BS-EN-62026-1-2007.pdf
《BS-EN-62026-1-2007.pdf》由会员分享,可在线阅读,更多相关《BS-EN-62026-1-2007.pdf(18页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 62026-1:2007 Low-voltage switchgear and controlgear Controller-device interfaces (CDIs) Part 1: General rules The European Standard EN 62026-1:2007 has the status of a British Standard ICS 29.130.20 ? Licensed Copy: London South Bank University, London South Bank University, F
2、ri Nov 16 07:32:56 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS EN 62026-1:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2007 BSI 2007 ISBN 978 0 580 56435 2 National foreword This British Standard is the UK implementation
3、of EN 62026-1:2007. It is identical to IEC 62026-1:2007. The UK participation in its preparation was entrusted by Technical Committee PEL/17, Switchgear, controlgear, and HV-LV co-ordination, to Subcommittee PEL/17/2, Low voltage switchgear and controlgear. A list of organizations represented on thi
4、s committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued sin
5、ce publication Amd. No. DateComments Licensed Copy: London South Bank University, London South Bank University, Fri Nov 16 07:32:56 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD EN 62026-1 NORME EUROPENNE EUROPISCHE NORM September 2007 CENELEC European Committee for Electrotechnical S
6、tandardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 62026-
7、1:2007 E ICS 29.130.20 English version Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 1: General rules (IEC 62026-1:2007) Appareillage basse tension - Interfaces appareil de commande-appareil (CDI) - Partie 1: Rgles gnrales (CEI 62026-1:2007) Niederspannungsschal
8、tgerte - Steuerungs-Gerte-Netzwerke (CDIs) - Teil 1: Allgemeine Festlegungen (IEC 62026-1:2007) This European Standard was approved by CENELEC on 2007-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
9、 the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French,
10、 German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bul
11、garia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Lon
12、don South Bank University, London South Bank University, Fri Nov 16 07:32:56 GMT+00:00 2007, Uncontrolled Copy, (c) BSI Foreword The text of document 17B/1505/CDV, future edition 2 of IEC 62026-1, prepared by SC 17B, Low-voltage switchgear and controlgear, of IEC TC 17, Switchgear and controlgear, w
13、as submitted to the IEC-CENELEC parallel Unique Acceptance Procedure and was approved by CENELEC as EN 62026-1 on 2007-09-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2
14、008-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2010-09-01 This European Standard has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association and covers essential requirements of EC Dir
15、ectives EMC (89/336/EEC) and EMC2 (2004/108/EC). See Annex ZZ. Annexes ZA and ZZ have been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 62026-1:2007 was approved by CENELEC as a European Standard without any modification. _ EN 62026-1:2007 2 Licensed Copy: London
16、 South Bank University, London South Bank University, Fri Nov 16 07:32:56 GMT+00:00 2007, Uncontrolled Copy, (c) BSI CONTENTS INTRODUCTION.4 1 Scope.5 2 Normative references5 3 Terms and definitions .6 4 Classifications 7 5 Characteristics7 5.1 CDI components7 5.2 Interfaces 7 5.3 Topology .8 5.4 In
17、formation exchanges.8 5.5 Attributes.8 6 Product information.8 6.1 Instructions for installation, operation and maintenance8 6.2 Profiles8 6.3 Marking .8 6.4 Degree of protection 9 7 Normal service, mounting and transport conditions9 7.1 General .9 7.2 Normal service conditions9 7.2.1 General .9 7.2
18、.2 Ambient air temperature.9 7.2.3 Altitude9 7.2.4 Climatic conditions.9 7.3 Conditions during transport and storage.9 7.4 Mounting .10 8 Constructional and performance requirements 10 8.1 General .10 8.2 Electromagnetic compatibility (EMC)10 8.2.1 Immunity10 8.2.2 Emission11 8.2.3 EMC tests11 9 Tes
19、ts11 9.1 General .11 9.2 Type tests .11 9.3 Electromagnetic compatibility.11 Table 1 Immunity requirements 10 EN 62026-1:2007 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications .13 Annex ZZ (informative) Coverage of Essential Requ
20、irements of EC Directives .14 Licensed Copy: London South Bank University, London South Bank University, Fri Nov 16 07:32:56 GMT+00:00 2007, Uncontrolled Copy, (c) BSI INTRODUCTION The class of controller-device interfaces (CDIs) covered in this International Standard includes industrial CDIs for co
21、ntrol systems, factory automation and process automation. Industrial CDIs have proliferated to meet specific user needs, but no single CDI meets all needs. The reason for multiple solutions is the wide range of physical, usage, information content and configuration requirements. The physical require
22、ments have resulted in CDIs with widely differing signal and line conditioning mechanisms in order to meet distance, node count and environmental considerations. While there is wide variation in CDI technologies, there are common components, interfaces and environmental requirements that are specifi
23、ed by this standard. Standardized definitions of these common CDI requirements assist the user to compare and select technologies to match the distance, node count, throughout and installation requirements for a specific application. This standard simplifies the CDI selection process by providing a
24、common structure for generating a specific CDIs IEC standard while also allowing specific interface features and capabilities to be included. Clauses 1 to 8 contain the outline of general requirements that the CDIs IEC standard identifies. Clause 9 contains the test specification. Standardization of
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 62026 2007
链接地址:https://www.31doc.com/p-3743892.html