BS-EN-13736-2003.pdf
《BS-EN-13736-2003.pdf》由会员分享,可在线阅读,更多相关《BS-EN-13736-2003.pdf(50页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13736:2003 Safety of machine tools Pneumatic presses The European Standard EN 13736:2003 has the status of a British Standard ICS 25.120.10 ? BS EN 13736:2003 This British Standard, was published under the authority of the Standards Policy and Strategy Committee on 23 October
2、2003 BSI 23 October 2003 ISBN 0 580 42814 1 National foreword This British Standard is the official English language version of EN 13736:2003. The UK is obliged to publish EN 13736:2003 as a British Standard (BS EN 13736:2003). However, attention is drawn to the fact that during the development of t
3、his European Standard the United Kingdom has consistently voted against its approval as an EN. The UK believes that the standard is deficient in certain safety requirements compared with the state of the art for these machines in the UK. The standard fails to satisfy some of the relevant essential r
4、equirements of the EC Machinery Safety Directive (98/37/EC), as implemented in the UK by the Supply of Machinery (Safety) Regulations 1992 (as amended), which it claims to meet. As part of BSIs duty of care we draw attention to users of BS EN 13736:2003 of our concern that the standard contains inad
5、equate requirements for protection of personnel against access to the danger zone at manually loaded/unloaded machines as specified in Annex IV to the Directive. The concerns relate specifically to clauses 5.3.2 and 5.3.3 in so far as the use of a two-hand control device(s) is concerned. When these
6、devices are provided as the sole safeguard they do not adequately control the risks to other workers. BSI will assume no liability whatsoever for any failure on the part of any user of this standard to consider these aspects. The UK participation in its preparation was entrusted by Technical Committ
7、ee MTE/1, Machine tools, to Subcommittee MTE/1/1, Metal forming machine tools, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publi
8、cations referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the nec
9、essary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the int
10、erpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 47 and a back cover. The BSI c
11、opyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13736 January 2003 ICS 25.120.10 English version Safety of machine tools - Pneumatic presses Scurit d
12、es machines-outils - Presses pneumatiquesSicherheit von Werkzeugmaschinen - Pneumatische Pressen This European Standard was approved by CEN on 15 November 2002. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
13、the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German
14、). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finlan
15、d, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stas
16、sart, 36 B-1050 Brussels 2003 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13736:2003 E EN 13736:2003 (E) 2 Contents page Foreword3 Introduction.4 1Scope 4 2Normative references 5 3Terms and definitions, abbreviations6 4List of s
17、ignificant hazards.10 5Safety requirements and/or protective measures12 6Verification of the safety requirements and/or protective measures.29 7Information for use 34 Annex A (normative) Calculation of minimum safety distances.37 Annex B (normative) Closed tools39 Annex C (informative) Examples and
18、principles of pneumatic press and power interlocking40 Annex D (informative) Electro-sensitive protective equipment (ESPE) using active opto-electronic protective devices (AOPDs)44 Annex E (normative) Conditions for noise measurement of pneumatic presses .45 Annex ZA (informative) Relationship of th
19、is standard with EC Directives.46 Bibliography47 EN 13736:2003 (E) 3 Foreword This document (EN 13736:2003) has been prepared by Technical Committee CEN/TC 143 Machine tools Safety“, the secretariat of which is held by SNV. This European Standard shall be given the status of a national standard, eit
20、her by publication of an identical text or by endorsement, at the latest by July 2003, and conflicting national standards shall be withdrawn at the latest by July 2003. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, an
21、d supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. Organisation contributing to the preparation of this European Standard include the European Manufacturer Association CECIMO. NOTEThe safe
22、ty requirements related to the use of PES or PPS will be dealt with at its next revision. The European Standards produced by CEN/TC 143 are particular to machine-tools and complement the relevant A and B standards on the subject of general safety (see introduction of EN 292-1:1991 for a description
23、of A, B and C standards). Annexes A, B and E are normative. Annexes C and D are informative. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Fi
24、nland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovalia, Spain, Sweden, Switzerland and the United Kingdom. EN 13736:2003 (E) 4 Introduction This European Standard has been prepared to be a harmonized standard to provide one means
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 13736 2003
链接地址:https://www.31doc.com/p-3741789.html