《BS-EN-13640-2002.pdf》由会员分享,可在线阅读,更多相关《BS-EN-13640-2002.pdf(14页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13640:2002 Stability testing of in vitro diagnostic reagents The European Standard EN 13640:2002 has the status of a British Standard ICS 11.100 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 13640:2002 This British Standard, having been prepared
2、under the direction of the Health and Environment Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 3 May 2002 BSI 3 May 2002 ISBN 0 580 39653 3 National foreword This British Standard is the official English language version of
3、 EN 13640:2002. The UK participation in its preparation was entrusted to Technical Committee CH/69, In vitro diagnostic systems, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards
4、which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard doe
5、s not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsibl
6、e European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title pa
7、ge, pages 2 to 10, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13640 March 2002 ICS 11.100 English
8、version Stability testing of in vitro diagnostic reagents Essais de stabilit des ractifs de diagnostic in vitroHaltbarkeitsprfung von Reagenzien fr in-vitro- diagnostische Untersuchungen This European Standard was approved by CEN on 27 December 2001. CEN members are bound to comply with the CEN/CENE
9、LEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN
10、 member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN memb
11、ers are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORM
12、ALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2002 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13640:2002 E EN 13640:2002 (E) 2 Foreword This document EN 13640:2002 has been prep
13、ared by Technical Committee CEN/TC 140 “In vitro diagnostic medical devices“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2002, and conflicti
14、ng national standards shall be withdrawn at the latest by September 2002. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), se
15、e informative annex ZA, which is an integral part of this document. Annexes A and ZA are for information only. This standard includes a Bibliography. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europea
16、n Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. EN 13640:2002 (E) 3 1 Scope This European Standard is applicable to the stability tes
17、ting of in vitro diagnostic reagents including reagent products, calibrators, control materials and kits, hereinafter called IVD reagents. It specifies general requirements for stability testing and gives specific requirements for real-time testing and accelerated testing when generating stability d
18、ata in the determination of IVD reagent shelf-life including transport stability; determination of stability of the IVD reagent in use after the first opening of the primary container (e. g. on-board stability); monitoring of stability of IVD reagents already placed on the market; verification of st
19、ability after IVD reagent modifications that may affect stability. This standard does not apply to instruments, apparatus, equipment, systems, or specimen receptacles. 2 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 2.1 accelerated stabi
20、lity study stability study designed to increase the rate of chemical or physical degradation of an in vitro diagnostic reagent by using exaggerated conditions with the purpose of predicting the shelf-life NOTE The design of an accelerated study may include elevated temperature, high humidity, light
21、and vibration. 2.2 batch lot defined amount of material, either starting material, intermediate or finished product, which is uniform in its properties and has been produced in one process or series of processes EN 375:2001 2.3 expiry date date up to which product performance is assured by the manuf
22、acturer based on the stability of the IVD reagent EN 375:2001 2.4 in vitro diagnostic reagent IVD reagent in vitro diagnostic medical device which is a reagent, reagent product, calibrator, control material or kit NOTE 1 For the definition of an in vitro diagnostic medical device see Bibliography. N
23、OTE 2 In some cases a particular IVD reagent, as defined for use in human medicine, may serve also in veterinary medicine. EN 375:2001 EN 13640:2002 (E) 4 2.5 real-time stability testing exposing the IVD reagent to the conditions anticipated by the manufacturer to which an IVD reagent is exposed dur
24、ing transportation, storage and use, and investigating robustness and stability under these conditions 2.6 shelf life period until expiry date EN 375 : 2001 2.7 stability ability of an IVD reagent, when kept under specified conditions, to retain throughout the shelf life its properties and/or perfor
25、mance within limits specified by the manufacturer EN 375 : 2001 3 General requirements 3.1 Protocol Conclusions on IVD reagent stability shall be based on data that are generated in accordance with a pre-established protocol including details at least on: responsibilities; clear IVD reagent identifi
26、cation; presumed storage conditions; objective and purpose of testing; information about the samples (e.g. number of batches, amount , container, identification); storage conditions recommended for the samples (e.g. frozen, refrigerated, room temperature); simulation of transport as appropriate; int
27、ervals between examinations; examinations to be performed at the end of each interval (e. g. procedure and extent of testing); stability criteria to be met; interpretation of data. 3.2 Final report A final report shall be prepared to complete each study. This report shall at least include or refer t
28、o the protocol which was followed; the batch(es) involved; all testing results obtained; EN 13640:2002 (E) 5 summary and conclusions regarding stability. The final report shall be part of the technical documentation related to the IVD reagent. 4 Procedures 4.1 General Stability assessment shall in p
29、rinciple be based on data derived from real-time testing. Depending on the risk associated with the IVD reagent, data derived from accelerated testing as well as experience gained with similar IVD reagents that can reasonably be expected to be comparable as regards their stability profile may also b
30、e taken into account. If at the time of placing an IVD reagent onto the market, stability claims are based on such previous data, these data shall be subsequently verified by real-time testing. Testing may be performed on any IVD reagent batch provided that the manufacturing conditions do not essent
31、ially differ from the routine production conditions. To cover remaining uncertainties, the stability claims shall include an adequate safety margin. The manufacturer shall consider the need for regular monitoring of the stability of an IVD reagent already placed on the market and, where necessary, e
32、stablish an appropriate monitoring programme. Examinations at the end of shelf-life can be sufficient for this purpose. The minimum number of batches to be investigated depending on the objective of testing shall be 3 batches for the verification of a new IVD reagent shelf-life (long-term stability)
33、; 1 batch for transport simulation; 1 batch for in-use stability of IVD reagents, for example those which are to be reconstituted or were initially packed under vacuum. In other cases at least the following number of batches shall be investigated: 3 batches for extension of an IVD reagent shelf-life
34、; 1 batch for IVD reagent modification. In any case, at the time of placing the IVD reagent onto the market, all stability claims shall be justified by adequate data, considering the risks associated with the IVD reagent and the potential influence of critical raw materials, where appropriate. NOTE
35、“Critical“ is meant with respect to stability. 4.2 Real-time stability testing 4.2.1 Objectives of real-time stability testing 4.2.1.1 General Real-time stability testing shall include long-term stability covering the shelf-life, transport simulation and in-use stability. 4.2.1.2 Long-term stability
36、 During long-term stability testing the IVD reagent shall be stored under the conditions recommended by the manufacturer (e. g. temperature, humidity). EN 13640:2002 (E) 6 Examinations shall be undertaken at specified time intervals as indicated in the protocol. The time intervals shall be chosen to
37、 encompass at least the whole of the target shelf life and, if appropriate, continue until significant degradation in the performance of the IVD reagent can be determined. The number of time intervals shall be appropriately chosen so that trends may be discerned from variability of the data. 4.2.1.3
38、 Transport simulation The simulation of the transport stress shall be based on the knowledge of the transport conditions (e. g. duration of transport, expected temperatures and humidity). Where appropriate, an investigation shall be performed to determine the real transport conditions as a basis for
39、 this simulation. 4.2.1.4 In-use stability The real-time stability testing for the purpose of determining the in-use stability shall reflect the routine conditions of use as specified by the manufacturer. 4.2.2 Procedure 4.2.2.1 Material There shall be a sufficient amount of the IVD reagent batch to
40、 be tested to last for the whole test period. If the IVD reagent is not stored or exposed in the final configuration, in particular in terms of volume and material of the primary container, the manufacturer shall base this decision on an adequate justification. 4.2.2.2 Examinations and assessment In
41、 designing analytical procedures the manufacturer shall consider the variability which may be encountered due to equipment and IVD reagents. The number of examinations to be performed with an IVD reagent depends on the precision of the test methods used. Assessment of the individual test results sha
42、ll be based on pre-established stability criteria. 4.3 Accelerated stability testing 4.3.1 Storage conditions and testing intervals Although other factors may also be of interest (e. g. sensitivity to light, humidity, low temperature), typically IVD reagents are exposed to different elevated tempera
43、tures. The manufacturer shall specify these stress conditions and the testing intervals. The test conditions chosen should, where appropriate, demonstrate significant deterioration of the IVD reagent over the testing period in order to allow for a mathematical extrapolation. 4.3.2 Procedure 4.3.2.1
44、Material The material under investigation shall be stored under the conditions defined until the accelerated testing programme starts. Sufficient amounts of the material shall then be exposed to the defined stress conditions. Samples shall be removed at the specified times and stored under the defin
45、ed conditions until analysis. If the IVD reagent is not exposed in the final configuration, in particular in terms of volume and material of the primary container, the manufacturer shall base this decision on an adequate justification. EN 13640:2002 (E) 7 4.3.2.2 Examinations and assessment Examinat
46、ions shall be performed according to the procedures described in the protocol. The number of examinations to be performed with an IVD reagent representing a specific storage condition and time depends on the precision of the test methods used. 4.3.3 Interpretation of results If the results of accele
47、rated testing are to be used to predict the shelf-life under the recommended storage conditions in the absence of sufficient real-time data, this shall be done on the basis of experience with similar IVD reagents and/or by using the Arrhenius equation or other stated models. EN 13640:2002 (E) 8 Anne
48、x A (informative) Procedure for predicting the shelf-life from accelerated stability testing based on the Arrhenius equation If a prediction of stability for a given storage temperature is intended to be based on the Arrhenius equation, the calculation can be done as follows: a) For each temperature
49、 the decimal log of concentration (y axis) is plotted versus time (x axis) and the regression equation y = ax + b is calculated. b) The percentage of the time “zero“ value, at which the IVD reagent is no longer acceptable, is calculated on the basis of the defined stability criteria. The result is converted to decimal log concentration. c) For each temperature in the equation according to a) “y“ is substituted by decimal log concentration according to b) and the stability time (x) is calculated. d) The
链接地址:https://www.31doc.com/p-3741037.html