BS-EN-4300-2008.pdf
《BS-EN-4300-2008.pdf》由会员分享,可在线阅读,更多相关《BS-EN-4300-2008.pdf(22页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 4300:2008 Aerospace series Identification marking of engine items Design standard ICS 49.050 ? Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:32:58 MDTNo reproductio
2、n or networking permitted without license from IHS -,-,- BS EN 4300:2008 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 May 2008 BSI 2008 ISBN 978 0 580 60984 8 National foreword This British Standard is the UK implementation of EN 4300:2
3、008. The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provi
4、sions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication DateComments Copyright British Standards Institution Provided by IHS under license with BSI - Uncon
5、trolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:32:58 MDTNo reproduction or networking permitted without license from IHS -,-,- EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4300 April 2008 ICS 49.050 English Version Aerospace series - Identification marking of engine
6、 items - Design standard Srie arospatiale - Marquage pour articles moteurs - Normes de conception Luft- und Raumfahrt - Kennzeichnung von Triebwerkbauteilen - Konstruktionsnorm This European Standard was approved by CEN on 29 February 2008. CEN members are bound to comply with the CEN/CENELEC Intern
7、al Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN membe
8、r. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN member
9、s are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Sw
10、itzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref.
11、No. EN 4300:2008: E Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:32:58 MDTNo reproduction or networking permitted without license from IHS -,-,- 2 Contents Page Foreword3 1 Scope 4 2 Nor
12、mative references4 3 Abbreviation.4 4 Presentation.4 4.1 Definition 4 4.2 Marking.5 4.3 Relationship between identifier and mark 5 5 Application of use5 5.1 General5 5.2 Selection of the marks (see Table 3)6 5.3 Selection of the marking locations7 5.4 Selection of the marking processes7 6 Informatio
13、n to be entered on the drawing.8 6.1 General8 6.2 Definition of the item.8 6.3 Location of indication marks9 6.4 Automatic identification methods10 BS EN 4300:2008 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for
14、 Resale, 08/14/2008 20:32:58 MDTNo reproduction or networking permitted without license from IHS -,-,- 3 Foreword This document (EN 4300:2008) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accord
15、ance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of
16、an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at the latest by October 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not
17、be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, F
18、inland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 4300:2008 Copyright British Standards Institution Provided by IHS unde
19、r license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:32:58 MDTNo reproduction or networking permitted without license from IHS -,-,- 4 1 Scope This standard: describes the location and the layout of the marks of the item; describes the marking processes
20、to be used according to the environment and the function of the items; determines the selection conditions of the marks; determines the compatibility conditions of the marking processes with the constitution, the production and the use of the items. This document applies to aerospace engine items an
21、d shall be used in conjunction with EN 4301. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any am
22、endments) applies. EN 4301, Aerospace series Identification marking methods for engine items. AS 478J, Identification Marking Methods. 1) 3 Abbreviation O.C.R. Optical Character Recognition 4 Presentation 4.1 Definition 4.1.1 Identity mark An identity is represented by a mark affixed by means of a m
23、arking process. An identity mark allows for example: the identity of an item and its design origin; the initial compliance of the item with its definition to be proved; the data relating to the various stages of the items life in production and in use to be traced (traceability); the conditions of u
24、se to be specified; etc. 4.1.2 Description of an identity mark An identity mark is information (coded identity or not), consisting of characters presented in a clear and orderly manner. A mark is characterised by a composition and a size and is applied directly to the item or to a separate support.
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 4300 2008
链接地址:https://www.31doc.com/p-3742246.html