《BS-EN-2155-12-1997.pdf》由会员分享,可在线阅读,更多相关《BS-EN-2155-12-1997.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2155-12:1997 Test methods for transparent materials for aircraft glazing Part 12: Determination of linear thermal expansion The European Standard EN 2155-12:1997 has the status of a British Standard ICS 49.025.99; 49.045 Licensed Copy: sheffieldun sheffieldun,
2、 na, Thu Nov 02 18:00:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2155-12:1997 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 November 1997 BSI 04-2000 ISBN
3、0 580 28134 5 National foreword This British Standard is the English language version of EN 2155-12:1997. The UK participation in its preparation was entrusted to Technical Committee ACE/62, Aerospace structural transparencies and non-reinforced plastics, which has the responsibility to: aid enquire
4、rs to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on thi
5、s committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, o
6、r by using the “Find” facility of the BSI Standards Electronic Catalogue. NOTEUnder the AECMA part numbering system, normative references to the Parts of AECMA-originated European Standards may appear in clause 2 in the form of a three-digit number e.g. -001 where the BSI and CEN systems would use t
7、he form -1. It can be assumed that, wherever referenced, the three-digit and single digit forms can be used interchangeably. For the purposes of part-marking of components produced in accordance with this standard, the three-digit form should be used. A British Standard does not purport to include a
8、ll the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i an
9、d ii, the EN title page, pages 2 to 5 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments Licensed Copy: sheff
10、ieldun sheffieldun, na, Thu Nov 02 18:00:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2155-12:1997 BSI 04-2000i Contents Page National forewordInside front cover Foreword2 Text of EN 2155-123 Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:00:38 GMT+00:00 2006, Uncontrolled Copy, (c
11、) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:00:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2155-12 July 1997 ICS 49.025.40 Descriptors: Aircraft industry, glazing, materials, transparency, plastics, tests, determinat
12、ion, thermal properties, thermal expansion English version Aerospace series Test methods for transparent materials for aircraft glazing Part 12: Determination of linear thermal expansion Srie arospatiale Mthodes dessais pour matriaux transparents pour vitrages aronautiques Partie 12: Dtermination de
13、 la dilatation thermique linaire Luft- und Raumfahrt Prfverfahren fr transparente Werkstoffe zur Verglasung von Luftfahrzeugen Teil 12: Bestimmung der linearen Wrmeausdehnung This European Standard was approved by CEN on 1997-03-27. CEN members are bound to comply with the CEN/CENELEC Internal Regul
14、ations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The Eur
15、opean Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the nat
16、ional standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisc
17、hes Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2155-12:1997 E Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:00:38 GMT+00:00 2006, Unc
18、ontrolled Copy, (c) BSI EN 2155-12:1997 BSI 04-2000 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of t
19、he National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 1998, and conflicting
20、 national standards shall be withdrawn at the latest by January 1998. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany,
21、 Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 1Scope3 2Definition3 3Apparatus3 4Specimens3 5Conditioning3 6Procedure3 7Expression of results4 8Test report4 Figure 1 Quartz-tube dilatometer5 Lice
22、nsed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:00:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2155-12:1997 BSI 04-20003 1 Scope This standard specifies the method to determine the reversible linear thermal expansion of plastics with exclusion of changes in length due to accidental factor
23、s such as changes in moisture content, degree of polymerization and stress release. Since it will not be possible to exclude all these accidental factors, the method can be expected to give only approximate values. 2 Definition For the purposes of this standard, the following definition applies: Lin
24、ear thermal expansion is defined as the change in length of a material in relation to unit length for a variation in temperature of 1 C. 3 Apparatus 3.1 Dilatometer A simple fused-quartz tube dilatometer is shown in Figure 1. Any generally accepted method of measuring thermal expansion may be used w
25、hich will be accurate to within 10 %. The accuracy of the device which measures the expansion shall be such that it measures the change in length over the temperature interval under consideration within 2 %. This device shall not exert a stress of more than 50 kPa on this specimen which shall not be
26、 distorted or indented. 3.2 Scale or caliper The scale or caliper shall be capable of measuring the test length of the specimen with an accuracy of 0,5 %. 3.3 Temperature bath The temperature of the specimen shall preferably be controlled by the use of a liquid bath. The bath shall be arranged in su
27、ch a way that uniform temperature throughout the specimen is secured. Means shall be provided for stirring the bath and for controlling its temperature within 0,2 C of the temperatures used. 4 Specimens 4.1 Preparation Specimens shall be cut or shaped, from sheet. The ends of the specimen shall be c
28、ut perpendicular to the axis of the specimen. They shall be protected by means of thin steel plates cemented to them. 4.2 Dimensions For the apparatus shown in Figure 1, specimens can be round or square and shall fit easily into the outer tube without excessive play. The length of the specimen may b
29、e 50 mm to 100 mm but its length is governed to some extent by the sensitivity of the dial gauge, the expected expansion and the desired accuracy. 5 Conditioning The specimen shall be conditioned at (23 2) C, (50 5) % relative humidity for at least 48 h prior to measurement of the test length of the
30、 specimen under these conditions. 6 Procedure The temperature range over which the coefficient of thermal expansion is to be measured shall be chosen so that no transitional regions are included. The limits of the range shall be agreed between purchaser and manufacturer. 6.1 Low temperature Mount th
31、e specimen in the apparatus and maintain the temperature of the bath at the lowest temperature at which measurements are required until the temperature of the specimen reaches the temperature of the bath. The time necessary shall be determined by preliminary measurements of temperature inside a simi
32、lar specimen. Record the reading of the dial gauge or other device indicating change in length. 6.2 High temperature Repeat the foregoing operations at the highest temperature at which measurements are required. 6.3 Check determination Repeat the operations described in 6.1 and 6.2. If the changes i
33、n length caused by heating and cooling do not agree within 10 % of their average, the cause of this discrepancy shall be investigated and if possible, eliminated (see 6.5). Otherwise the observations shall be reported, see 8.3. 6.4 Constant temperature bath Where the construction of the apparatus pe
34、rmits, it may be more convenient to alternately use two baths at the required temperatures. Care shall be taken not to disturb the apparatus during exchange. The use of two baths is preferred because it will reduce the time required to bring the specimen to the desired temperature. The test in gener
35、al shall be conducted in as short a time as possible to avoid changes in physical properties during long exposure to high and low temperatures. Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:00:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2155-12:1997 4 BSI 04-2000 6.5 Transition temp
36、erature The coefficient of thermal expansion of some materials is known to change rather abruptly at a certain temperature. To find this temperature, it is necessary to measure the coefficient of thermal expansion in narrow temperature limits, or to observe the rate of expansion during a steady rise
37、 in temperature of the specimen. Once such a transition point has been found, a separate coefficient of expansion for a temperature range below and above the transition point shall be determined. 7 Expression of results The average coefficient of thermal expansion shall be calculated from the formul
38、a: Coefficient of linear thermal expansion = where: 8 Test report It shall include: 8.1 Temperatures between which the coefficient of thermal expansion has been computed. 8.2 Average coefficient of linear thermal expansion per C 8.3 Complete description of any unusual behaviour such as, for instance
39、, a difference of more than 10 % in measured values of expansion and contraction %Lis the average of changes in length due to heating or cooling; Lis the test length of specimens immediately after the conditioning stage (%L and L being in the same units); Tis the temperature difference in C over whi
40、ch the change in length has been measured. %L L T - - Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:00:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2155-12:1997 BSI 04-20005 Figure 1 Quartz-tube dilatometer Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:00:38 GMT+00:00 200
41、6, Uncontrolled Copy, (c) BSI BS EN 2155-12:1997 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorpora
42、ted by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone f
43、inding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS w
44、hich ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standa
45、rds, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to
46、 Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive subst
47、antial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internatio
48、nal standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This doe
49、s not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 1
链接地址:https://www.31doc.com/p-3740680.html