BS-EN-60317-0-3-2008.pdf
《BS-EN-60317-0-3-2008.pdf》由会员分享,可在线阅读,更多相关《BS-EN-60317-0-3-2008.pdf(24页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 60317-0-3:2008 Specifications for particular types of winding wires Part 0-3: General requirements Enamelled round aluminium wire ICS 29.060.10 ? Licensed CopyChinese University of Hong Kong, 21/10/2008 03:53, Uncontrolled Copy, (c) BSI BS EN 60317-0-3:2008 This British Standa
2、rd was published under the authority of the Standards Policy and Strategy Committee on 30 September 2008 BSI 2008 ISBN 978 0 580 56284 6 National foreword This British Standard is the UK implementation of EN 60317-0-3:2008. It is identical to IEC 60317-0-3:2008. It supersedes BS EN 60317-0-3:1998 wh
3、ich is withdrawn. The UK participation in its preparation was entrusted to Technical Committee GEL/55, Winding wires. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a cont
4、ract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication DateComments Licensed CopyChinese University of Hong Kong, 21/10/2008 03:53, Uncontrolled Copy, (c) BSI EUROPEAN S
5、TANDARD EN 60317-0-3 NORME EUROPENNE EUROPISCHE NORM August 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC -
6、All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60317-0-3:2008 E ICS 29.060.10 Supersedes EN 60317-0-3:1998 + A1:2000 + A2:2004 English version Specifications for particular types of winding wires - Part 0-3: General requirements - Enamelle
7、d round aluminium wire (IEC 60317-0-3:2008) Spcifications pour types particuliers de fils de bobinage - Partie 0-3: Exigences gnrales - Fil de section circulaire en aluminium maill (CEI 60317-0-3:2008) Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten - Teil 0-3: Allgemeine Anforderun
8、gen - Runddrhte aus Aluminium, lackisoliert (IEC 60317-0-3:2008) This European Standard was approved by CENELEC on 2008-06-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national stand
9、ard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any othe
10、r language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republ
11、ic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed CopyChinese University of Hong Kong, 21/
12、10/2008 03:53, Uncontrolled Copy, (c) BSI Foreword The text of document 55/1056/FDIS, future edition 3 of IEC 60317-0-3, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60317-0-3 on 2008-06-01. This European Standard supersedes E
13、N 60317-0-3:1998 + A1:2000 + A2:2004. Technical changes from EN 60317-0-3:1998 include a clarification of the appearance requirements, revisions of the wire size ranges applicable to the flexibility and adherence tests, an indication that pin hole test requirements are under consideration. This stan
14、dard is to be read in conjunction with the EN 60851 series. The clause numbers used in this part of EN 60317 are identical with the respective test numbers of EN 60851. In case of inconsistencies between EN 60851 and this EN 60317-0-3, the latter shall prevail. The following dates were fixed: latest
15、 date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-03-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-06-01 Annex ZA has been added by CENELEC. _ Endorsemen
16、t notice The text of the International Standard IEC 60317-0-3:2008 was approved by CENELEC as a European Standard without any modification. _ 2 BS EN 60317-0-3:2008 Licensed CopyChinese University of Hong Kong, 21/10/2008 03:53, Uncontrolled Copy, (c) BSI CONTENTS 1 2 3 3.1 3.2 3.3 4 4.1 4.2 4.3 4.3
17、.1 4.3.2 4.4 4.4.1 4.4.2 5 6 7 8 8.1 Mandrel winding test (nominal conductor diameters up to and including 1,600 8.2 8.3 8.4 9 9.1 9.2 10 11 12 13 14 Continuity of insulation (nominal conductor diameters up to and including 15 16 17 3 BS EN 60317-0-3:2008 INTRODUCTION.5 Scope.6 Normative references6
18、 Terms, definitions and general notes on methods of tests and appearance6 Definitions .6 General notes on methods of test 7 Appearance.8 Dimensions.8 Conductor diameter .8 Out of roundness of conductor.10 Minimum increase in diameter due to the insulation and the bonding layer10 Enamelled wires with
19、out a bonding layer 10 Enamelled wires with a bonding layer.10 Maximum overall diameter.10 Enamelled wires without a bonding layer 10 Enamelled wires with a bonding layer.10 Electrical resistance11 Elongation 11 Springiness.11 Flexibility and adherence 11 mm).11 Stretching test (nominal conductor di
20、ameters over 1,000 mm)11 Jerk test (nominal conductor diameters up to and including 1,000 mm) 12 Peel test (nominal conductor diameters over 1,000 mm) 12 Heat shock .12 Nominal conductor diameters up to and including 1,600 mm 12 Nominal conductor diameters over 1,600 mm.12 Cut-through 12 Resistance
21、to abrasion .12 Resistance to solvents12 Breakdown voltage .12 13.1 General .12 13.2 Nominal conductor diameters up to and including 2,500 mm 13 13.3 Nominal conductor diameters over 2,500 mm.13 1,600 mm)14 Temperature index14 Resistance to refrigerants.14 Solderability14 Licensed CopyChinese Univer
22、sity of Hong Kong, 21/10/2008 03:53, Uncontrolled Copy, (c) BSI 18 19 20 21 23 30 4 BS EN 60317-0-3:2008 Heat or solvent bonding 14 Dielectric dissipation factor .14 Resistance to transformer oil 14 Loss of mass 15 Pin hole test .15 Packaging 15 Annex A (informative) Dimensions for intermediate nomi
23、nal conductor diameters (R 40).16 Annex B (informative) Method for the calculation of linear resistance18 Annex C (informative) Resistance 19 Bibliography20 Table 1 Dimensions of enamelled wires (R 20) .9 Table 2 Dimensions of enamelled wires with a bonding layer (R 20)10 Table 3 Elongation .11 Tabl
24、e 4 Mandrel winding.11 Table 5 Heat shock 12 Table 6 Breakdown voltage 13 Table 7 Breakdown voltage 13 Table 8 Continuity of insulation.14 Table A.1 Dimensions of enamelled wires (R 40) 16 Table A.2 Dimensions of enamelled wires with a bonding layer (R 40).17 Table C.1 Electrical resistances .19 Ann
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 60317 2008
链接地址:https://www.31doc.com/p-3743273.html