BS-EN-1870-13-2007.pdf
《BS-EN-1870-13-2007.pdf》由会员分享,可在线阅读,更多相关《BS-EN-1870-13-2007.pdf(70页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1870-13:2007 Incorporating corrigendum June 2008 Safety of woodworking machines Circular sawing machines Part 13: Horizontal beam panel sawing machines ICS 79.120.10 ? Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=B
2、oeing Co/5910770001 Not for Resale, 08/14/2008 20:21:52 MDTNo reproduction or networking permitted without license from IHS -,-,- BS EN 1870-13:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2008 BSI 2008 ISBN 978 0 580 61968
3、 7 National foreword This British Standard is the UK implementation of EN 1870-13:2007. Together with BS EN 1870-14:2007, it supersedes BS EN 1870-2:1999 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MTE/23, Woodworking machines. A list of organizat
4、ions represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations
5、. Amendments/corrigenda issued since publication DateComments 30 June 2008Supersession details updated in national foreword Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:21:52 MDTNo repro
6、duction or networking permitted without license from IHS -,-,- EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1870-13 December 2007 ICS 79.120.10Supersedes EN 1870-2:1999 English Version Safety of woodworking machines - Circular sawing machines - Part 13: Horizontal beam panel sawing machines
7、Scurit des machines pour le travail du bois - Machines scier circulaires - Partie 13: Scies panneaux horizontales presseur Sicherheit von Holzbearbeitungsmaschinen - Kreissgemaschinen - Teil 13: Horizontale Plattenkreissgemaschinen mit Druckbalken This European Standard was approved by CEN on 21 Oct
8、ober 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be ob
9、tained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Mana
10、gement Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, No
11、rway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any fo
12、rm and by any means reserved worldwide for CEN national Members. Ref. No. EN 1870-13:2007: E Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:21:52 MDTNo reproduction or networking permitted
13、 without license from IHS -,-,- EN 1870-13:2007 (E) 2 Contents Page Foreword4 Introduction.6 1 Scope 7 2 Normative references8 3 Terms and definitions .10 4 List of significant hazards 18 5 Safety requirements and / or measures 21 5.1 General21 5.2 Controls 21 5.2.1 Safety and reliability of control
14、 systems.21 5.2.2 Position of controls.23 5.2.3 Starting .23 5.2.4 Normal stopping 24 5.2.5 Emergency stop.25 5.2.6 Pressure beam control26 5.2.7 Speed changing.26 5.2.8 Failure of the power supply26 5.2.9 Failure of the control circuits.27 5.3 Protection against mechanical hazards27 5.3.1 Stability
15、.27 5.3.2 Hazard resulting from break-up during operation27 5.3.3 Tool holder and tool design28 5.3.4 Braking29 5.3.5 Workpiece supports and guides29 5.3.6 Prevention of access to moving parts.31 5.3.7 Guarding of drives.42 5.4 Protection against non-mechanical hazards 43 5.4.1 Fire 43 5.4.2 Noise .
16、43 5.4.3 Emission of chips and dust44 5.4.4 Electricity45 5.4.5 Ergonomics and handling.45 5.4.6 Pneumatics.46 5.4.7 Electromagnetic compatibility46 5.4.8 Static electricity .46 5.4.9 Errors of fitting.46 5.4.10 Laser .46 5.4.11 Supply disconnection (isolation).47 5.4.12 Maintenance.47 6 Information
17、 for use47 6.1 Warning devices 47 6.2 Marking.48 6.3 Instruction handbook49 Annex A (informative) Use of well tried components53 Annex B (normative) Impact test method for guards54 B.1 General54 B.2 Test method54 BS EN 1870-13:2007 Copyright British Standards Institution Provided by IHS under licens
18、e with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:21:52 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 1870-13:2007 (E) 3 B.2.1 Preliminary remarks54 B.2.2 Testing equipment.54 B.2.3 Projectile for guards54 B.2.4 Sampling.54 B.2.
19、5 Test procedure.54 B.3 Results55 B.4 Assessment .55 B.5 Test report55 B.6 Test equipment for impact test55 Annex C (normative) Saw spindle dimensional tolerances57 Annex D (normative) Rigidity test for sectional safety curtain material.58 Annex E (normative) Braking tests.60 E.1 Conditions for all
20、tests60 E.2 Tests .60 E.2.1 Un-braked run-down time.60 E.2.2 Braked run-down time.60 Annex F (normative) Use of electronic components 61 F.1 General .61 F.2 SRECS design61 F.2.1 Components, hardware.61 F.2.2 Safety related software.62 Annex ZA (informative) Relationship between this European Standar
21、d and the Essential Requirements of EU Directive 98/37/EC64 Bibliography67 BS EN 1870-13:2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:21:52 MDTNo reproduction or networking permitte
22、d without license from IHS -,-,- EN 1870-13:2007 (E) 4 Foreword This document (EN 1870-13:2007) has been prepared by Technical Committee CEN/TC 142 “Woodworking machines - Safety”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, eithe
23、r by publication of an identical text or by endorsement, at the latest by June 2008, and conflicting national standards shall be withdrawn at the latest by June 2009. This document together with prEN 1870-14:2007 supersedes EN 1870-2:1999. This document has been prepared under a mandate given to CEN
24、 by the European Commission and the European Free Trade Association, and supports essential requirements of the Machinery Directive. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. Organisations contributing to the preparation of this Europea
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 1870 13 2007
链接地址:https://www.31doc.com/p-3739859.html