BS-EN-13749-2005.pdf
《BS-EN-13749-2005.pdf》由会员分享,可在线阅读,更多相关《BS-EN-13749-2005.pdf(50页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13749:2005 Railway applications Methods of specifying structural requirements of bogie frames The European Standard EN 13749:2005 has the status of a British Standard ICS 45.040 ? BS EN 13749:2005 This British Standard was published under the authority of the Standards Policy
2、and Strategy Committee on 28 April 2005 BSI 28 April 2005 ISBN 0 580 45948 9 National foreword This British Standard is the official English language version of EN 13749:2005. The UK participation in its preparation was entrusted by Technical Committee RAE/3, Railway rolling stock material, to Subco
3、mmittee RAE/3/-/3, Bogie frames, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be fo
4、und in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are res
5、ponsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep
6、 the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 46, an inside back cover and a back cover. The BSI copyright notice displaye
7、d in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13749 April 2005 ICS 45.040 English version Railway applications - Methods of specifying structural requirements of bogie fra
8、mes Applications ferroviaires - Essieux monts et bogies - Mthode pour spcifier les exigences en matire de rsistance des structures de chssis de bogie Bahnanwendungen - Radstze und Drehgestelle - Spezifikationsverfahren fr Festigkeitsanforderungen an Drehgestellrahmen This European Standard was appro
9、ved by CEN on 3 November 2003. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
10、 standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notifi
11、ed to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlan
12、ds, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2005 CENAll rights of exploitation in any form
13、and by any means reserved worldwide for CEN national Members. Ref. No. EN 13749:2005: E EN 13749:2005 (E) 2 Contents page Foreword. 5 1 Scope 6 2 Normative references . 6 3 Terms and definitions. 6 3.1 Commercial terms. 6 3.2 Technical terms. 6 3.3 Symbols and units 8 4 Co-ordinate system. 9 5 Class
14、ification. 10 6 Responsibilities. 11 7 Contents of technical specification 11 7.1 Scope 11 7.2 General requirements. 11 7.3 Vehicle conditions and interfaces. 11 7.4 Operational characteristics 12 7.5 Line characteristics 12 7.6 Environmental conditions 12 7.7 Maintenance and inspection 13 7.8 Parti
15、cular requirements 13 8 Verification of the design. 13 9 Acceptance of the design 13 9.1 General. 13 9.2 The acceptance programme 14 9.2.1 Content. 14 9.2.2 Calculations. 15 9.2.3 Static tests. 15 9.2.4 Fatigue tests 15 9.2.5 On-track tests 16 10 Quality requirements 16 Annex A (informative) Load ca
16、ses. 17 Annex B (informative) Guide for the loading conditions of vehicles. 18 Annex C (informative) Loads due to bogie running. 19 C.1 General. 19 C.2 Examples of loads for bogies of passenger rolling stock - categories B-I category B-II bogies for inner and outer suburban passenger carrying vehicl
17、es, powered and un- powered; category B-III bogies for metro and rapid transit rolling stock, powered and un-powered; category B-IV bogies for light rail vehicles and trams; category B-V bogies for freight rolling stock with single-stage suspensions; category B-VI bogies for freight rolling stock wi
18、th two-stage suspensions; category B-VII bogies for locomotives. NOTE The classifications are similar to (but not wholly consistent with) those adopted for vehicle bodies in EN 12663 9. They are not exclusive and more may be added as information becomes available. 6 Responsibilities The customer sha
19、ll provide the supplier with a detailed description of the requirements of the bogie design in the form of a technical specification incorporating all appropriate mandatory regulations. The customer shall also define the parts of the acceptance procedure (clause 9) and the quality requirements (clau
20、se 10), which he specifically requires. The customer shall specify the way in which the supplier is to provide evidence to show that the requirements have been met. NOTE If the customer is unable to define the specification completely the supplier may propose a specification and submit it to the cus
21、tomer for approval. It is the suppliers responsibility to design the bogie frame in accordance with the specification. 7 Contents of technical specification 7.1 Scope The technical specification shall consist of all the information describing the functional requirements of the bogie frame and the in
22、terfaces with associated components and assemblies. It shall also comprise, as a minimum, the general requirements of use, the conditions associated with the vehicle equipped with the bogies, the operating characteristics, the conditions associated with maintenance and any other particular requireme
23、nts of the customer. 7.2 General requirements The customer shall indicate the type of bogie required in terms of its use in accordance with the categories in clause 5. The customer shall also indicate in the technical specification the intended life of the bogie, its average annual distance run and
24、its total distance run. 7.3 Vehicle conditions and interfaces The specification shall include, but not be limited to, information on: EN 13749:2005 (E) 12 vehicle masses; vehicle geometry (e.g. available space, position of the centre of gravity); bodybogie connections (e.g. mechanical, pneumatic, el
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 13749 2005
链接地址:https://www.31doc.com/p-3740085.html