《BS-EN-1398-2009.pdf》由会员分享,可在线阅读,更多相关《BS-EN-1398-2009.pdf(36页珍藏版)》请在三一文库上搜索。
1、BS EN 1398:2009 ICS 53.080 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Dock levellers Safety requirements Licensed CopyChinese University of Hong Kong, 13/06/2009 05:19, Uncontrolled Copy, (c) BSI This British Standard was published under the authority of
2、the Standards Policy and Strategy Committee on 30 April 2009 BSI 2009 ISBN 978 0 580 54576 4 Amendments/corrigenda issued since publication DateComments BS EN 1398:2009 National foreword This British Standard is the UK implementation of EN 1398:2009. It supersedes BS EN 1398:1998 which is withdrawn.
3、 The UK participation in its preparation was entrusted to Technical Committee MHE/12, Lifting platforms. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users a
4、re responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Licensed CopyChinese University of Hong Kong, 13/06/2009 05:19, Uncontrolled Copy, (c) BSI BS EN 1398:2009BS EN 1398:2009BS EN 1398:2009 EUROPEAN STANDARD NORME EUROPENNE EUR
5、OPISCHE NORM EN 1398 March 2009 ICS 53.080Supersedes EN 1398:1997 English Version Dock levellers - Safety requirements Rampes ajustables - Prescriptions de scuritLadebrcken - Sicherheitsanforderungen This European Standard was approved by CEN on 14 February 2009. CEN members are bound to comply with
6、 the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Cen
7、tre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the offici
8、al versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slov
9、enia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN na
10、tional Members. Ref. No. EN 1398:2009: E Licensed CopyChinese University of Hong Kong, 13/06/2009 05:19, Uncontrolled Copy, (c) BSI BS EN 1398:2009BS EN 1398:2009BS EN 1398:2009 EN 1398:2009 (E) 2 Contents Page Foreword 4 Introduction .5 1 Scope 6 2 Normative references 7 3 Terms and definitions .8
11、4 List of significant hazards . 10 5 Safety requirements and/or protective measures . 12 5.1 Calculations and dimensions 12 5.2 General safety requirements and protective measures 16 5.3 Additional requirements for manually operated dock levellers . 19 5.4 Additional requirements for power-operated
12、dock levellers . 20 6 Verification of the safety requirements and/or the protective measures . 24 7 Information for use . 25 7.1 General . 25 7.2 Marking 25 7.3 Instructions for use 25 7.4 Instructions for maintenance and inspection 26 Annex A (informative) Examples of suitable tests 28 A.1 General
13、. 28 A.2 Stability test . 28 A.3 Function test of the automatic safety device . 30 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC . 31 Annex ZB (informative) Relationship between this European Standard and the Essential Requ
14、irements of EU Directive 2006/42/EC . 32 Bibliography . 33 Figures Figure 1 Types of dock levellers 6 Figure 2 Main parts of a dock leveller . 9 Figure 3 Position of contact areas 14 Figure 4 Max. permanent deformation of bridge deck sheets 15 Figure 5 Safeguarding of crushing and shearing hazards .
15、 18 Figure A.1 Stability test for load case 1 29 Figure A.2 Stability test for load case 2 29 Figure A.3 Max. deformation of bridge deck sheets 29 Licensed CopyChinese University of Hong Kong, 13/06/2009 05:19, Uncontrolled Copy, (c) BSI BS EN 1398:2009BS EN 1398:2009BS EN 1398:2009 EN 1398:2009 (E)
16、 3 Tables Table 1 Significant hazards and safety requirements 11 Table 2 Applicable factors and loads at different load combinations 13 Table 3 Means of verification of the safety requirements and measures 24 Licensed CopyChinese University of Hong Kong, 13/06/2009 05:19, Uncontrolled Copy, (c) BSI
17、BS EN 1398:2009BS EN 1398:2009BS EN 1398:2009 EN 1398:2009 (E) 4 Foreword This document (EN 1398:2009) has been prepared by Technical Committee CEN/TC 98 “Lifting platforms”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by p
18、ublication of an identical text or by endorsement, at the latest by September 2009, and conflicting national standards shall be withdrawn at the latest by September 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or
19、CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1398:1997. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Direc
20、tive(s). For relationship with EC Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Bel
21、gium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed CopyChin
22、ese University of Hong Kong, 13/06/2009 05:19, Uncontrolled Copy, (c) BSI BS EN 1398:2009BS EN 1398:2009BS EN 1398:2009 EN 1398:2009 (E) 5 Introduction This European Standard is a type C-standard as defined in EN ISO 12100. The machinery concerned and the extent to which hazards, hazardous situation
23、s and hazardous events are covered are indicated in the scope of this European Standard. In addition, machinery shall comply as appropriate with EN ISO 12100 for hazards which are not covered by this European Standard. Where provisions of this type C standard are different from those which are state
24、d in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard. Licensed CopyChinese University of Hong Kong, 13/06/2009 05:19, Uncontrol
25、led Copy, (c) BSI BS EN 1398:2009BS EN 1398:2009BS EN 1398:2009 EN 1398:2009 (E) 6 1 Scope 1.1 This European Standard specifies the safety requirements for design, construction, installation, maintenance and testing of dock levellers and for safety components on dock levellers. With the exception of
26、: a) dock levellers for marine and aircraft applications; b) lifting tables; c) vehicle mounted tail lifts. NOTE 1 Requirements for lifting tables are laid down in EN 1570. NOTE 2 Requirements for vehicle mounted tail lifts are laid down in EN 1756-1. 1.2 This European Standard is applicable to dock
27、 levellers which are used by persons and/or manual or power driven transport equipment (e. g. forklift trucks) as traffic paths between goods vehicles, both road vehicles and rail wagons, and parts of buildings such as loading docks. This standard does not deal with other bridging devices not shown
28、in Figure 1. a) Bridge plate (dock plate) manually operated, mobile b)Manually or power operated dock leveller, fixed at the dock edge c) Manually operated dock leveller, installed in a pit, hinged lip d)Power operated dock leveller, installed in a pit, telescopic or hinged lip Figure 1 Types of doc
29、k levellers NOTE Only dock levellers fitted with a drive system other than directly applied human effort are machines in the sense of the Machinery Directive. 1.3 This European Standard specifies requirements in order to protect persons and objects against accidents and health problems and damage du
30、ring use and operation of dock levellers. Licensed CopyChinese University of Hong Kong, 13/06/2009 05:19, Uncontrolled Copy, (c) BSI BS EN 1398:2009BS EN 1398:2009BS EN 1398:2009 EN 1398:2009 (E) 7 Persons to protect are: a) operators and users; b) maintaining and inspecting personnel; c) persons ne
31、ar the dock leveller. Objects to be protected are: d) goods on dock levellers; e) transport equipment on dock levellers. 1.4 The significant hazards of dock levellers are listed in Clause 4. These hazards have been identified by risk assessment according to EN ISO 12100-2 and require actions to avoi
32、d the hazard, or to reduce the risk, which are covered in Clause 5. 1.5 The safety requirements are based on the assumption that the dock levellers are regularly maintained by competent persons to the instructions of the manufacturer and that the operating person has been instructed in the use of th
33、e dock leveller. 1.6 This European Standard is not applicable to dock levellers which are manufactured before the date of its publication as EN. 1.7 This European Standard deals with all significant hazards, hazardous situations and events relevant to dock Levellers, when they are used as intended a
34、nd under the conditions foreseen by the manufacturer (see Clause 4). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced do
35、cument (including any amendments) applies. EN 349, Safety of machinery Minimum gaps to avoid crushing of parts of the human body EN 982, Safety of machinery Safety requirements for fluid power systems and their components Hydraulics EN 983, Safety of machinery Safety requirements for fluid power sys
36、tems and their components Pneumatics EN 60204-1:2006, Safety of machinery Electrical equipment of machines Part 1: General requirements (IEC 60204-1:2005, modified) EN 60529:1991, Degrees of protection provided by enclosures (IP code) (IEC 60529:1989) EN 60947-4-1, Low-voltage switchgear and control
37、gear Part 4-1: Contactors and motor-starters; Electromechanical contactors and motor-starters (IEC 60947-4-1:2000) EN 60947-4-2, Low-voltage switchgear and controlgear Part 4-2: Contactors and motor-starters AC semiconductor motor controllers and starters (IEC 60947-4-2:1999) EN ISO 12100-1:2003, Sa
38、fety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003) Licensed CopyChinese University of Hong Kong, 13/06/2009 05:19, Uncontrolled Copy, (c) BSI BS EN 1398:2009BS EN 1398:2009BS EN 1398:2009 EN 1398:2009 (E) 8 EN ISO 12100-2:2003, S
39、afety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12100-2:2003) EN ISO 13849-1:2008, Safety of machinery Safety related parts of control systems Part 1: General principles for design (ISO 13849-1:2006) EN ISO 13850, Safety of machinery Emergency stop
40、Principles for design (ISO 13850:2006) ISO 11228-1, Ergonomics Manual handling Part 1: Lifting and carrying ISO 11228-2, Ergonomics Manual handling Part 2: Pushing and pulling CENELEC HD 60364-4-41, Low-voltage electrical installations Part 4-41: Protection for safety Protection against electric sho
41、ck (IEC 60364-4-41:2005, modified) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 12100-1:2003 and the following apply. 3.1 dock leveller static or mobile device to bridge the space between a loading dock or similar loading areas and the loading
42、surface of a vehicle which may be at different levels NOTE 1 Dock levellers may be built as: a) manually operated, mobile dock leveller, called bridge plate or dock board, see Figure 1a); b) power operated dock leveller built into a loading dock or fixed at the edge of a dock, see Figure 1b) and d);
43、 c) manually operated dock leveller built in to a loading dock or fixed to the edge of a dock, see Figure 1b) and c). NOTE 2 Dock levellers are provided for loading and unloading operations and are not designed to lift or lower loads. NOTE 3 The lifting or lowering mechanism is only provided to make
44、 alterations in the position of the unloaded dock leveller. 3.2 dock board/bridge plate dock leveller, consisting of a manually operated plate, suspended or loose 3.3 latched dock leveller dock leveller which is held in a certain position by a positively engaged locking device 3.4 bridge deck part o
45、f the dock leveller in the form of a plate which is used as traffic path for persons and/or transport equipment, but excluding the lip (see Figure 2) Licensed CopyChinese University of Hong Kong, 13/06/2009 05:19, Uncontrolled Copy, (c) BSI BS EN 1398:2009BS EN 1398:2009BS EN 1398:2009 EN 1398:2009
46、(E) 9 Key 1 Bridge deck 2 Bearer 3 Hinged lip Figure 2 Main parts of a dock leveller 3.5 bearer supporting part of a dock leveller in the form of a beam, fixed at the under side of the bridge deck (see Figure 2) 3.6 support device part of a dock leveller, e. g. in the form of a block, bar or bolt wh
47、ich supports the dock leveller in the horizontal stored position 3.7 hinged lip part of a dock leveller hinged to the bridge deck and resting on the vehicle in the operational position (see Figure 2) 3.8 telescopic lip part of a dock leveller which can be telescopically extended towards the vehicle
48、and which rests on the vehicle in the operational position 3.9 loading loading or unloading a vehicle using a dock leveller 3.10 free floating condition mode in which the dock leveller supported on the vehicle may follow automatically the vertical movements of the vehicle during the loading process
49、3.11 stored position position to which the dock leveller is put, or to which it returns, when loading has finished Licensed CopyChinese University of Hong Kong, 13/06/2009 05:19, Uncontrolled Copy, (c) BSI BS EN 1398:2009BS EN 1398:2009BS EN 1398:2009 EN 1398:2009 (E) 10 3.12 automatic return return cycle of the dock leveller to its stored position with or without operator initiation 3.13 installed fixed to a dock edge or built in to the loading dock or a similar area 3.14 automatic safety device devi
链接地址:https://www.31doc.com/p-3740162.html