《BS-EN-1392-1998.pdf》由会员分享,可在线阅读,更多相关《BS-EN-1392-1998.pdf(14页珍藏版)》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1392:1998 The Europ
2、ean Standard EN 1392:1998 has the status of a British Standard ICS 61.060; 83.180 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Adhesives for leather and footwear materials Solvent-based and dispersion adhesives Test methods for measuring the bond strength under specified co
3、nditions Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 12:31:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI This British Standard, having been prepared under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into
4、 effect on 15 July 1998 BSI 1998 ISBN 0 580 29647 4 BS EN 1392:1998 Amendments issued since publication Amd. No.DateText affected National foreword This British Standard is the English language version of EN 1392:1998 published by the European Committee for Standardization (CEN). The UK participatio
5、n in its preparation was entrusted to Technical Committee STI/52, Adhesives, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor
6、related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document
7、 may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British S
8、tandards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 11 and a back cover. Licensed Copy: sheff
9、ieldun sheffieldun, na, Sun Oct 29 12:31:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any f
10、orm and by any means reserved worldwide for CEN national Members. Ref. No. EN 1392:1998 E EUROPEAN STANDARDEN 1392 NORME EUROPE ENNE EUROPA ISCHE NORM February 1998 ICS 61.060; 83.180 Descriptors: Adhesives, footwear, materials, leather, rubber, polyvinyl chloride, bonding, destructive test, bond st
11、rength, peel test, shear test, creep test at elevated temperature, test method, testing conditions, classification English version Adhesives for leather and footwear materials Solvent-based and dispersion adhesives Test methods for measuring the bond strength under specified conditions Adhe sifs pou
12、r cuir et mate riaux de la chaussure Adhe sifs a base de solvants ou a dispersion Me thodes dessai de la re sistance pour mesurer la re sistance de collage dans certaines conditions spe cifie es Klebstoffe fu r Leder und Schuhwerkstoffe Lo semittel- und Dispersionsklebstoffe Pru fverfahren zur Messu
13、ng der Festigkeit von Klebungen unter festgelegten Bedingungen This European Standard was approved by CEN on 24 January 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard w
14、ithout any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other languag
15、e made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Ice
16、land, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 12:31:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 2 EN 1392:1998 BSI 1998 Foreword This European Standard has been prepared by
17、 Technical Committee CEN/TC 193, Adhesives, the Secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 1998, and conflicting national standards shall be with
18、drawn at the latest by August 1998. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
19、Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 1Scope3 2Normative references3 3Definitions3 4Principle3 5Safety3 6Test methods3 6.1Types of tests3 6.2Adhesives and materials3 6.3Apparatus4 6.4Form of test pieces4 6.5Number of tes
20、t pieces5 6.6Preparation of test pieces5 6.7Storage and ageing of test pieces8 6.8Procedures and evaluation8 6.9Test report11 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 12:31:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 3 EN 1392:1998 BSI 1998 1 Scope This standard specifies test m
21、ethods to measure some strength properties of bonds of leather and footwear materials, in stuck-on assemblies using solvent-based and dispersion adhesives, under different conditions. These can be chosen taking into account the different stresses that such bonds are subjected to, depending on the ty
22、pe of footwear, under different external conditions in service. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed he
23、reafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 923, Adhesives Terms and defin
24、itions. EN 1066, Adhesives Sampling. EN 1067, Adhesives Examination and preparation of samples for testing. EN 10002-2, Metallic materials Tensile testing Part 2: Verification of the force measuring system of the tensile testing machine. EN 29142, Adhesives Guide to the selection of standard laborat
25、ory ageing conditions for testing bonded joints (ISO 9142:1990). EN ISO 10365, Adhesives Designation of main failure patterns (ISO 10365:1992). ISO 554, Standard atmospheres for conditioning and/or testing Specifications. ISO 868, Plastic and ebonite Determination of indentation hardness by means of
26、 a durometer (Shore hardness). ISO 2602, Statistical interpretation of test results Estimation of the mean Confidence interval. 3 Definitions For the purposes of this standard, the definitions in accordance with EN 923 and the following definitions apply: 3.1 leather tanned animal skin, usually free
27、 of hair EN 1391 3.2 footwear materials natural and synthetic materials which are suitable for footwear manufacture or repair and have adequate wear properties as upper or sole material EN 1391 3.3 adhesives for leather and footwear materials adhesives which are intended to produce firm and durable
28、bonds with leather and footwear materials 4 Principle The surface of the leather or the footwear material used shall be treated specifically to the nature of the material. Strips of specified length and width shall be cut from the treated material. Two of these strips or one strip of the above menti
29、oned material together with one strip of a suitable different material shall be bonded by an adhesive to test pieces of specified form. The test pieces shall be stored under specified conditions and their bond strength determined under specified conditions. 5 Safety Persons using this standard shall
30、 be familiar with normal laboratory practice. This standard does not purport to address all the safety problems, if any, associated with its use. It is the responsibility of the user to establish safety and health practices and to ensure compliance with any European or national regulatory conditions
31、. 6 Test methods 6.1 Types of tests 6.1.1 Peel test at (232) 8C See 6.4.2. 6.1.2 Shear test at (232) 8C See 6.4.3. 6.1.3 Peel test under constant load and at a constant elevated temperature (creep test) See 6.4.4. 6.2 Adhesives and materials 6.2.1 Footwear adhesive The adhesive used shall be identif
32、ied in the test report, in particular note name and/or designation, manufacturer, date of manufacture/supply and/or lot number, main polymer and colour. For two-part adhesives the nature of the crosslinking agent and the mixing ratio of the components shall be identified. Reference footwear test adh
33、esives are one- or two-part adhesives with specified properties (e.g. test adhesive CR 1, test adhesive CR 2, test adhesive PU 1, test adhesive PU 2). The designation of the reference test adhesive, if used, shall be recorded in the test report. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29
34、 12:31:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 4 EN 1392:1998 BSI 1998 6.2.2 Footwear materials The footwear material(s) used in the test report shall be identified. The name and/or designation, manufacturer, date of manufacture/supply, type of leather or of footwear material, e.g. soling
35、 or upper material shall be recorded. For leathers list colour, thickness and type of tannage (if known), for rubber and plastic materials colour, polymer base and Shore-hardness in accordance with ISO 868. The identification of this material shall be included in the test report. Reference footwear
36、test materials are footwear materials with specified properties (e.g. test leather 1, test leather 2, test material SBR 1, test material SBR 2, test material NBR, test material SBSR or test material PVC). The designation of the reference footwear test materials, if used, shall be included in the tes
37、t report. 6.3 Apparatus The items required shall depend on the types of materials used: 6.3.1 Cutting knife, sharp, for cutting test pieces in accordance with 6.6.2. The angle between the inner and outer cutting surface shall be approximately 208. 6.3.2 Splitting machine, for splitting bottom leathe
38、r. 6.3.3 Roughing machine, a rotary wire brush with a wire diameter between 0,1 mm and 0,4 mm. The linear speed of revolution shall be between 10 m/s and 25 m/s. 6.3.4 Scouring machine, A drum covered with emery paper or emery cloth of 40 grit size and a linear speed of revolution of between 10 m/s
39、and 20 m/s. 6.3.5 Hard felt disc, made from wool for removing thin polyvinyl chloride (PVC), coats from PVC upper materials. 6.3.6 Hand brush, mechanical device for removing the dust from strips of material, after roughing. 6.3.7 Material for solvent wiping, a lint-free fabric or cotton wool unaffec
40、ted by the solvent used, of about 150 mm 3 150 mm in size. 6.3.8 Solvents, ethyl acetate or acetone and light petroleum, boiling range 80 8C to 110 8C. 6.3.9 Halogenation agent, solvent borne, 1- or 2-part, for treating rubber surfaces. 6.3.10 Brushes, brush with a non-metallic bristle holder for ha
41、logenation and the bristles shall be (205) mm long. 6.3.11 Adhesive applicator, brush, roller, coating machine, etc. to apply a uniform coating of the adhesive under test. 6.3.12 Heat activator, for heating adhesive coats to the required temperature. 6.3.13 Equipment for measurement of temperature,
42、thermocouple, thermo-indicator papers or melting powders for measuring the temperature of activated adhesive coats. 6.3.14 Pressing device, providing an even pressure of up to 0,6 MPa over the whole of the surface to be bonded. 6.3.15 Tensile testing machine, for measuring maximum separation forces
43、up to 10 kN and suitable force measurement ranges in accordance with class 2 of EN 10002-2. To record automatically, the separation forces determined, and adjustable to a constant rate of traverse of (10010) mm/min during the test. 6.3.16 Oven, with forced ventilation capable of storing test pieces
44、at (502) 8C. 6.3.17 Warm air cabinet, with forced ventilation capable of maintaining the contents at temperatures between (402) 8C and (1002) 8C and suitable for testing test pieces. The test cabinet shall be fitted with a window and devices for clamping five test pieces. These devices shall consist
45、 of upper clamps fixed on a metal bar in the cabinet and lower clamps which shall have means for attaching weights which pass through cylindrical holes in the base of the cabinet. All lower clamps shall be of the same mass and capable of being loaded with weights so that total loads applied by the i
46、ndividual clamps are 0,5 kg, 1,0 kg, 1,5 kg, 2,0 kg and 2,5 kg. 6.3.18 Weights, for applying loads of 0,5 kg, 1,0 kg, 1,5 kg, 2,0 kg and 2,5 kg, (with a tolerance of1 %) including the weight of a clamp to the test pieces. 6.4 Form of test pieces 6.4.1 General Prepare from the footwear materials, str
47、ips as specified in 6.6.1 to 6.6.3. Alternatively, if a material does not allow the cutting of strips of the required dimensions, smaller and/or shorter strips can be used for preparing test pieces of the specified form, subject to the recording of their dimensions and overlap in the test report. 6.
48、4.2 Peel test at (232) C Bond two strips of material not greater than (1002) mm long and (300,5) mm wide to cover each other over a length of at least (602) mm (see Figure 1). 6.4.3 Shear test at (232) C Bond two strips of material, (802) mm long and (200,2) mm wide with an overlap of (100,2) mm (se
49、e Figure 2). Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 12:31:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 5 EN 1392:1998 BSI 1998 Dimensions in millimetres 1 Length of the bond Figure 1 Form and dimensions of test pieces for the peel tests Dimensions in millimetres 1 Test length 2 Shear section 200 mm2 Figure 2 Form and dimensions of test pieces for shear tests 6.4.4 Peel test under constant load and at a constant elevated temperature (creep test) Use the test
链接地址:https://www.31doc.com/p-3740959.html