《BS-EN-845-1-2003.pdf》由会员分享,可在线阅读,更多相关《BS-EN-845-1-2003.pdf(62页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 845-1:2003 Specification for ancillary components for masonry Part 1: Ties, tension straps, hangers and brackets The European Standard EN 845-1:2003 has the status of a British Standard ICS 91.060.10; 91.080.30 ? Incorporating Corrigendum No. 1 and Amendment No. 1 Licensed Cop
2、y: sheffieldun sheffieldun, na, Tue Nov 07 06:40:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 845-1:2003 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 16 September 2003 ISBN 0 580 42606 8 National foreword This British Standard is th
3、e official English language version of EN 845-1:2003. EN 845-1 is a candidate “harmonized” European Standard and fully takes into account the requirements of the European Commission mandate M116, Masonry and related products, given under the EU Construction Products Directive (89/106/EEC), and is in
4、tended to lead to CE marking. The date of applicability of EN 845-1 as a “harmonized” European Standard, i.e. the date after which this standard may be used for CE marking purposes, is subject to an announcement in the Official Journal of the European Communities. The Commission in consultation with
5、 Member States has agreed a transition period for the co-existence of “harmonized” European Standards and their corresponding national standard(s). It is intended that this period will comprise a period, usually nine months, after the date of availability of the European Standard, during which any r
6、equired changes to national regulations are to be made, followed by a further period, usually of 12 months, for the implementation of CE marking. At the end of this co-existence period, the national standard(s) will be withdrawn. EN 845-1 is the subject of transitional arrangements agreed under the
7、Commission mandate. In the UK, the corresponding national standards are: BS 1243:1978, Specification for metal ties for cavity wall construction; BS 6178-1:1990, Joist hangers Part 1: Specification for joist hangers for building into masonry walls of domestic dwellings; DD 140-1:1986, Wall ties Part
8、 1: Methods of test for mortar joint and timber frame connections; and based on this transition period of twentyone months, the above mentioned national standards will be withdrawn in January 2005. NOTEThis date is approximate. Users of this standard should contact BSI Customer Services for confirma
9、tion of withdrawal. The UK participation in its preparation was entrusted by Technical Committee B/519, Masonry, and associated testing, to Subcommittee B/519/3, Ancillary components, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request
10、 to its secretary. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK
11、. BSI 2006 Amendments issued since publication Amd. No. DateComments 14736 Corrigendum No. 1 1 October 2003Correction to Figure 6 15539Revision of supersession details and addition of NA.5.4 29 September 2006 Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:40:58 GMT+00:00 2006, Uncontrolle
12、d Copy, (c) BSI BS EN 845-1:2003 i EN 845-1:2003 has been prepared by CEN/TC 125, Masonry, and immediately supersedes EN 845-1:2001 which is withdrawn (but see also transitional arrangements above in relation to other British Standards). EN 845-1 specifies the characteristics and performance require
13、ments for ties, joist hangers, straps and brackets available throughout the CEN member countries. It aims to do so in product performance terms, avoiding as far as possible prescriptive requirements and all the traditional designations of these products available throughout Europe. Current products,
14、 however, will continue to be manufactured, traded and used, even though they are not referred to by name in this European Standard. EN 845-1 includes clauses covering initial type tests, factory production control, sampling for initial type testing and independent testing of consignments. These are
15、 similar in all masonry product specifications. The UK National Annex NA attached to this standard provides an informative commentary on the differences between EN 845-1, BS 1243 and BS 6178-1. Nothing in this annex should be construed as specifying requirements other than those contained in the nor
16、mative parts of this European Standard. If CE marking is performed, the procedures in Annex ZA will apply. The significance of the CE marking is that the product manufacturer claims compliance with the “harmonized” requirements given in the normative text of the product standard. These relate to the
17、 essential requirements of the EU Construction Products Directive. Not all product characteristics need necessarily be given on the CE marking, but those product characteristics covered by regulations in force in each EU Member State, where the manufacturer intends that the product will be used, do
18、need to be stated. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Elec
19、tronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages
20、This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 57 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. BSI 2006 Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:40:58 G
21、MT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:40:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 845-1 April 2003 ICS 91.060.10; 91.080.30Supersedes EN 845-1:2001 English version Specifi
22、cation for ancillary components for masonry - Part 1: Ties, tension straps, hangers and brackets Spcification pour composants accessoires de maonnerie - Partie 1: Attaches, brides de fixation, triers de support et consoles Festlegungen fr Ergnzungsbauteile fr Mauerwerk - Teil 1: Maueranker, Zugbnder
23、, Auflager und Konsolen This European Standard was approved by CEN on 2 October 2002. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists
24、and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibi
25、lity of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, M
26、alta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2003 CENAll rights of exploitation in any form and
27、 by any means reserved worldwide for CEN national Members. Ref. No. EN 845-1:2003 E Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:40:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 845-1:2003 (E) 2 Contents page Foreword.3 1Scope4 2Normative references4 3Terms, definitions and symbols6
28、3.1Terms and definitions.6 3.2Symbols .9 4Materials.9 4.1General.9 4.2Fixings and materials not supplied by the manufacturer.9 5Requirements 9 5.1General.9 5.2Dimensions and limit deviations.10 5.3Mechanical strength11 5.4Resistance to water crossing a cavity14 5.5Safety during installation .14 5.6D
29、urability14 6Description and designation14 7Marking.16 8Evaluation of conformity16 8.1General.16 8.2Initial type tests.16 8.3Factory production control 17 8.4Sampling for initial type testing and independent testing of consignments17 Annex A (normative) Materials and protective coatings19 Annex B (n
30、ormative) Scheme of factory production control.24 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive 26 Bibliography .54 Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:40:58 GMT+00:00 2006, Uncontrolled Copy, (c) BS
31、I EN 845-1:2003 (E) 3 Foreword This document (EN 845-1:2003) has been prepared by Technical Committee CEN/TC 125 “Masonry“, the Secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement,
32、at the latest by October 2003, and conflicting national standards shall be withdrawn at the latest by January 2005. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association and supports the essential requirements of the
33、EU Construction Products Directive (89/106/EEC). For relationship with EU Directives, see informative Annex ZA which is an integral part of this standard. In this European Standard the Annexes A and B are normative. This document supersedes EN 845-1:2001. This Part has been modified, including the i
34、ntroduction of additional requirements, taking into account the detailed answer by CEN/TC 125 to EC mandate M116 for masonry as well as details of the relationship of this new harmonized European Standard with the EU Directives. EN 845 “Specification for ancillary components for masonry” consists of
35、 the following Parts: Part 1: Wall ties, tension straps, hangers and brackets. Part 2: Lintels. Part 3: Bed joint reinforcement of steel meshwork. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European S
36、tandard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:40:58 GMT+0
37、0:00 2006, Uncontrolled Copy, (c) BSI EN 845-1:2003 (E) 4 1 Scope This European Standard specifies requirements for wall ties, tension straps, hangers and brackets for interconnecting masonry and for connecting masonry to other parts of works and buildings including walls, floors, beams, and columns
38、. Where anchors or fasteners are supplied or specified as part of an ancillary component, the requirements including performance requirements apply to the complete product. This European Standard is not applicable to: a) anchors and fasteners other than as part of an ancillary component; b) shelf an
39、gles; c) wall starter plates for tying into existing walls; d) products formed from materials other than: 1) austenitic stainless steel (molybdenum chrome nickel alloys or chrome nickel alloys); 2) ferritic stainless steel; 3) copper; 4) phosphor bronze; 5) aluminium bronze; 6) zinc-coated-steel wit
40、h or without organic coating; 7) polypropylene; 8) polyamide (for expansion plugs only). NOTE The resistance fire performance of the products included herein cannot be assessed separately from the masonry element of which they are part and is therefore not covered under the scope of this part of thi
41、s European Standard. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent am
42、endments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 846-4, Methods of test for ancillary components for
43、 masonry Part 4: Determination of load capacity and load-deflection characteristics of straps. EN 846-5, Methods of test for ancillary components for masonry Part 5: Determination of tensile and compressive load capacity and stiffness of wall ties (couplet test). EN 846-6, Methods of test for ancill
44、ary components for masonry Part 6: Determination of tensile and compressive load capacity and stiffness of wall ties (single end test). Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 07 06:40:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 845-1:2003 (E) 5 EN 846-7, Methods of test for ancilla
45、ry components for masonry Part 7: Determination of shear load capacity and load displacement characteristics of shear ties and slip ties (couplet test for mortar joint connections). EN 846-8, Methods of test for ancillary components for masonry Part 8: Determination of load capacity and load-deflect
46、ion characteristics of joist hangers. EN 846-10, Methods of test for ancillary components for masonry Part 10: Determination of load capacity and load-deflection characteristics of brackets. EN 846-13: 2001, Methods of test for ancillary components for masonry Part 13: Determination of resistance to
47、 impact, abrasion and corrosion of organic coatings. EN 10020, Definitions and classification of grades of steel. EN 10088-1, Stainless steels Part 1: List of stainless steels. EN 10088-2, Stainless steels Part 2: Technical delivery conditions for sheet/plate and strip for general purposes. EN 10088
48、-3, Stainless steels Part 3: Technical delivery conditions for sheet/plate and strip for semi-finished products, bars, rods and sections for general purposes. EN 10142, Continuously hot-dip zinc coated low carbon steel sheet and strip for cold forming; technical delivery conditions. EN 10143:1993, C
49、ontinuously hot-dip metal coated steel sheet and strip; tolerances on dimensions and shape. EN 10147, Continuously hot-dip zinc coated unalloyed structural steel sheet and strip; technical delivery conditions. EN 10244-1, Steel wire and wire products Non-ferrous metallic coatings on steel wire Part 1: General principles. EN 10244-2, Steel wire and wire products Non-ferrous metallic coatings on steel wire Part 2: Zinc and zinc alloy coatings on steel wire. E
链接地址:https://www.31doc.com/p-3743934.html