BS-EN-485-2-2004.pdf
《BS-EN-485-2-2004.pdf》由会员分享,可在线阅读,更多相关《BS-EN-485-2-2004.pdf(52页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 485-2:2004 Aluminium and aluminium alloys Sheet, strip and plate Part 2: Mechanical properties The European Standard EN 485-2:2004 has the status of a British Standard ICS 77.150.10 ? BS EN 485-2:2004 This British Standard was published under the authority of the Standards Pol
2、icy and Strategy Committee on 14 July 2004 BSI 14 July 2004 ISBN 0 580 44060 5 National foreword This British Standard is the official English language version of EN 485-2:2004. It supersedes BS EN 485-2:1995 which is withdrawn. The UK participation in its preparation was entrusted by Technical Comm
3、ittee NFE/35, Light metals and their alloys, to Subcommittee NFE/35/5, Wrought aluminium and aluminium alloys, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement
4、 international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does no
5、t purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European co
6、mmittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 t
7、o 49 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments -,-,- EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 485-2 July 2004 ICS 77.150.10Supersedes EN 485-2:1994 English v
8、ersion Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties Aluminium et alliages daluminium - Tles, bandes et tles paisses - Partie 2: Caractristiques mcaniques Aluminium und Aluminiumlegierungen - Bnder, Bleche und Platten - Teil 2: Mechanische Eigenschaften This
9、 European Standard was approved by CEN on 24 March 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical reference
10、s concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into i
11、ts own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lu
12、xembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CENAll rights of
13、 exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 485-2:2004: E -,-,- EN 485-2:2004 (E) 2 Contents Foreword4 1 Scope 6 2 Normative references6 3 Tensile test.6 4 Bend test.7 5 Hardness test.7 Table 1 Minimum material gauge and Brinell hardness values
14、 8 6 Electrical conductivity.8 7 Stress-corrosion resistance.8 8 Exfoliation corrosion resistance (5xxx series alloys)9 9 Exfoliation corrosion resistance (7xxx series alloys)9 Table 2 Aluminium EN AW-1080A Al 99,8(A) 12 Table 3 Aluminium EN AW-1070A Al 99,7 .13 Table 4 Aluminium EN AW-1050A Al 99,5
15、 .14 Table 5 Aluminium EN AW-1200 Al 99,015 Table 6 Alloy EN AW-2014 Al Cu4SiMg.16 Table 7 Alloy EN AW-2014A Al Cu4SiMg(A)17 Table 8 Alloy EN AW-2017A Al Cu4MgSi(A)18 Table 9 Alloy EN AW-2024 Al Cu4Mg1.19 Table 10 Alloy EN AW-3003 Al Mn1Cu.20 Table 11 Alloy EN AW-3103 Al Mn121 Table 12 Alloy EN AW-3
16、004 Al Mn1Mg122 Table 13 Alloy EN AW-3005 Al Mn1Mg0,5.23 Table 14 Alloy EN AW-3105 Al Mn0,5Mg0,524 Table 15 Alloy EN AW-4006 Al Si1Fe.25 Table 16 Alloy EN AW-4007 Al Si1,5Mn.25 Table 17 Alloy EN AW-4015 Al Si2Mn26 Table 18 Alloy EN AW-5005 Al Mg1(B), alloy EN AW-5005A Al Mg1(C).27 Table 19 Alloy EN
17、AW-5040 Al Mg1,5Mn.28 Table 20 Alloy EN AW-5049 Al Mg2Mn0,8.29 Table 21 Alloy EN AW-5449 Al Mg2Mn0,8(B)30 Table 22 Alloy EN AW-5050 Al Mg1,5(C) .31 Table 23 Alloy EN AW-5251 Al Mg232 Table 24 Alloy EN AW-5052 Al Mg2,5 33 Table 25 Alloy EN AW-5154A Al Mg3,5(A).34 Table 26 Alloy EN AW-5454 Al Mg3Mn35
18、EN 485-2:2004 (E) 3 Table 27 Alloy EN AW-5754 Al Mg3 .36 Table 28 Alloy EN AW-5182 Al Mg4,5Mn0,437 Table 29 Alloy EN AW-5083 Al Mg4,5Mn0,738 Table 30 Alloy EN AW-5383 Al Mg4,5Mn0,939 Table 31 Alloy EN AW-5086 Al Mg4 .40 Table 32 Alloy EN AW-6016 Al Si1,2Mg0,441 Table 33 Alloy EN AW-6061 Al Mg1SiCu.4
19、1 Table 34 Alloy EN AW-6082 Al Si1MgMn.42 Table 35 Alloy EN AW-7020 Al Zn4,5Mg143 Table 36 Alloy EN AW-7021 Al Zn5,5Mg1,5.44 Table 37 Alloy EN AW-7022 Al Zn5Mg3Cu44 Table 38 Alloy EN AW-7075 Al Zn5,5MgCu.45 Table 38 (concluded)46 Table 39 Alloy EN AW-8011A Al FeSi(A) .47 Annex A (normative) Rules fo
20、r rounding48 Bibliography49 -,-,- EN 485-2:2004 (E) 4 Foreword This document (EN 485-2:2004) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, eithe
21、r by publication of an identical text or by endorsement, at the latest by January 2005, and conflicting national standards shall be withdrawn at the latest by January 2005. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 7 “Sheet, strip and plate“ to prepare the
22、following standard: EN 485-2, Aluminium and aluminium alloys Sheet, strip and plate Part 2: Mechanical properties. This standard is part of a set of four standards. The other standards deal with: Part 1: Technical conditions for inspection and delivery Part 3: Tolerances on dimensions and form for h
23、ot-rolled products Part 4: Tolerances on shape and dimensions for cold-rolled products This document supersedes EN 485-2:1994. Besides very slight editorial adjustments in the text and update of normative references, the following technical changes have been made: Clause 1: NOTE added. Clause 2: AST
24、M G34-86 changed into ASTM G34-97 ASTM G66-86 changed into ASTM G66-95 Clause 5: Note added Tables 2 to 39: Due to the introduction of new alloys, the tables have been renumbered when necessary. New alloys: EN AW-2014A, 4015, 5005A, 5449, 5383, 6016. Modified values or extended ranges: EN AW-1070A:
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 485 2004
链接地址:https://www.31doc.com/p-3742797.html