《BS-EN-423-2002.pdf》由会员分享,可在线阅读,更多相关《BS-EN-423-2002.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 423:2002 Resilient floor coverings Determination of resistance to staining The European Standard EN 423:2001 has the status of a British Standard ICS 97.150 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 423:2002 This British Standard, having been
2、 prepared under the direction of the Sector Policy and Strategy Committee for Materials and Chemicals, was published under the authority of the Standards Policy and Strategy Committee on 25 February 2002 BSI 25 February 2002 ISBN 0 580 39123 X National foreword This British Standard is the official
3、English language version of EN 423:2001. It supersedes BS EN 423:1993 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRI/60, Resilient floor coverings, which has the responsibility to: A list of organizations represented on this committee can be obta
4、ined on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” f
5、acility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obl
6、igations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This
7、 document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROP
8、ISCHE NORM EN 423 December 2001 ICS 97.150Supersedes EN 423:1993 English version Resilient floor coverings - Determination of resistance to staining Revtements de sol rsilients - Dtermination de rsistance aux taches Elastische Bodenbelge - Bestimmung der Fleckenempfindlichkeit This European Standard
9、 was approved by CEN on 18 November 2001. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning su
10、ch national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language a
11、nd notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerl
12、and and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN
13、 423:2001 E EN 423:2001 (E) 2 Foreword This European Standard has been prepared by Technical Committee CEN/TC 134 “Resilient and textile floor coverings“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an ide
14、ntical text or by endorsement, at the latest by June 2002, and conflicting national standards shall be withdrawn at the latest by June 2002. This European Standard supersedes EN 423:1993. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countri
15、es are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. EN 423:2001 (E) 3 1 Scope This European Standard speci
16、fies a method for determining the resistance of a resilient floor covering to those chemical substances it is likely to experience in service. 2 Principle Various chemical substances in liquid or paste form are placed on a test piece for defined periods and removed. After cleaning has been carried o
17、ut the resulting change of appearance is assessed under specified lighting conditions. 3 Apparatus and materials 3.1 Standard laboratory equipment a) pipettes; b) spatulas. 3.2 Untreated glass fibre fabric, of mass per unit area (300 to 400) g/m2 and diameter approximately 40 mm. 3.3 Chemical substa
18、nces in liquid or paste form, to be agreed between the interested parties. 3.4 Standard cleaning and stain removal products. 3.4.1 White cotton, in pad or cloth form. 3.4.2 Brushes, hard, unlikely to score the surface. 3.4.3 Warm water, used alone or with the following: a) synthetic detergent, e.g.
19、sodium alkylsulfate; b) soap; c) alkaline products, e.g. washing soda or ammonia solution; d) hydrogen peroxide; e) sodium hypochlorite; f) sodium thiosulfate, 1 % solution; g) oxalic acid. EN 423:2001 (E) 4 3.4.4 Denatured ethanol 3.4.5 White spirit 3.4.6 Turpentine 3.5 Abrasives Abrasive scouring
20、pads, steel wool No. 00 or scouring powder, or abrasive papers, grain size P 240 or finer, used with water. 3.6 Special cleaning products, special products, recommended by the floor covering manufacturer. 3.7 Illumination device, comprising a lamp of correlated colour temperature 5 500 K to 6 500 K,
21、 mounted to give an intensity of light at the viewing platform of (1500 100) lx and in such a way as to illuminate the test piece vertically from above. The surroundings shall be neutral and darkened. The intensity of the light shall be checked frequently by the use of a luxometer. The lifetime of t
22、he lamp, as given by the manufacturer, shall not be exceeded. 3.8 Rotary viewing table, enabling the test piece to be rotated so that it may be viewed from all directions under the standard illumination. 4 Sampling and preparation of test pieces Take a representative sample from the available materi
23、al. Take one test piece in the colour(s) to be used with a surface area of at least 3 000 mm2 for each stain to be tested. If the test uses a substance likely to cause swelling or deformation of the test piece, e.g. prolonged contact with a solvent, bond the test piece to a fibre-cement sheet at lea
24、st five days before testing. Subject the test piece to any treatment required, e.g. light abrasion to remove surface polish or application of a non-specified maintenance product. Identify the positions corresponding to each of the substances used, either by marking numbers on the test piece (using a
25、 marking which is not affected by the material used in the test), or by a sketch, diagram or photograph. 5 Procedure 5.1 Application of liquid substances Place the fabric (3.2) on the surface of the test specimen and saturate it with 1 ml to 2 ml of the test liquid. Leave the fabric in place for the
26、 duration of the test. 5.2 Application of paste substances With a spatula, spread about 1 000 mm3 over an area of 300 mm2 to 400 mm2, (i.e. thickness 2,5 mm to 3 mm). 5.3 Duration of contact The main duration of contact shall be 2 h. If a stain appears on the test piece after 2 h, a new test shall b
27、e conducted for a period of 30 min. EN 423:2001 (E) 5 5.4 Types of cleaning and observation 5.4.1Before cleaning, remove stains that are still liquid with cotton, working from the edge towards the centre of the stain. Scrape off the remains of paste with a spatula and wipe with cotton as above. Afte
28、r cleaning has been carried out, examine the residual staining from a distance of approximately 800 mm at an approximate angle of 45o and from all directions by slowly rotating the viewing table. 5.4.2If a stain is visible, rub it down with a mild abrasive material or a cleaning product recommended
29、by the manufacturer, and examine as described in 5.4.1. NOTEIf white spirit or turpentine are used, these should be rinsed off with denatured ethanol. 6 Expression of results Express the results in accordance with Table 1. Table 1 Interpretation and presentation of results IndexEffect of the test af
30、ter cleaning/abrasion 0Not affected 1Very slightly affected 2Slightly affected 3Affected 4Severely affected 7 Test report The test report shall contain the following information: a) a reference to this standard, i.e. EN 423; b) a complete identification of the product tested, including type, source,
31、 colour and manufacturers reference numbers; c) previous history of the sample; d) the staining materials, type of cleaning and contact periods used; e) the test results in accordance with Table 1; f) any deviation from this standard which may have affected the results. BS EN 423:2002 BSI 389 Chiswi
32、ck High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated b
33、y amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Stan
34、dard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive
35、 the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi
36、-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standa
37、rds through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing me
38、mbers of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regardi
39、ng online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the
40、 international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BS
41、I. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.
链接地址:https://www.31doc.com/p-3742223.html