shall be selected to ensure a test piece of balanced density. For a group of similar test pieces, separate planks shall be used for each test piece. NOTE The members should be free from major defects, which
28、could lead to premature failure in the area away from the fasteners. 5.2 Wood-based products The specification of the wood based products shall be established. The products used for the individual members of the test pieces shall be representative of the class or range of product to which they belon
29、g and the relevant properties shall be declared. One unique grade shall be used to make the test pieces. For each test piece, the individual members in the connection shall be selected from separate pieces of material. 5.3 Metal plates and dowel type fasteners The specification of the metal plates s
30、hall be established. The requirements for dowel type fasteners as given in EN 14592 apply. Licensed CopyChinese University of Hong Kong, 13/06/2009 05:18, Uncontrolled Copy, (c) BSI BS EN 1380:2009 EN 1380:2009 (E) 6 6 Test methods 6.1 General The moisture content and density of the timber or wood-b
31、ased products members at test shall be determined as specified in EN 13183-2, ISO 3131, EN 322 and EN 323 as appropriate. 6.2 Conditioning The test pieces shall be manufactured with the timber or wood-based products at an equilibrium moisture content corresponding to (20 2) C and (85 5) % relative h
32、umidity. The material is conditioned when it attains constant mass. Constant mass is considered to be attained when the results of two successive weightings, carried out at an interval of 6 h, do not differ by more than 0,1 % of the mass of the material. After manufacture but prior to testing the te
33、st pieces shall be stored for at least one week at (20 2) C and (65 5) % relative humidity. For certain investigations other moisture conditioning can be appropriate, and shall be reported. NOTE For some hardwoods a much longer storing period can be necessary or the test pieces should be made with a
34、ppropriate gaps between the members. 6.3 Fabrication of the test pieces If there are no special requirements, timber members shall be planed. Test pieces shall be fabricated with the fasteners perpendicular to the member surface. The insertion of the dowel type fasteners shall follow normal preparat
35、ion (e.g. pre-boring) and practice, which shall be reported. The number of fasteners shall reflect the actual use in practice. In principle the connection is symmetrical with respect to the direction of the load comprising the geometry of the timber members and number and penetration depth of the fa
36、steners. For nails and screws the depth of the fastener head indentation will have an influence on the test result, particularly for connections loaded in double shear. Therefore, if the fabrication technique permits the fastener heads shall protrude above the surface. 6.4 Preparation of the test pi
37、eces 6.4.1 Load parallel to grain For connections with fasteners that do not pass fully through all members: - consisting solely of timber or wood-based products (or combinations thereof) the test pieces shall be fabricated either as a) three-member connections with dowel type fasteners from each si
38、de, loaded in single shear, see Figure 1, or b) three-member connections with dowel type fasteners from each side, loaded in double shear, see Figure 2. The minimum end length l is 50 mm as shown in Figures 1 and 2 may not be appropriate to thin timber or wood- based products subjected to compressio
39、n loads. - with metal plates connected with dowel type fasteners to timber or wood-based products members, the test pieces shall be fabricated either as Licensed CopyChinese University of Hong Kong, 13/06/2009 05:18, Uncontrolled Copy, (c) BSI BS EN 1380:2009 EN 1380:2009 (E) 7 a) single shear test
40、pieces with dowel type fasteners from each side and with the side members of metal plates, or b) double shear test pieces with dowel type fasteners from each side and with the metal plate as central member. Licensed CopyChinese University of Hong Kong, 13/06/2009 05:18, Uncontrolled Copy, (c) BSI BS
41、 EN 1380:2009 EN 1380:2009 (E) 8 Key 1 grain direction 2 not protruding end 3 protruding end 4 displacement pick-up points l free length t1 side member width t2 middle member NOTE Dowels and bolts will usually protrude at the outer faces of the side members. Figure 1 Example of a three timber member
42、 connection with not fully penetrating dowel type fasteners loaded in single shear and with the positions of displacement pick up points Licensed CopyChinese University of Hong Kong, 13/06/2009 05:18, Uncontrolled Copy, (c) BSI BS EN 1380:2009 EN 1380:2009 (E) 9 Key 1 grain direction 2 not protrudin
43、g end 3 protruding end 4 displacement pick-up points l free length t1 side member width t2 middle member NOTE Dowels and bolts will usually protrude at the outer faces of the side members. Figure 2 Example of a three timber member connection with not fully penetrating dowel type fasteners, loaded in
44、 double shear and with the position of displacement pick up points 6.4.2 Load perpendicular to grain For connections with fasteners that do not fully pass through all members: - consisting solely of timber or wood-based products (or combinations thereof) the test pieces shall be fabricated either as
45、 a) three-member connections with dowel type fasteners from each side, loaded in single shear, see Figures 3 and 4, or b) three-member connections with dowel type fasteners from each side, loaded in double shear, see Figures 5 and 6. Licensed CopyChinese University of Hong Kong, 13/06/2009 05:18, Un
46、controlled Copy, (c) BSI BS EN 1380:2009 EN 1380:2009 (E) 10 The minimum end length l = 50 mm as shown in Figures 3 to 6 may not be appropriate to thin timber or wood-based products subjected to compression loads. Key 1 grain direction 2 not protruding end 3 protruding end 4 displacement pick-up poi
47、nts l free length t1 side member width t2 middle member Figure 3 Example of a three timber member connection with not fully penetrating dowel type fasteners loaded single shear, side members loaded perpendicular to grain and with the positions of displacement pick up points Licensed CopyChinese Univ
48、ersity of Hong Kong, 13/06/2009 05:18, Uncontrolled Copy, (c) BSI BS EN 1380:2009 EN 1380:2009 (E) 11 Key 1 grain direction 2 not protruding end 3 protruding end 4 displacement pick-up points l free length t1 side member width t2 middle member Figure 4 Example of a three timber member connection wit
49、h not fully penetrating dowel type fasteners loaded single shear with a central member loaded perpendicular to grain and the position of displacement pick up points - with metal plates to timber or wood based products members, the test pieces shall be fabricated either as a) single shear test pieces with dowel type fasteners from each side and with the side members of metal plates, or Licensed CopyChinese University of Hong Kong, 13/06/2009 05:18, Uncontrolled Copy, (c) BSI BS EN 1380:2009 EN 1380:2009 (E) 12 b) double
链接地址:https://www.31doc.com/p-3739851.html