《BS-EN-40-6-2002.pdf》由会员分享,可在线阅读,更多相关《BS-EN-40-6-2002.pdf(26页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 40-6:2002 Lighting columns Part 6: Requirements for aluminium lighting columns The European Standard EN 40-6:2002 has the status of a British Standard ICS 77.150.10; 93.080.40 ? BS EN 40-6:2002 This British Standard, having been prepared under the direction of the Building and
2、 Civil Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 17 July 2002 BSI 17 July 2002 ISBN 0 580 40083 2 National foreword This British Standard is the official English language version of EN 40-6:2002. It supersede
3、s BS EN 40-6:2000 which is withdrawn. EN 40-6:2002 is a candidate “harmonized” European Standard and fully takes into account the requirements of the European Commission mandate M/111, Circulation fixtures, given under the EU Construction Products Directive (89/106/EEC), and intended to lead to CE m
4、arking. The date of applicability of EN 40-6:2002 as a “harmonized” European Standard, i.e. the date after which this standard may be used for CE marking purposes, is subject to an announcement in the Official Journal of the European Communities. EN 40-6:2002 is the subject of transitional arrangeme
5、nts agreed under the European Commission mandate. The Member States have agreed a nominal transition period for the co-existence of EN 40-6:2002 and their corresponding national standard(s). It is intended that this period will comprise a nominal nine month period during which any required changes t
6、o national regulations are to be made, followed by a further nominal twelve month period for the implementation of CE marking. At the end of this co-existence period, the national standard(s) will be withdrawn. In the UK, there are no corresponding national standards. The UK participation in its pre
7、paration was entrusted by Technical Committee B/509, Road equipment, to Subcommittee B/509/50, Road equipment Street lighting columns, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British S
8、tandards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.
9、This publication does not purport to include all the necessary provisions of a contract. Users are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible
10、 international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, th
11、e EN title page, pages 23 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 40-6 April 2002 ICS 77.150.10; 93.080.40Supersedes
12、 EN 40-6:2000 English version Lighting columns - Part 6: Requirements for aluminium lighting columns Candlabres dclairage public - Partie 6: Exigences pour les candlabres dclairage public en aluminium Lichtmaste - Teil 6: Anforderungen fr Lichtmaste aus Aluminium This European Standard was approved
13、by CEN on 25 February 2002. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national st
14、andards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to
15、 the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and
16、 United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2002 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 40-6:2
17、002 E EN 40-6:2002 (E) 2 Contents page Foreword3 1Scope4 2Normative references4 3Terms and definitions5 4Materials6 5Dimensions6 6Design and design verification6 7Welding6 8Joints7 9Protection against mechanical impact7 10Internal finish and sharp edges8 11Corrosion protection8 12Marking9 13Conformi
18、ty control9 14Acceptance criteria13 15Re-testing14 16Performance under vehicle impact Passive safety15 Annex A (informative) Corrosion protection for aluminium lighting columns16 Annex B (informative) Recommendations for storage and installation17 Annex C (normative) Initial type tests18 Annex ZA (i
19、nformative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive19 EN 40-6:2002 (E) 3 Foreword This document EN 40-6:2002 has been prepared by Technical Committee CEN/TC 50 “Lighting columns and spigots“, the secretariat of which is held by BSI. This
20、European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2002, and conflicting national standards shall be withdrawn at the latest by January 2004. This document supercedes EN 40-6:2000. This document h
21、as been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association and supports essential requirements of EU Directive 89/106/EEC. For relationship with EU Directive 89/106/EEC see informative annex ZA which is an integral part of this document. In this
22、standard the annexes A and B are informative and the annex C is normative. Wherever reference is made to classes, they are considered to be technical classes and not classes according to 3(2) of the Construction Products Directive. This European Standard is the sixth in a series relating to specific
23、ations for lighting columns. At present the Parts of this standard are as follows: Part 1: Definitions and terms Part 2: General requirements and dimensions Part 3: Design and verification 3-1:Specification for characteristic loads 3-2:Verification by testing 3-3:Verification by calculation Part 4:
24、Requirements for reinforced and prestressed concrete lighting columns Part 5: Requirements for steel lighting columns Part 6: Requirements for aluminium lighting columns Part 7: Requirements for fibre reinforced polymer composite lighting columns According to the CEN/CENELEC Internal Regulations, th
25、e national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, EN 40-6:2002 (E) 4 Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switz
26、erland and the United Kingdom. 1 Scope This European Standard specifies requirements for aluminium lighting columns. It includes materials and conformity control. It applies to post top columns not exceeding 20 m height for post top lanterns and to columns with brackets not exceeding 18 m height for
27、 side entry lanterns. This European Standard specifies performance related to the essential requirements of resistance to horizontal (wind) loads and performance under vehicle impact (passive safety) in support of the Essential Requirement No 4 Safety in use measured according to the corresponding t
28、est methods included in this European Standard or available in separate European Standards. It provides for the evaluation of conformity of the products to this European Standard. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publica
29、tions. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision
30、. For undated references the latest edition of the publication referred to applies (including amendments). EN 40-1Lighting columns - Part 1: Definitions and terms. prEN 40-2:1999Lighting columns - Part 2: General requirements and dimensions. EN 40-3-1Lighting columns - Design and verification - Part
31、 3-1: Specification for characteristic loads. EN 40-3-2Lighting columns - Design and verification - Part 3-2: Verification by testing. prEN 40-3-3Lighting columns - Design and verification - Part 3-3: Verification by calculation. EN 288-1Specification and approval of welding procedures for metallic
32、materials Part 1: General rules for fusion welding. EN 288-2Specification and approval of welding procedures for metallic materials Part 2: Welding procedures specification for arc welding. EN 40-6:2002 (E) 5 EN 288-4Specification and approval of welding procedures for metallic materials Part 4: Wel
33、ding procedure tests for the arc welding of aluminium and its alloys. EN 288-8Specification and approval of welding procedures for metallic materials Part 8: Approval by a pre-production welding test. EN 485-3Aluminium and aluminium alloys - Sheet, strip and plates -Part 3: Tolerances on shape and d
34、imensions for hot rolled products. EN 485-4Aluminium and aluminium alloys - Sheet, strip and plates Part 4: Tolerances on shape and dimensions for cold rolled products. EN 571-1Non-destructive testing Penetrant testing General principles. EN 755-7Aluminium and aluminium alloys - Extruded rod/bar, tu
35、be and profiles - Part 7: Seamless tubes, tolerances on dimension and form. EN 755-8Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form. EN 970Non-destructive examination of fusion welds - Visual examination. EN 1011-1Weldi
36、ng - Recommendations for welding of metallic materials General guidance for arc welding. EN 1011-4Welding - Recommendations for welding of metallic materials - Arc welding of aluminium and aluminium alloys. EN 1706Aluminium and aluminium alloys - Castings - Chemical composition and mechanical proper
37、ties. EN 10025Hot rolled products of non-alloy structural steels - Technical delivery conditions. EN 10204Metallic products - Types of inspection documents. EN 12767Passive safety of support structures for road equipment Requirements and test methods. EN 50102Degrees of protection provided by enclos
38、ures for electrical equipment against external mechanical impacts (IK code). 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN 40-1 apply. EN 40-6:2002 (E) 6 4 Materials 4.1 Aluminium Materials used shall comply with one of the following standa
39、rds: EN 485-3, EN 485-4, EN 755-7, EN 755-8 and EN 1706. Electrolytic action between the foundation bolts and the flange plate shall be prevented by insulation or physical separation. 4.2 Foundation bolts The minimum mechanical properties of the steel used for foundation bolts shall comply with the
40、requirements of EN 10025 grade S 235 JR. 5 Dimensions Dimensions shall be in accordance with prEN 40-2. 6 Design and design verification The column shall be designed to sustain safely the dead loads and the wind loads specified in EN 40-3-1. The structural design of a lighting column shall be verifi
41、ed either by calculation in accordance with prEN 40-3-3 or by testing in accordance with EN 40-3-2. 7 Welding 7.1 Welding process Arc welding of aluminium and its alloys shall be in accordance with EN 1011-1 and prEN 1011-4. 7.2 Welding procedures Welding procedures shall comply with EN 288-1 and EN
42、 288-2. Written procedures shall be provided for the main structural joints which shall include where relevant the flange plate joint, the base compartment to shaft joint, the door reinforcement, any intermediate column joint, the column to bracket joint and the column seam weld when this is carried
43、 out at the time of column manufacture. EN 40-6:2002 (E) 7 Welding procedures shall be approved in accordance with EN 288-8. Pre-production test pieces shall represent the main structural joints. Welding procedures shall be verified by testing to the requirements of EN 288-4. The welding consumables
44、 and procedures used shall be such that the mechanical properties of the as- deposited weld metal will not be less than the respective minimum values required by the designers specifications for the parent metal to be welded. Verification shall be by a welding co-ordinator. Procedures shall be revie
45、wed and reapproved where necessary after a period of seven years. 7.3 Welding personnel Welders shall be tested for each approved procedure to which they shall be required to work (see 7.2). Test pieces shall be as used in the original procedure tests. The approval range shall be in accordance with
46、that for the original procedure. 8 Joints 8.1 General All joints shall be designed to the requirements specified in clause 6. NOTE Design of joint details should avoid moisture retention and corrosion. 8.2 Friction joints When joints are made by drawing parts together to form a friction joint the ad
47、ditional stresses in the connection shall be included in the design. 8.3 Welded joints Welded joints shall comply with the requirements of clause 7. 9 Protection against mechanical impact A type test shall be carried out on each type of column base, or part, provided that each end of the part extend
48、s at least 0,3 m above and below the door opening. The test shall comply with an impact protection category of IK08 as specified in EN 50102 with the door fitted. The test equipment shall be either impact pendulum hammer or vertical free fall hammer. The number of impacts shall be five and shall be
49、applied around the circumference at the mid height of the door. For circular columns these shall be equi-spaced around the remaining circumference excluding the door. For octagonal columns these shall be on each of the adjacent faces excluding the door. EN 40-6:2002 (E) 8 After testing there shall be no indentation greater than 3 mm in depth when measured with a profile gauge. The test validates those products of which the outside diameter (or flat dimension) is equal to o
链接地址:https://www.31doc.com/p-3742089.html