BS-EN-15093-2008.pdf
《BS-EN-15093-2008.pdf》由会员分享,可在线阅读,更多相关《BS-EN-15093-2008.pdf(64页珍藏版)》请在三一文库上搜索。
1、BS EN 15093:2008 ICS 77.180 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Safety of Machinery Safety requirements for hot flat rolling mills Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:29, Uncontrolled Copy, (c) BSI This
2、 British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2008 BSI 2008 ISBN 978 0 580 55204 5 Amendments/corrigenda issued since publication DateComments BS EN 15093:2008 National foreword This British Standard is the UK implementation of EN 15
3、093:2008. The UK participation in its preparation was entrusted to Technical Committee MCE/23, Safety of metal producing mills. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions
4、 of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:29, Uncontrolled Copy, (c) BSI BS EN 15093:2008 EUROPEAN STANDARD NOR
5、ME EUROPENNE EUROPISCHE NORM EN 15093 October 2008 ICS 77.180 English Version Safety of Machinery - Safety requirements for hot flat rolling mills Scurit des machines - Prescriptions de scurit relatives aux laminoirs chaud pour produits plats Sicherheit von Maschinen - Sicherheitsanforderungen an Wa
6、rmflachwalzwerke This European Standard was approved by CEN on 16 August 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bib
7、liographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibilit
8、y of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, I
9、reland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stass
10、art, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15093:2008: E Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:29, Uncontrolled Copy, (c) BSI BS EN 15093:2008 EN 15093:20
11、08 (E) 2 Contents Page Foreword4 Introduction.5 1 Scope 6 2 Normative References.7 3 Terms and definitions .9 4 List of significant hazards 10 5 Safety requirements and/or measures 11 5.1 General requirements for design, planning and risk assessment .11 5.2 List of significant hazards, hazardous sit
12、uations, safety requirements and/or measures16 5.3 Additional safety requirements or measures .32 5.4 Noise reduction as a safety requirement 34 6 Verification of the safety requirements and/or measures.35 7 Information for use36 7.1 General36 7.2 Warning devices and safety signs.36 7.3 Minimum mark
13、ing36 7.4 Accompanying documents.36 7.5 Maintenance manual .39 Annex A (normative) Safety requirements and/or measures for electrical equipment and control systems at hot flat rolling mills41 Annex B (normative) Noise test code .45 Annex C (normative) Protection of persons in case of using asphyxian
14、t gases used in fire fighting systems.49 Annex D (informative) Example for manufacturers safety instructions for maintenance at hot flat rolling mills.53 Annex E (informative) Machines and/or equipment covered by this European Standard.55 Annex F (informative) Examples for the inclusion of safety me
15、asures.56 Annex G (informative) Example for the risk analysis due to interfaces 57 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC .58 Annex ZB (informative) Relationship between this European Standard and the Essential Requi
16、rements of EU Directive 2006/42/EC59 Bibliography60 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:29, Uncontrolled Copy, (c) BSI BS EN 15093:2008 EN 15093:2008 (E) 3 Figures Figure 1 Exemplary layout of a hot flat rolling mill .6 Figure F.1 Looper secured by a loc
17、king pin.56 Figure G.1 Diagram of a hypothetical plant indicating potentially hazardous interfaces.57 Tables Table 1 Significant hazards, hazardous situations, safety requirements and/or measures 18 Table 2 Main noise sources of hot flat rolling mills equipment and exemplary noise reduction measures
18、.35 Table A.1 Stop functions43 Table B.1 Example of declared dual-number noise emission values for work stations and specified measuring points.48 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:29, Uncontrolled Copy, (c) BSI BS EN 15093:2008 EN 15093:2008 (E) 4 For
19、eword This document (EN 15093:2008) has been prepared by Technical Committee CEN/TC 322 “Equipment for making and shaping of metals - Safety requirements”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an id
20、entical text or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the latest by April 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held r
21、esponsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). For relationship with EC Directive(s), see informative An
22、nex ZA and B, which is an integral part of this document. This European Standard has been elaborated by CEN/TC 322/WG 3, comprising experts from: Denmark, Germany, Italy, Sweden and the United Kingdom. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the fol
23、lowing countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Sl
24、ovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:29, Uncontrolled Copy, (c) BSI BS EN 15093:2008 EN 15093:2008 (E) 5 Introduction This European Standard is a type C standard as stated in EN ISO 12100:2003. Th
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 15093 2008
链接地址:https://www.31doc.com/p-3740210.html