《BS-EN-2591-404-1998.pdf》由会员分享,可在线阅读,更多相关《BS-EN-2591-404-1998.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2591-404:1998 Elements of electrical and optical connection Test methods Part 404: Transverse load The European Standard EN 2591-404:1998 has the status of a British Standard ICS 49.060 Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:03:03 GMT+00:00
2、2006, Uncontrolled Copy, (c) BSI BS EN 2591-404:1998 This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 November 1998 BSI 05-1999 ISBN 0 580 30710 7 National for
3、eword This British Standard is the English language version of EN 2591-404:1998. The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic, electrical and fibre optic technology, to Subcommittee ACE/6/3, Aerospace connectors, which has the responsibility t
4、o: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of orga
5、nizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Sta
6、ndards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Stan
7、dard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 and 3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporat
8、ed. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:03:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2591-404:1998 BSI 05-1999i Contents Page National for
9、ewordInside front cover Foreword2 Text of EN 2591-4043 Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:03:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:03:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORM
10、E EUROPENNE EUROPISCHE NORM EN 2591-404 August 1998 ICS 49.060 Descriptors: Aircraft industry, aircraft equipment, connecting equipment, test English version Aerospace series Elements of electrical and optical connection Test methods Part 404: Transverse load Srie arospatiale Organes de connexion le
11、ctrique et optique Mthodes dessais Partie 404: Charge transversale Luft- und Raumfahrt Elektrische und optische Verbindungselemente Prfverfahren Teil 404: Querkraft This European Standard was approved by CEN on 23 February 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulatio
12、ns which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This Europe
13、an Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the nation
14、al standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches
15、 Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2591-404:1998 E Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:03:03 GMT+00:00 2006, Uncon
16、trolled Copy, (c) BSI EN 2591-404:1998 BSI 05-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of th
17、e National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 1999, and conflicting
18、 national standards shall be withdrawn at the latest by February 1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany
19、, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 1Scope3 2Normative references3 3Preparation of specimens3 4Method3 Figure 1 Example of test set-up3 Licensed Copy: sheffieldun sheffieldun, na, Thu
20、 Nov 02 18:03:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2591-404:1998 BSI 05-19993 1 Scope This standard specifies a method of assessing the ability of elements of connection to withstand transverse loads without mechanical or electrical damage. It shall be used together with EN 2591. 2 Norma
21、tive references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of a
22、ny of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 2591, Aerospace series Elements of electrical and optical connection Test methods General. EN 2591-101,
23、 Aerospace series Elements of electrical and optical connection Test methods Part 101: Visual examination. EN 2591-204, Aerospace series Elements of electrical and optical connection Test methods Part 204: Discontinuity of contacts in the microsecond range. EN 2591-205, Aerospace series Elements of
24、electrical and optical connection Test methods Part 205: Housing (shell) electrical continuity. EN 2591-408, Aerospace series Elements of electrical and optical connection Test methods Part 408: Mating and unmating forces1). 3 Preparation of specimens 3.1 Specimens shall be mated and peripheral cont
25、acts shall be wired in series. The receptacle shall be mounted on a rigid support (see Figure 1). The plug shall be fitted with a specified accessory or adaptor. 3.2 Unless specified in the technical specification, the following details shall be stated: type of plug accessory or adaptor; point of lo
26、ad application; load and distance between support and point of application; final measurements (if applicable). 4 Method 4.1 Procedure The load shall be applied parallel to the mounting plate. It shall be increased at a rate not exceeding 45 N/s until the specified value is reached, then maintained
27、for 1 min. Measurements according to EN 2591-204 (Method B) shall be carried out throughout the test. If specified, measurements according to EN 2591-205 shall be carried out throughout the test. No discontinuity greater than 1 4s shall be observed. 4.2 Final measurements (if applicable) The specime
28、ns shall be subjected to the following test sequence: EN 2591-101; EN 2591-408. 1) Published as AECMA Prestandard at the date of publication of this standard Figure 1 Example of test set-up Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:03:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS
29、EN 2591-404:1998 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions
30、British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguit
31、y while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers au
32、tomatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply
33、the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI
34、electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase
35、 price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Exce
36、pt as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in
37、the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 18:03:03 GMT+00:00 2006, Uncontrolled Copy, (c) BSI
链接地址:https://www.31doc.com/p-3741931.html