《BS-EN-13087-6-2000.pdf》由会员分享,可在线阅读,更多相关《BS-EN-13087-6-2000.pdf(10页珍藏版)》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 13087-6:2000 Incorp
2、orating Amendment No.1 The European Standard EN 13087-6:2000, with the incorporation of amendment A1:2001, has the status of a British Standard ICS 13.340.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Protective helmets Test methods Part 6: Field of vision Licensed Copy:
3、sheffieldun sheffieldun, na, Sun Oct 29 09:23:16 GMT+00:00 2006, Uncontrolled Copy, (c) BSI This British Standard, having been prepared under the direction of the Health and Environment Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 August
4、2000 BSI 22 March 2002 ISBN 0 580 34278 6 BS EN 13087-6:2000 Amendments issued since publication Amd. No.DateComments 1360022 March 2002Addition of Annex ZA National foreword This British Standard is the official English language version of EN 13087-6:2000, including amendment A1:2001. The UK partic
5、ipation in its preparation was entrusted to Technical Committee PH/6, Head protection, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed
6、; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in thi
7、s document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of
8、 British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 7 and a back cover. The BSI cop
9、yright notice displayed in this document indicates when the document was last issued. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:23:16 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13087-6 March 2000 + A1 December 2001 ICS 13.340.20 En
10、glish version Protective helmets - Test methods - Part 6: Field of vision (includes amendment A1:2001) Casques de protection - Mthodes dessai - Partie 6: Champ visuel (inclut lamendement A1:2001) Schutzhelme - Prfverfahren - Tiel: 6 Sichtfeld (enthlt nderung A1:2001) This European Standard was appro
11、ved by CEN on 3 February 2000. Amendment A1:2001 was approved by CEN on 21 October 2001. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lis
12、ts and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the respo
13、nsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Net
14、herlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stassart, 36 B-1050 Brussels 2000 CENAll rights of exploitation in any form and by any means res
15、erved worldwide for CEN national Members. Ref. No. EN 13087-6:2000 + A1:2001 E Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:23:16 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 2 EN 13087-6:2000 BSI 22 March 2002 CONTENTS Page Foreword. 2 Introduction 4 1 Scope. 4 2 Normative reference
16、s. 4 3 Terms and definitions 4 4 Prerequisites. 4 5 Methods. 5 Annex A (normative) Test results Uncertainty of measurement 7 Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives 7 Foreword This European Standard has been prep
17、ared by Technical Committee CEN/TC 158, Head protection, the Secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2000, and conflicting national standards
18、 shall be withdrawn at the latest by September 2000. For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement
19、this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. This European Standard has been prepared under a mandate given to CEN by the Eur
20、opean Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s) It consists of ten parts as follows: Part 1: Conditions and conditioning; Part 2: Shock absorption; Part 3: Resistance to penetration; Part 4: Retention system effectiveness; Part 5: Rete
21、ntion system strength; Part 6: Field of vision; Part 7: Flame resistance; Part 8: Electrical properties; Part 9: Mechanical rigidity; Part 10: Resistance to radiant heat. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:23:16 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 3 EN 13087-6:2000
22、 BSI 22 March 2002 Foreword to amendment A1 This amendment EN 13087-6:2000/A1:2001 to EN 13087-6:2000 has been prepared by Technical Committee CEN/TC 158, Head protection, the Secretariat of which is held by BSI. This amendment to the European Standard EN 13087-6:2000 shall be given the status of a
23、national standard, either by publication of an identical text or by endorsement, at the latest by June 2002, and conflicting national standards shall be withdrawn at the latest by June 2002. This amendment to the European Standard EN 13087-6:2000 has been prepared under a mandate given to CEN by the
24、 European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this standard. According to the CEN/CENELEC Internal Regulations, the national standards
25、 organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy:
26、sheffieldun sheffieldun, na, Sun Oct 29 09:23:16 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 4 EN 13087-6:2000 BSI 22 March 2002 Introduction This standard is intended as a supplement to the specific product standards for protective helmets (helmet standards). This method or other test methods m
27、ay be applicable to complete helmets or parts thereof, and may be referenced in the other helmet standards. Performance requirements are given in the appropriate helmet standard, as are such prerequisites as the number of samples, preconditioning, preparation of samples for the tests, sequence and d
28、uration of testing and assessment of test results. If deviations from the test method given in this standard are necessary, these deviations will be specified in the appropriate helmet standard. 1 Scope This European Standard describes methods of test for protective helmets. The purpose of these tes
29、ts is to enable assessment of the performance of the helmet as specified in the appropriate helmet standard. This standard specifies the method of test for field of vision. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications.
30、These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to, or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For u
31、ndated references the latest edition of the publication referred to applies (including amendments). EN 960, Headforms for use in the testing of protective helmets EN 13087-1,Protective helmets - Test methods - Part 1: Conditions and conditioning 3 Terms and definitions For the purposes of this stand
32、ard, the terms and definitions used in this standard may be found in the appropriate helmet standard. 4 Prerequisites In order to implement this standard, at least the following parameters need to be specified in the appropriate helmet standard: a) performance requirements; b) number of samples; c)
33、preparation of samples; d) sequence of conditioning; e) sequence of tests; f) sizes of the headforms. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:23:16 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 5 EN 13087-6:2000 BSI 22 March 2002 5 Methods 5.1 General Testing shall be performed i
34、n ambient conditions specified in EN 13087-1. When the test method specifies that the helmet shall be fitted to a headform, this shall be done in accordance with the manufacturers fitting instructions, if supplied. If none are supplied, the helmet shall be fitted so as to simulate typical in use fit
35、ting. 5.2 Principle The helmet is placed on a test headform and the field of vision is measured by reference to markings on the headform. 5.3 Apparatus The apparatus shall include: a)a series of test headforms in accordance with EN 960; b)a ballast mass of (5,0 0,5) kg; c)a series of angle templates
36、 or other means of assessing angles of vision. 5.4 Procedure The size(s) of headform to be used is specified in the helmet standard. The test headform(s) to be used shall be marked with: - the following planes as defined in EN 960 and in Figure 1 of this standard respectively: - basic plane; - refer
37、ence plane; - central transverse vertical plane; - longitudinal vertical median plane; and - points K1, K2, L1, L2 as defined in Figure 1 of this standard. Place the helmet on the headform. Place the ballast mass on the crown of the helmet in order to stabilize it in position. Ensure that the longit
38、udinal vertical median plane of the helmet coincides with the longitudinal vertical median plane of the headform. Adjust the helmet on the headform in accordance with the manufacturers instructions, if supplied. If they are not supplied, adjust the helmet to simulate typical in use fitting. Once pos
39、itioned, assess, using the angle templates or other means, whether the requirements for no occultation are satisfied for the horizontal directions from points L1 and L2 and for the vertical directions, upwards from points L1 and L2, and downwards from points K1 and K2. 5.5 Report Report whether occu
40、ltation occurs in the specified field of vision. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:23:16 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 6 EN 13087-6:2000 BSI 22 March 2002 a) Section of headform at longitudinal vertical median plane Dimensions in millimetres Key 1 Reference
41、plane 2 Basic plane 3 Front 4 Back 5 Longitudinal vertical median plane 6 Central transverse vertical plane b) Section of headform at the reference plane Figure 1 - Field of vision Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:23:16 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 7 EN 13
42、087-6:2000 BSI 22 March 2002 Annex A (normative) Test results Uncertainty of measurement For each of the required measurements performed in accordance with this standard, a corresponding estimate of the uncertainty of measurement shall be evaluated. This estimate of uncertainty shall be applied and
43、stated when reporting test results, in order to enable the user of the test report to assess the reliability of the data. Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives This European Standard has been prepared under a m
44、andate given to CEN by the European Commission and the European Free Trade Association and supports essential requirements of EU Directive on personal protective equipment (PPE) 89/686/EEC. WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling within the sco
45、pe of this standard. The following clauses of this standard are likely to support requirements of Directive 89/686/EEC: EU Directive 89/686/EEC, Annex IIClause of this standard 1.1 Design principles5 1.3 Comfort and efficiency5 Compliance with the clauses of this standard provides one means of confo
46、rming with the specific essential requirements of the Directive concerned and associated EFTA regulations. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:23:16 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 13087-6:2000 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Inst
47、itution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards s
48、hould make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical comm
49、ittee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at htt
链接地址:https://www.31doc.com/p-3740903.html