BS-EN-15301-1-2007.pdf
《BS-EN-15301-1-2007.pdf》由会员分享,可在线阅读,更多相关《BS-EN-15301-1-2007.pdf(14页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 15301-1:2007 Surfaces for sports areas Part 1: Determination of rotational resistance The European Standard EN 15301-1:2007 has the status of a British Standard ICS 97.220.10 ? Licensed Copy: London South Bank University, London South Bank University, Wed May 16 04:22:19 GMT+0
2、0:00 2007, Uncontrolled Copy, (c) BSI BS EN 15301-1:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2007 BSI 2007 ISBN 978 0 580 50733 5 National foreword This British Standard was published by BSI. It is the UK implementation of
3、EN 15301-1:2007. It partially supersedes BS 7044-2.2:1990 Method 1. EN 15301-1:2007 is one of a package of standards being produced by CEN/TC 217. On publication of the entire package, BS 7044 will be withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRI/57, Sur
4、faces for sports areas. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard ca
5、nnot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments Licensed Copy: London South Bank University, London South Bank University, Wed May 16 04:22:19 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15301-
6、1 March 2007 ICS 97.220.10 English Version Surfaces for sports areas - Part 1: Determination of rotational resistance Sols sportifs - Partie 1 : Dtermination de la rsistance en rotation Sportbden - Teil 1: Bestimmung des Drehwiderstandes This European Standard was approved by CEN on 10 February 2007
7、. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on
8、 application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Ce
9、ntre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pol
10、and, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any form and by
11、 any means reserved worldwide for CEN national Members. Ref. No. EN 15301-1:2007: E Licensed Copy: London South Bank University, London South Bank University, Wed May 16 04:22:19 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 15301-1:2007 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative References
12、.4 3 Principle4 4 Apparatus .4 5 Test pieces .8 6 Conditioning.9 7 Procedure .9 8 Calculation and expression of results.9 9 Test report9 Bibliography10 Licensed Copy: London South Bank University, London South Bank University, Wed May 16 04:22:19 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 15301-1
13、:2007 (E) 3 Foreword This document (EN 15301-1:2007) has been prepared by Technical Committee CEN/TC 217 “Surfaces for sports areas”, the Secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by end
14、orsement, at the latest by September 2007, and conflicting national standards shall be withdrawn at the latest by September 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria,
15、 Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Lo
16、ndon South Bank University, London South Bank University, Wed May 16 04:22:19 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 15301-1:2007 (E) 4 1 Scope This part of EN 15301 specifies methods for determining the rotational resistance of sports surfaces. 2 Normative References The following referenced
17、 documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12229, Surfaces for sports areas - Procedure for the preparation of sy
18、nthetic turf and needle-punch test pieces 3 Principle The force required to initiate rotational movement of a test sole in contact with the sports surface being tested is measured. 4 Apparatus 4.1 The apparatus shall consist of the following components (see Figure 1). Test foot, comprised of a steel
19、 disc (150 2) mm in diameter to which the appropriate test sole is mounted. Shaft with attached lifting handles that are centrally attached to the centre of the studded disc. Two-handled mechanical torque wrench with a scale marked from 0 Nm to 80 Nm in a maximum of 2 Nm increments, that attaches to
20、 the top of the shaft. Set of annular weights that rest centrally on the upper surface of the studded disc allowing free movement of the disc beneath the weights. The total mass of the apparatus (test foot, shaft, torque wrench and weights) shall be (46 2) kg. Tripod and guide to minimize any latera
21、l movement of the test foot during testing. The tripod shall not restrict the free rotation of the shaft and the guide shall incorporate a means of holding and dropping the weighted test foot onto the test specimen from a height of (60 5) mm. 4.2 The test sole shall be as specified in the product sp
22、ecification. Standard test soles are as follows: a) Football stud test sole; Six football studs1 equally spaced on the bottom surface of the test foot (46 1) mm from the centre of the disc. The studs shall be as shown in Figure 2, be manufactured from plastic and have a Shore A hardness of (96 2). 1
23、 13 mm nylon studs supplied by Decathlon Group are an example of suitable products available commercially. This information is given for the convenience of users of this European Standard and does not constitute an endorsement by CEN of this product. Licensed Copy: London South Bank University, Lond
24、on South Bank University, Wed May 16 04:22:19 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 15301-1:2007 (E) 5 b) Smooth rubber sole; Smooth rubber disk (150 2) mm in diameter and at least 5 mm thick. The rubber shall be as given in Table 1. Licensed Copy: London South Bank University, London South
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 15301 2007
链接地址:https://www.31doc.com/p-3740263.html