BS-EN-61212-1-1996.pdf
《BS-EN-61212-1-1996.pdf》由会员分享,可在线阅读,更多相关《BS-EN-61212-1-1996.pdf(14页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 61212-1:1996 Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Part 1: General requirements The European Standard EN 61212-1:1995 has the status of a British Standard Product code 00659282 ICS 29.040.20 Licensed Copy: sheffie
2、ldun sheffieldun, na, Thu Nov 09 15:15:00 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 61212-1:1996 This British Standard, having been prepared under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 1
3、5 January 1996 BSI 03-1999 The following BSI references relate to the work on this standard: Committee reference PRI/77 Draft for comment 92/47761 DC ISBN 0 580 25197 7 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PRI/
4、77, Rigid laminated sheets, tubes and rods, for industrial purposes, upon which the following bodies were represented: Electrical and Electronic Insulation Association (BEAMA Ltd.) Federation of the Electronics Industry Ministry of Defence Rotating Electrical Machines Association (BEAMA Ltd.) Amendm
5、ents issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 09 15:15:00 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 61212-1:1996 BSI 03-1999i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN 61212-13 List
6、of referencesInside back cover Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 09 15:15:00 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 61212-1:1996 ii BSI 03-1999 National foreword This British Standard has been prepared by Technical Committee PRI/77 and is the English language version of E
7、N 61212-1:1995 Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Part 1: General requirements, published by the European Committee for Standardization (CEN). EN 61212-1:1995 was produced as a result of international discussions in which the United
8、Kingdom took an active part. BS EN 61212 consists of the following parts: Part 1: General requirements; Part 2: Methods of test; Part 3: Specification for individual materials: Sheet 1 Round laminated rolled tubes; Sheet 2 Round laminated moulded tubes; Sheet 3 Round laminated moulded rods. This Par
9、t of BS EN 61212 partially supersedes Part 1 of BS 6128:1981. Together, Parts 1 and 2 of BS EN 61212 supersede entirely BS 6128-1:1981 which is withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their c
10、orrect application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred toCorresponding British Standard EN 61212-3:1995 (IEC 1212-3:1995) BS EN 61212 Industrial rigid round laminated tubes rods based on thermosetting re
11、sins for electrical purposes Part 3:1996 Specifications for individual materials ISO 472:1988BS ISO 472:1988 Plastics. Vocabulary Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 8, an inside back cover and a back cover. Thi
12、s standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 09 15:15:00 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROP
13、ENNE EUROPISCHE NORM EN 61212-1 May 1995 ICS 29.040.20 Descriptors: Electrical insulating materials, solid electrical insulating materials, tubes, metal bars, laminates, thermosetting resins, tests English version Industrial rigid round laminated tubes and rods based on thermosetting resins for elec
14、trical purposes Part 1: General requirements (IEC 1212-1:1995) Tubes et barres industriels, rigides, ronds, stratifis, base de rsines thermodurcissables, usages lectriques Partie 1: Prescriptions gnrales (CEI 1212-1:1995) Runde Rohre und Stbe aus technischen Schichtprestoffen auf der Basis wrmehrtba
15、rer Harze fr elektrotechnische Zwecke Teil 1: Allgemeine Anforderungen (IEC 1212-1:1995) This European Standard was approved by CENELEC on 1994-07-05. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the st
16、atus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German
17、). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, F
18、inland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische
19、 Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1995 Copyright reserved to CENELEC members Ref. No. EN 61212-1:1995 E Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 09 15:15:00 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 61212-1:1995 BSI 03-1999 2 Foreword The text of docume
20、nt 15C(CO)333, future edition 1 of IEC 1212-1, prepared by SC 15C, Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61212-1 on 1994-07-05. The following dates were fixed: Annexes designated “normative” are part of th
21、e body of the standard. In this standard, Annex ZA is normative. Annex ZA has been added by CENELEC. Contents Page Foreword2 Introduction3 1General3 2Definitions3 3Designations and abbreviations3 4General requirements Appearance4 5Conditions of supply4 Annex ZA (normative) Normative references to in
22、ternational publications with their corresponding European publications8 Table 1 Types of industrial laminated round rolled tubes5 Table 2 Types of industrial laminated round moulded tubes6 Table 3 Types of industrial laminated round moulded rods7 latest date by which the EN has to be implemented at
23、 national level by publication of an identical national standard or by endorsement(dop) 1996-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn(dow) 1996-04-01 Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 09 15:15:00 GMT+00:00 2006, Uncontrolled Cop
24、y, (c) BSI EN 61212-1:1995 BSI 03-19993 Introduction This International Standard is one of a series which deals with industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes. This series consists of three parts: Part 1: General requirements (IEC 1212-1);
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 61212 1996
链接地址:https://www.31doc.com/p-3743636.html