BS-EN-13229-2001-A2-2004.pdf
《BS-EN-13229-2001-A2-2004.pdf》由会员分享,可在线阅读,更多相关《BS-EN-13229-2001-A2-2004.pdf(102页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13229:2001 A2:2004 Incorporating corrigenda September 2003, June 2006 and August 2007 Inset appliances including open fires fired by solid fuels Requirements and test methods ICS 97.100.30 ? BS EN 13229:2001+A2:2004 This British Standard was published under the authority of th
2、e Standards Policy and Strategy Committee and comes into effect on 5 September 2001 BSI 2008 ISBN 978 0 580 60011 1 National foreword This British Standard is the UK implementation of EN 13229:2001+A2:2004, incorporating corrigenda September 2003, June 2006 and August 2007. It supersedes BS EN 13229
3、:2001+A1:2003 which is withdrawn. The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !“. The start and finish of tex
4、t introduced or altered by corrigendum is indicated in the text by tags. Text altered by CEN corrigendum August 2007 is indicated in the text by . Conflicting national standards will need either to be withdrawn or amended and these are under consideration in Technical Committee RHE/28. It is the int
5、ention of the committee to reach a decision by April 2008 on which course of action will be taken. The UK participation in its preparation was entrusted to Technical Committee RHE/28, Domestic solid mineral fuel appliances. A list of organizations represented on this committee can be obtained on req
6、uest to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication Amd. No.
7、 DateComments 1475017 November 2003See national foreword 1549319 January 2005See national foreword 16546 Corrigendum No. 1 31 October 2006Replacement of formula (18) in A.6.2.7.1, Correction to A.6.2.1.1, A.6.2.9 and EN foreword, amendment A2 30 April 2008Implementation of CEN corrigendum August 200
8、7 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13229:2001+A2 September 2004 English version Inset appliances including open fires fired by solid fuels Requirements and test methods Foyers ouverts et inserts combustibles solides Exigences et mthodes dessai Kamineinstze einschlielich offene Ka
9、mine fr feste Brennstoffe Anforderungen und Prfung This European Standard was approved by CEN on 7 April 2001. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alte
10、ration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by transla
11、tion under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hunga
12、ry, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de
13、Stassart, 36 B-1050 Brussels 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. ICS 97.100.30 Incorporating corrigenda September 2003, June 2006 and August 2007 Ref. No. EN 13229:2001 E Page 2 BS EN 13229:2001+A2:2004 CONTENTS page Foreword.
14、3 1 Scope4 2 Normative references5 3 Terms and definitions.6 4 Materials, design and construction .15 5 Safety24 6 Performance26 7 Appliance instructions31 8 Marking34 9 Evaluation of conformity35 Annex A (normative) Test methods43 Annex B (normative) Test fuels and recommended fuels.86 Annex C (inf
15、ormative) Deleted Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive.92 Bibliography.98 Tables Table 1 - Categorisation of appliances4 Table 2 - Steel material types .20 Table 3 - Steel Nominal minimum wall thicknesses21 Table
16、 4 - Cast Iron - Minimum wall thicknesses22 Table 5 - Minimum mechanical requirements for cast iron22 Table 6 - Minimum thread size designation of flow and return tappings .23 Table 7 - Minimum depth of tapping or length of thread23 Table 8 - Deleted Table 9 - Deleted Table 10 - Minimum refuelling i
17、ntervals at nominal heat output.29 Table 11 - Minimum refuelling intervals or burning rate at slow or reduced combustion30 Table 12 - Characteristics to take account of in deciding family of appliances38 Table 13 - Performance characteristics to take account of in deciding family of appliances39 Tab
18、le A.1 - Uncertainty of measurement47 Table A.2 - Notations and units used in calculations66 Table B.1 - Test fuel specifications89 Table B.2 - Typical commercial fuel specifications .90 Table ZA.1 - Relevant clauses for Inset appliances93 Table ZA.2 - System of attestation of conformity94 Table ZA.
19、3 - Assignment of evaluation of conformity tasks for Space heating in residential buildings with possible supply of hot water under system 3 94 Figures Figure 1 - Flue draught values27 Figure A.1 - Example of installation of an appliance with vertical flue outlet in the test assembly.71 Figure A.2 -
20、 Example of installation of an appliance with horizontal flue outlet in the test assembly.72 Figure A.3 - View of trihedron showing general arrangement of side walls and test hearth73 Figure A.4 Details of filler pieces for trihedron rear wall74 Figure A.5 - Cross section showing trihedron construct
21、ion75 Figure A.6 - Plan view of trihedron hearth and walls showing position of measurement points76 Figure A.7 - Details of thermocouples in trihedron wall77 Figure A.8 - Construction and general arrangement of measurement section78 Figure A.9 - Details and dimensions of measurement section for vert
22、ical flue outlet79 Figure A.10 - Details and dimensions of measurement section for horizontal flue outlet80 Figure A.11 - Example of test installation for appliances with water circuit81 Figure A.12 - Dimensions of measurement section for natural draught safety test 82 Figure A.13 - Test assembly of
23、 Kachelfen or Putzfen inset appliances for heating tests83 Figure A.14 - Test surround for Kachelfen or Putzfen inset appliances.84 Figure A.15 - Example of installation with trihedron test wall and ceiling85 Figure B.1 - Flow chart showing selection process for tests on recommended fuels87 Figure Z
24、A.1 - Example CE marking information.97 Page 3 Foreword This European Standard has been prepared by Technical Committee CEN/TC 295 “Residential solid fuel burning appliances“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 13229 2001 A2 2004
链接地址:https://www.31doc.com/p-3741151.html