BS-EN-2002-2-2005.pdf
《BS-EN-2002-2-2005.pdf》由会员分享,可在线阅读,更多相关《BS-EN-2002-2-2005.pdf(26页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2002-2:2005 Metallic materials Test methods Part 2: Tensile testing at elevated temperature The European Standard EN 2002-2:2005 has the status of a British Standard ICS 49.025.05; 49.025.15 ? Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:42 GMT
2、+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2002-2:2005 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 3 January 2006 BSI 3 January 2006 ISBN 0 580 47229 9 National foreword This British Standard is the official English language version of
3、 EN 2002-2:2005. The UK participation in its preparation was entrusted by Technical Committee ACE/61, Metallic materials for aerospace purposes, to Subcommittee ACE/61/-/6, Mechanical testing of metallic materials, which has the responsibility to: aid enquirers to understand the text; present to the
4、 responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained
5、on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of th
6、e BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary
7、 of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 23 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffie
8、ldun sheffieldun, na, Fri Nov 03 01:33:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2002-002 November 2005 ICS 49.025.05; 49.025.15 English Version Aerospace series - Metallic materials - Test methods - Part 2: Tensile testing at elevated tempera
9、ture Srie arospatiale - Matriaux mtalliques - Mthodes dessais applicables - Partie 2 : Essais de traction temperature leve Luft- und Raumfahrt - Metallische Werkstoffe - Prfverfahren - Teil 2: Zugversuch bei Hochtemperatur This European Standard was approved by CEN on 19 September 2005. CEN members
10、are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application t
11、o the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same
12、status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slo
13、venia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2005 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN
14、 national Members. Ref. No. EN 2002-002:2005: E Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 2 Contents Page Foreword 3 Introduction4 1 Scope.4 2 Normative references .4 3 Terms, definitions and symbols 4 4 Health and safety 7 5 Principle
15、.7 6 Testing requirements7 7 Test report.14 Annex A (normative) Types of test piece to be used for sheet and strip with thickness less than or equal to 8 mm .16 Annex B (normative) Types of non-machined test piece to be used in the case of bar, section and wire with a diameter or thickness less than
16、 or equal to 8 mm.18 Annex C (normative) Types of machined test piece to be used in the case of bar, section, plate and wire with diameter or thickness greater than 8 mm and for forgings and castings.19 Annex D (normative) Types of test piece to be used in the case of tubes.22 EN 2002-2:2005 License
17、d Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:42 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 3 Foreword This European Standard (EN 2002-002:2005) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in a
18、ccordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publicat
19、ion of an identical text or by endorsement, at the latest by May 2006, and conflicting national standards shall be withdrawn at the latest by May 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not b
20、e held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, Fra
21、nce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2002-2:2005 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:42 GMT+00:00 2006, U
22、ncontrolled Copy, (c) BSI 4 Introduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. 1 Scope This standard specifies the requirements for the tensile testing of metallic materials a
23、t elevated temperature for aerospace applications. It shall be applied when referred to in the EN technical specification or material standard unless otherwise specified on the drawing, order or inspection schedule. 2 Normative references The following referenced documents are indispensable for the
24、application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 7500-1, Metallic materials Verification of static uniaxial testing machines Part 1: Tension/ compressio
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 2002 2005
链接地址:https://www.31doc.com/p-3741898.html