BS-EN-165000-1-1996.pdf
《BS-EN-165000-1-1996.pdf》由会员分享,可在线阅读,更多相关《BS-EN-165000-1-1996.pdf(56页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 165000-1:1996 Harmonized system of quality assessment for electronic components Film and hybrid integrated circuits Part 1: Generic specification Capability approval procedure The European Standard EN 165000-1:1996 has the status of a British Standard ICS 31.200 Licensed Copy:
2、 sheffieldun sheffieldun, na, Fri Nov 17 08:29:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 165000-1:1996 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15
3、October 1996 BSI 11-1998 The following BSI references relate to the work on this standard: Committee reference EPL/47/1 Draft for comment 92/216398 DC ISBN 0 580 26183 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee EPL
4、/47, Semiconductors, to Subcommittee EPL/47/1, Film and hybrid integrated circuits, upon which the following bodies were represented: Federation of the Electronics Industry Ministry of Defence National Supervising Inspectorate (BSI Product Certification) Amendments issued since publication Amd. No.D
5、ateComments Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 17 08:29:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 165000-1:1996 BSI 11-1998i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN 165000-15 List of referencesInside back cover Licens
6、ed Copy: sheffieldun sheffieldun, na, Fri Nov 17 08:29:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 165000-1:1996 ii BSI 11-1998 National foreword This British Standard has been prepared by Subcommittee EPL/47/1 and is the English language version of EN 165000-1:1996, Film and hybrid integrat
7、ed circuits Part 1: Generic specification. Capability approval procedure published by the European Committee for Electrotechnical Standardization (CENELEC). Cross-references Publication referred toCorresponding British Standard BS EN 165000 Film and hybrid integrated circuits EN 165000-2:1996BS EN 1
8、65000-2:1996 Internal visual inspection and special tests EN 165000-3:1996BS EN 165000-3:1996 Self-audit checklist and report for film and hybrid integrated circuit manufacturers EN 165000-4:1996BS EN 165000-4:1996 Customer information, product assessment level schedules and blank detail specificati
9、on IEC 50BS 4727 Glossary of electrotechnical, power, telecommunication, electronics, lighting and colour terms EN 60068 Environmental testing EN 60068-1:1994 (IEC 68-1:1988) BS EN 60068-1:1995 General and guidance IEC 68-2BS EN 60068-2 Test methods EN 60068-2-1:1993 (IEC 68-2-1:1990) BS EN 60068-2-
10、1:1993 Tests A. Cold EN 60068-2-2:1993 (IEC 68-2-2:1974) BS EN 60068-2-2:1993 Tests B. Dry heat BS 2011 Environmental testing Part 2.1 Tests HD 323.2.3 S2:1987 (IEC 68-2-3:1969) Part 2.1Ca:1977 Test Ca. Damp heat, steady state BS EN 60068 Environmental testing BS EN 60068-2 Test methods EN 60068-2-6
11、:1995 (IEC 68-2-6:1995) BS EN 60068-2-6:1996 Test Fc. Vibration (sinusoidal) EN 60068-2-7:1993 (IEC 68-2-7:1983) BS EN 60068-2-7:1993 Test Ga and guidance. Acceleration, steady state BS 2011 Environmental testing Part 2.1 Tests HD 323.2.11 S1:1988 (IEC 68-2-11:1981) Part 2.1Ka:1982 Test Ka. Salt mis
12、t HD 323.2.14 S2:1987 (IEC 68-2-14:1984) Part 2.1N:1985 Test N. Change of temperature BS EN 60068 Environmental testing BS EN 60068-2 Test methods EN 60068-2-17:1994 (IEC 68-2-17:1994) BS EN 60068-2-17:1995 Test Q. Sealing BS 2011 Environmental testing Part 2.1 Tests Licensed Copy: sheffieldun sheff
13、ieldun, na, Fri Nov 17 08:29:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 165000-1:1996 BSI 11-1998iii HD 323.2.20 S3:1988 (IEC 68-2-20:1979) Part 2.1T:1981 Test T. Soldering HD 323.2.21 S3:1988 (IEC 68-2-21:1983) BS 2011:Part 2.1U:1984 Test U. Robustness of terminations and integral mounting
14、 devices BS EN 60068 Environmental testing BS EN 60068-2 Test methods EN 60068-2-27:1993 (IEC 68-2-27:1987) BS EN 60068-2-27:1993 Environmental testing procedures. Tests. Test Ea and guidance. Shock BS 2011 Environmental testing Part 2.2 Guidance IEC 68-2-28:1990Part 2.2C Part 3: Self-audit checklis
15、t and report for film and hybrid integrated circuit manufacturers; Part 4: Customer information, product assessment level schedules and blank detail specification. Part 3 is primarily intended as a pro-forma for the manufacturer and is not considered essential for a customer in this form. Part 4 is
16、considered an essential document for all users; in particular it includes a helpful introductory section which is aimed at potential customers and seeks to explain the underlying philosophy upon which the whole standard is based. Contents Page Foreword2 1General5 1.1Scope5 1.2Normative references5 1
17、.3Units, symbols and terminology7 1.4Standard and preferred values9 1.5Marking9 2Quality assessment procedures9 2.1General9 2.1.1Eligibility for capability approval9 2.1.2Primary stage of manufacture9 2.1.3Subcontracting9 2.1.4Control of procurement sources and incoming material10 2.1.5Validity of r
18、elease for delivery10 2.1.6Rework10 2.2Procedures for capability approval11 2.2.1Application for capability approval11 2.2.2Granting of capability approval11 2.2.3Description of capability11 2.2.4Capability qualifying components12 2.2.5Demonstration and verification of capability12 2.2.6Procedures t
19、o be followed in the event of CQC failures15 2.2.7Abstract of description of capability15 2.3Procedures following the granting of capability approval15 2.3.1Maintenance of capability approval15 2.3.2Notification of changes likely to affect the validity of capability approval15 2.4Release for deliver
20、y16 2.4.1General16 2.4.2Quality conformance inspection requirements16 2.4.3Detail specification17 2.4.3(1)General17 2.4.3(2)Customer detail specification17 2.4.3(3)Detail specification for standard catalogue circuits to be included in the Qualified Products List (QPL)17 3Test and measurement procedu
21、res 18 3.1General18 3.2Standard conditions for testing18 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement(dop) 1997-03-01 latest date by which the national standards conflicting with the EN have to be withdrawn(dow
22、) 1997-03-01 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 17 08:29:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 165000-1:1996 BSI 11-19983 Page 3.3Visual inspections and package dimensions20 3.4Electrical measurement procedures20 3.5Environmental test procedures21 Figure 1 Definition of a
23、xis for mechanical and other tests19 Figure 2 Pulling force for bond strength test43 Figure 3 Apparatus requirements for the added component bond strength destructive test48 Table 1 Severities for damp heat, steady-state, Method 223 Table 2 Severities for damp heat, steady-state, Method 325 Table 3
24、Preferred conditions for shock27 Table 4 Parameters for sealing test, Method 131 Table 5 “Preheat” times34 Table 6 Minimum pulling force42 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 17 08:29:55 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 4 blank Licensed Copy: sheffieldun sheffieldun, na, Fr
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 165000 1996
链接地址:https://www.31doc.com/p-3741854.html