BS-EN-1338-2003.pdf
《BS-EN-1338-2003.pdf》由会员分享,可在线阅读,更多相关《BS-EN-1338-2003.pdf(76页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1338:2003 Incorporating Corrigendum No. 1 Concrete paving blocks Requirements and test methods The European Standard EN 1338:2003 has the status of a British Standard ICS 93.080.20 ? BS EN 1338:2003 This British Standard was published under the authority of the Standards Polic
2、y and Strategy Committee on 29 May 2003 BSI July 2006 ISBN 0 580 41965 7 National foreword This British Standard is the official English language version of EN 1338:2003, including Corrigendum May 2006. EN 1338 is a candidate “harmonized” European Standard and fully takes into account the requiremen
3、ts of the European Commission mandates M/119, Floorings, and M/122, Roof Coverings, given under the EU Construction Products Directive (89/106/EEC), and intended to lead to CE marking. The date of applicability of EN 1338 as a harmonized European Standard, i.e. the date after which this standard may
4、 be used for CE marking purposes, is subject to an announcement in the Official Journal of the European Communities. The Commission in consultation with the Member States have agreed a transition period for the co-existence of harmonized European Standards and their corresponding national standard(s
5、). It is intended that this period will comprise a period, usually nine months, after the date of availability of the European Standard, during which any required changes to national regulations are to be made, followed by a further period, usually of 12 months, for the implementation of CE marking.
6、 At the end of this co-existence period, the national standard(s) will be withdrawn. EN 1338 is the subject of transitional arrangements agreed under the Commission mandate. In the UK, the corresponding national standard is: BS 6717:2001, Precast, unreinforced concrete paving blocks Requirements and
7、 test methods; and based on this transition period of twenty-one months, BS 6717:2001 would be withdrawn in February 2005. NOTE This date is approximate. Users of this standard should contact BSI Customer Services for confirmation of withdrawal. The UK participation in the preparation of EN 1338:200
8、3 was entrusted by Technical Committee B/507, Paving units, kerbs, screeds and in-situ floorings, to its Subcommittee, B/507/1, Paving units and kerbs (precast concrete), which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secre
9、tary. Attention is drawn to National Annex NA (informative), which contains additional information and advice on the use of different performance classes for users in the UK. Cross-references The British Standards which implement international or European publications referred to in this document ma
10、y be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users
11、are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, a
12、nd keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 72, an inside back cover and a back cover. The BSI copyright date dis
13、played in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments 1647031 July 2006Corrections indicated using tags. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1338 May 2003 ICS 93.080.20 Incorporating Corrigendum May 2006 Englis
14、h version Concrete paving blocks - Requirements and test methods Pavs en bton - Prescriptions et mthodes dessaiPflastersteine aus Beton - Anforderungen und Prfverfahren This European Standard was approved by CEN on 16 October 2002. CEN members are bound to comply with the CEN/CENELEC Internal Regula
15、tions which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This Europ
16、ean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the nationa
17、l standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORM
18、ALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2003 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1338:2003 E EN 1338:2003 (E) 2 Contents page Foreword5 1Scope 6 2Normative referenc
19、es6 3Terms and definitions7 4Requirements for materials 9 4.1General9 4.2Asbestos.9 5Requirements for products.9 5.1General9 5.2Shape and dimensions10 5.2.1General10 5.2.2Work dimensions.10 5.2.3Spacer nibs, draw or chased and profiled side faces 10 5.2.4Permissible deviations10 5.3Physical and mech
20、anical properties11 5.3.1General11 5.3.2Weathering resistance.11 5.3.3Tensile splitting strength12 5.3.4Abrasion resistance.12 5.3.5Slip/skid resistance .13 5.3.6Fire performance13 5.3.7Thermal conductivity.14 5.4Visual aspects14 5.4.1Appearance 14 5.4.2Texture14 5.4.3Colour .14 6Evaluation of confo
21、rmity criteria14 6.1General14 6.1.1Demonstration of conformity .15 6.1.2Assessment of conformity15 6.2Type testing of the product 15 6.2.1Initial type testing 15 6.2.2Further type testing.15 6.2.3Sampling, testing and conformity criteria.16 6.3Factory production control.17 6.3.1General17 6.3.2Equipm
22、ent 17 6.3.3Raw and other incoming materials17 6.3.4Production process.17 6.3.5Product testing.17 6.3.6Marking, storage and delivery of products.17 6.3.7Non-conforming products 18 6.3.8Product conformity criteria.18 7Marking.19 8Test report20 Annex A (informative) Inspection schemes.21 EN 1338:2003
23、(E) 3 A.1Equipment inspection .21 A.2Materials inspection 22 A.3Production process inspection23 A.4Product inspection 23 A.5Switching rules 24 Annex B (normative) Procedure for acceptance testing of a consignment at delivery25 B.1General25 B.2Sampling procedure25 B.3Conformity criteria.26 Annex C (n
24、ormative) Measurement of the dimensions of a single block 27 C.1Preparation.27 C.2Plan dimensions 27 C.3Thickness .27 C.4Flatness and bow.27 C.5Chamfer 28 C.6Thickness of facing layer28 C.7Examples of measuring equipment.28 C.8Test report30 Annex D (normative) Determination of freeze/thaw resistance
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 1338 2003
链接地址:https://www.31doc.com/p-3740963.html