BS-EN-61086-1-1995 IEC-61086-1-1992.pdf
《BS-EN-61086-1-1995 IEC-61086-1-1992.pdf》由会员分享,可在线阅读,更多相关《BS-EN-61086-1-1995 IEC-61086-1-1992.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 61086-1:1995 IEC 1086-1: 1992 Specification for Coatings for loaded printed wire boards (conformal coatings) Part 1: Definitions, classification and general requirements The European Standard EN 61086-1:1994 has the status of a British Standard Licensed Copy: sheffieldun sheff
2、ieldun, na, Fri Nov 10 16:29:49 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 61086-1:1995 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 March 1995 BSI 01-1
3、999 The following BSI references relate to the work on this standard: Committee reference CIL/15 Special announcement in BSI News December 1994 ISBN 0 580 23744 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee CIL/15, In
4、sulating materials, upon which the following bodies were represented: British Ceramic Research Ltd. British Industrial Ceramic Manufacturers Association British Telecommunications plc Department of Trade and Industry (National Measurement Accreditation Service) Electrical and Electronic Insulation A
5、ssociation (BEAMA Ltd.) Electricity Association Federation of Electronics Industry Ministry of Defence Rotating Electrical Machines Association (BEAMA Ltd.) Transmission and Distribution Association (BEAMA Ltd.) The following body was also represented in the drafting of the standard, through subcomm
6、ittees and panels: Adhesive Tape Manufacturers Association Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 16:29:49 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 61086-1:1995 BSI 01-1999i Contents Page Committees responsibleInside fr
7、ont cover National forewordii Foreword2 Introduction3 1Scope3 2Normative reference3 3Definition3 4Classification3 5General requirements4 Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications5 Table 13 List of reference
8、sInside back cover Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 16:29:49 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 61086-1:1995 ii BSI 01-1999 National foreword This British Standard has been prepared under the direction of the Electrotechnical Sector Board and is the English langua
9、ge version of EN 61086-1:1994 Specification for coatings for loaded printed wire boards (conformal coatings) Part 1: Definitions, classification and general requirements published by the European Committee for Electrotechnical Standardization (CENELEC). It is identical with IEC 1086-1:1992 published
10、 by the International Electrotechnical Commission (IEC). BS EN 61086-1 and BS EN 61086-2 partially supersede BS 5917:1980. BS EN 61086-3-1 is currently in preparation. When BS EN 61086-3-1 is published BS 5917:1980 will be superseded and will be withdrawn. A British Standard does not purport to incl
11、ude all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference Publication referred toCorresponding British Standard HD 323.1.S2:19
12、88BS 2011 Environmental testing (IEC 68-1:1988)Part 1.1:1989 General and guidance EN 61086-2:1994 (IEC 1086-2:1992) BS EN 61086 Specification for coatings for loaded printed wire boards (conformal coatings) Part 2:1995 Methods of test Summary of pages This document comprises a front cover, an inside
13、 front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun shef
14、fieldun, na, Fri Nov 10 16:29:49 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61086-1 August 1994 ICS 29.040.20;01.040.29 Descriptors: Printed-circuit cards, printed-circuit boards, wiring, coatings, electrical insulating materials, definitions, cla
15、ssification, specifications, marking English version Specification for coatings for loaded printed wire boards (conformal coatings) Part 1: Definitions, classification and general requirements (IEC 1086-1:1992) Spcification pour les revtements appliqus sur les cartes de cblage imprimes et dotes de c
16、omposants conventionnels (revtements enrobants) Partie 1: Dfinitions, classification et prescriptions gnrales (CEI 1086-1:1992) Bestimmung fr beschichtungen fr bestckte Leiterplatten (conformal coatings) Teil 1: Begriffe, Einteilung und allgemeine Anforderungen (IEC 1086-1:1992) This European Standa
17、rd was approved by CENELEC on 1994-05-15. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concernin
18、g such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its
19、own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, S
20、weden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1994 Copyright reserved to CENELEC members
21、Ref. No. EN 61086-1:1994 E Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 16:29:49 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 61086-1:1994 2 BSI 01-1999 Foreword The CENELEC questionnaire procedure, performed for finding out whether or not the International Standard IEC 1086-1:1992 could
22、be accepted without textual changes, has shown that no common modifications were necessary for the acceptance as a European Standard. The reference document was submitted to CENELEC members for formal vote and was approved by CENELEC as EN 61086-1 on 15 May 1994. The following dates were fixed: Anne
23、xes designated “normative” are part of the body of the standard. In this standard, annex ZA is normative. latest date of publication of an identical national standard(dop) 1995-03-15 latest date of withdrawal of conflicting national standards(dow) 1995-03-15 Licensed Copy: sheffieldun sheffieldun, n
24、a, Fri Nov 10 16:29:49 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 61086-1:1994 BSI 01-19993 Introduction This International Standard forms an element of a series which deals with coatings for loaded printed wire boards (conformal coatings). The series consists of three parts: Part 1: Definitions,
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-EN-61086-1-1995 IEC-61086-1-1992 BS EN 61086 1995 IEC 1992
链接地址:https://www.31doc.com/p-3743578.html