BS-EN-2144-1993.pdf
《BS-EN-2144-1993.pdf》由会员分享,可在线阅读,更多相关《BS-EN-2144-1993.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2144:1994 Rivets, solid, universal head, in aluminium alloy 2117, inch based series The European Standard EN 2144:1994 has the status of a British Standard UDC 621.884.2-034.715:629.7 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:25:39 GMT+00:00 20
2、06, Uncontrolled Copy, (c) BSI BS EN 2144:1994 This British Standard, having been prepared under the direction of the Aerospace Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 December 1994 BSI 11-1999 The following BSI references rela
3、te to the work on this standard: Committee reference ACE/12 Draft for comment 93/712077 DC ISBN 0 580 22626 3 Cooperating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the
4、 following countries: AustriaOesterreichisches Normungsinstitut BelgiumInstitut belge de normalisation DenmarkDansk Standardiseringsraad FinlandSuomen Standardisoimisliito, r.y. FranceAssociation franaise de normalisation GermanyDeutsches Institut fr Normung e.V. GreeceHellenic Organization for Stan
5、dardization IcelandTechnological Institute of Iceland IrelandNational Standards Authority of Ireland ItalyEnte Nazionale Italiano di Unificazione LuxembourgInspection du Travail et des Mines NetherlandsNederlands Normalisatie-instituut NorwayNorges Standardiseringsforbund PortugalInstituto Portugus
6、da Qualidade SpainAsociacin Espaola de Normalizacin y Certificacin SwedenStandardiseringskommissionen i Sverige SwitzerlandAssociation suisse de normalisation United KingdomBritish Standards Institution Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun,
7、na, Fri Nov 03 02:25:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2144:1994 BSI 11-1999i Contents Page Cooperating organizationsInside front cover National forewordii Foreword2 1Scope3 2Normative references3 3Required characteristics3 4Designation5 5Marking5 6Technical specification5 National
8、 annex NA (informative) Committees responsibleInside back cover National annex NB (informative) Cross-referencesInside back cover Figure 13 Figure 25 Table 14 Table 24 Table 35 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:25:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2144:1994
9、ii BSI 11-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN 2144:1994 Aerospace series Rivets, solid, universal head, in aluminium alloy 2117, inch based series published by the Eur
10、opean Committee for Standardization (CEN). EN 2144:1994 was produced as a result of international discussions in which the United Kingdom took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for the
11、ir correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. This standard h
12、as been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:25:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPIS
13、CHE NORM EN 2144 July 1994 UDC 621.884.2-034.715:629.7 Descriptors: Aircraft industry, full rivets, round head rivets, aluminium alloy, dimensions, designation, marking English version Aerospace series Rivets, solid, universal head, in aluminium alloy 2117, inch based series Srie arospatiale Rivets
14、ordinaires, tte ronde aplatie, en alliage daluminium 2117, srie base inches Luft- und Raumfahrt Vollniete, mit Universalkopf, aus Aluminiumlegierung 2117, Inch-Reihe This European Standard was approved by CEN on 1994-07-27. CEN members are bound to comply with the CEN/CENELEC Internal Regulations wh
15、ich stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European St
16、andard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national st
17、andards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung C
18、entral Secretariat: rue de Stassart 36, B-1050 Brussels 1994 Copyright reserved to CEN members Ref. No. EN 2144:1994 E Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 02:25:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2144:1994 BSI 11-1999 2 Foreword This European Standard has been prepar
19、ed by the European Association of Aerospace Manufacturers (AECMA). After enquiries and votes carried out in accordance with the rules of this Association, this standard has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, pri
20、or to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 1995, and conflicting national standards shall be withdrawn at the latest by January 1995. In accordance with
21、 the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy:
22、 sheffieldun sheffieldun, na, Fri Nov 03 02:25:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2144:1994 BSI 11-19993 1 Scope This standard specifies the characteristics of solid rivets, with universal head, inch based series, in aluminium alloy, for maximum operating temperature 120 C. 2 Normative
23、 references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 2144 1993
链接地址:https://www.31doc.com/p-3741393.html