BS-EN-474-3-1996.pdf
《BS-EN-474-3-1996.pdf》由会员分享,可在线阅读,更多相关《BS-EN-474-3-1996.pdf(26页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 474-3:1996 Earth-moving machinery Safety Part 3: Requirements for loaders The European Standard EN 474-3:1996 has the status of a British Standard ICS 53.100 BS EN 474-3:1996 This British Standard, having been prepared under the direction of the Sector Board for Building and C
2、ivil Engineering, was published under the authority of the Standards Board and comes into effect on 15 July 1996 BSI 02-1999 The following BSI references relate to the work on this standard: Committee reference B/513/1 Draft for comment 93/102261 DC ISBN 0 580 25868 8 Committees responsible for this
3、 British Standard The preparation of this British Standard was entrusted by Technical Committee B/513, Construction equipment and plant, and site safety, to Subcommittee B/513/1, Earth-moving machinery, upon which the following bodies were represented: British Coal Corporation Construction Plant (Hi
4、re Association) Federation of Civil Engineering Contractors Federation of Manufacturers of Construction Equipment and Cranes Health and Safety Executive Institution of Civil Engineers Silsoe Research Institute Amendments issued since publication Amd. No.DateComments BS EN 474-3:1996 BSI 02-1999i Con
5、tents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN 474-35 List of referencesInside back cover BS EN 474-3:1996 ii BSI 02-1999 National foreword This British Standard has been prepared by Subcommittee B/513/1 and is the English language version of EN 474-3:19
6、96 Earth-moving machinery Safety Part 3: Requirements for loaders, published by the European Committee for Standardization (CEN). It is one of a number of British Standards implementing European Standards on machinery safety matters, in the development of which the United Kingdom has played an activ
7、e part. This British Standard covers the essential safety requirements in the Machinery Directive (89/392/EEC) and the Amending Directive (91/368/EEC). Cross-references Publication referred toCorresponding British Standard BS EN 292 Safety of machinery Basic concepts, general principles for design E
8、N 292-1:1991Part 1:1991 Basic terminology, methodology EN 292-2:1991Part 2:1991 Technical principles and specifications EN 294:1992BS EN 294:1992 Safety of machinery Safety distances to prevent danger zones being reached by the upper limbs EN 474-1:1995BS EN 474 Earth-moving machinery Safety Part 1:
9、1995 General requirements ENV 1070:1993DD ENV 1070:1993 Safety of machinery Terminology EN 23411:1988BS 5538:1983 Specification for minimum operator space envelope for earth-moving machinery EN 25353:1988BS 5631:1978 Specification for earth-moving machinery and tractors and machinery for agriculture
10、 and forestry Seat index point EN 60204-1:1992BS EN 60204 Safety of machinery Electrical equipment of machines Part 1:1993 Specification for general requirements ISO 2330:1995BS 5639 Fork arms for fork lift trucks Part 4:1978 Specification for technical characteristics and testing ISO 2867:1994BS 69
11、12 Safety of earth-moving machinery Part 15:1995 Specification for access systems ISO 3164:1992Part 7:1992 Specification for laboratory evaluations or roll-over and falling object protective structures: the deflection-limiting volume for earth-moving machinery ISO 3449:1992Part 6:1992 Specification
12、for falling object protective structures on earth-moving machinery: laboratory tests ISO 3457:1986BS EN ISO 3457:1995 Earth-moving machinery Guards and shields Definitions and specifications ISO 3471:1994BS 6912 Safety of earth-moving machinery Part 14:1995 Specification for laboratory tests and per
13、formance requirements of roll-over protective structures ISO 4250-2:1991BS AU 50 Tyres and wheels Part 1: Tyres Section 3: Off-the-road tyres Subsection 3.2a:1991 Specification for narrow and wide base tyre loads and inflation pressures ISO 5006-1:1991BS 6911 Testing earth-moving machinery Part 5:19
14、92 Determination of operators field of view ISO 5998:1986BS 6912 Safety of earth-moving machinery Part 2:1989 Specification for rated operating load for crawler and wheel loaders BS EN 474-3:1996 BSI 02-1999iii A British Standard does not purport to include all the necessary provisions of a contract
15、. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. ISO 6014:1986BS 5982:1987 Method for determination of ground speed of earth-moving machinery ISO 6016:1982BS 6300:1982 Methods of
16、measuring the masses of whole machines, their equipment and components of earth-moving machinery ISO 6393:1985BS 6812 Airborne noise emitted by earth-moving machinery Part 1:1987 Method of measurement of exterior noise in a stationary test condition ISO 6682:1986BS EN ISO 6682:1995 Earth-moving mach
17、inery Zones of comfort and reach for control ISO 6683:1981BS 6218:1981 Specification for performance requirements for seat belts and seat belt anchorages for earth-moving machinery fitted with roll-over protective structures ISO 7096:1994BS 6912 Safety of earth-moving machinery Part 17:1995 Specific
18、ation for laboratory evaluation of operator seat vibration ISO 7131:1984BS 6685:1986 Glossary of terms for loaders used for earth-moving ISO 7546:1983BS 6422:1983 Method for volumetric rating of loader and front loading excavator buckets used for earth-moving ISO 8313:1989BS 6911 Testing earth-movin
19、g machinery Part 2:1990 Measurement of tool forces and tipping loads of loaders ISO 10533:1993BS 6912 Safety of earth-moving machinery Part 11:1993 Requirements for lift arm support devices Summary of pages This document comprises a front cover, an inside front cover, pages i to iv, the EN title pag
20、e, pages 2 to 18, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. iv blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 474-3 February
21、 1996 ICS 53.100 Descriptors: Earth-moving equipment, loaders, safety of machine, accident prevention, safety requirements, specifications English version Earth-moving machinery Part 3: Requirements for loaders Engins de terrassement Scurit Partie 3: Exigences applicables aux chargeuses Erdbaumaschi
22、nen Sicherheit Teil 3: Anforderungen fr Lader This European Standard was approved by CEN on 1995-11-03. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
23、 Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
24、under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Neth
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 474 1996
链接地址:https://www.31doc.com/p-3742757.html