BS-EN-15027-2007.pdf
《BS-EN-15027-2007.pdf》由会员分享,可在线阅读,更多相关《BS-EN-15027-2007.pdf(38页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 15027:2007 Transportable wall saw and wire saw equipment for job site Safety The European Standard EN 15027:2007 has the status of a British Standard ICS 25.080.60; 91.220 ? Licensed Copy: London South Bank University, London South Bank University, Wed Jan 02 02:00:44 GMT+00:0
2、0 2008, Uncontrolled Copy, (c) BSI BS EN 15027:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2007 BSI 2007 ISBN 978 0 580 57947 9 National foreword This British Standard is the UK implementation of EN 15027:2007. The UK par
3、ticipation in its preparation was entrusted by Technical Committee B/513, Construction equipment and plant and site safety, to Panel B/513/-/6, Demolition, cutting, roughening, smoothing and splitting machines Safety. A list of organizations represented on this committee can be obtained on request t
4、o its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments Lic
5、ensed Copy: London South Bank University, London South Bank University, Wed Jan 02 02:00:44 GMT+00:00 2008, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15027 November 2007 ICS 91.220; 25.080.60 English Version Transportable wall saw and wire saw equipment for job
6、site - Safety Scies murales et scies fil transportables de chantier - Scurit Transportable Wand- und Seilsgen fr den Baustelleneinsatz - Sicherheit This European Standard was approved by CEN on 7 October 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate
7、the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exist
8、s in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bo
9、dies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. E
10、UROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15027:2007: E Licensed C
11、opy: London South Bank University, London South Bank University, Wed Jan 02 02:00:44 GMT+00:00 2008, Uncontrolled Copy, (c) BSI EN 15027:2007 (E) 2 Contents Page Foreword4 Introduction.5 1 Scope 6 2 Normative references6 3 Terms and definitions .7 4 List of significant hazards 11 5 Safety requiremen
12、ts and/or measures 12 6 Verification of safety requirements and/or measures17 7 Information for use17 Annex A (normative) Noise test code Grade 2 of accuracy .22 A.1 General22 A.2 Measurement of the A-weighted emission sound pressure level at the work station .22 A.3 Determination of the A-weighted
13、sound power level emitted by the machine .22 A.4 Operating conditions.22 A.5 Information to be recorded.23 A.6 Information to be reported23 A.7 Noise declaration by the manufacturer.23 Annex B (normative) Requirements for cutting-off wheel and wire guards25 B.1 General25 B.2 Tool guards for wall saw
14、s.25 B.3 Tool guard for wire saws 26 Annex C (normative) Pictograms.28 Annex D (normative) Verification of surface temperature.29 D.1 Test equipment 29 D.2 Test method29 D.3 Test acceptance.29 Annex E (informative) Examples for working areas and dangerous areas for wire saws.30 Annex ZA (informative
15、) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC33 Bibliography34 Figures Figure 1 Components of a wall saw 8 Figure 2 Components of a wire saw 10 Figure B.1 Wall saw Tool guard. 25 Figure B.2 Wire saw Tool guard. 26 Figure C.1 “Caution, risk of c
16、utting” 28 Licensed Copy: London South Bank University, London South Bank University, Wed Jan 02 02:00:44 GMT+00:00 2008, Uncontrolled Copy, (c) BSI EN 15027:2007 (E) 3 Figure C.2 “Read operators instructions“ (see ISO 7000:2004)28 Figure C.3 “Ear Hearing protection shall be worn” 28 Figure C.4 “Eye
17、 protection shall be worn” .28 Figure C.5 “Hand protection shall be worn“.28 Figure D.1 Test cone to detect hot surface29 Figure E.1 Danger zones for wall cutting with additional wire guiding devices .30 Figure E.2 Danger zones for wall cutting without additional wire guiding devices31 Figure E.3 Da
18、nger zones for floor cutting32 Tables Table 1 List of significant hazards .11 Table B.1 Minimum thickness of tool guard parts for wall saws26 Table B.2 Minimum thickness of tool guard parts for wire saws27 Licensed Copy: London South Bank University, London South Bank University, Wed Jan 02 02:00:44
19、 GMT+00:00 2008, Uncontrolled Copy, (c) BSI EN 15027:2007 (E) 4 Foreword This document (EN 15027:2007) has been prepared by Technical Committee CEN/TC 151 “Construction equipment and building material machines Safety”, the secretariat of which is held by DIN. This European Standard shall be given th
20、e status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2008, and conflicting national standards shall be withdrawn at the latest by May 2008. Attention is drawn to the possibility that some of the elements of this document may be the subje
21、ct of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s)
22、. For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
23、 Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: London South Bank
24、 University, London South Bank University, Wed Jan 02 02:00:44 GMT+00:00 2008, Uncontrolled Copy, (c) BSI EN 15027:2007 (E) 5 Introduction This document is a type C standard as stated in EN ISO 12100-1:2003. The machinery concerned and the extent to which hazards, hazardous situations and events are
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 15027 2007
链接地址:https://www.31doc.com/p-3741123.html