BS-EN-ISO-10350-1-2008.pdf
《BS-EN-ISO-10350-1-2008.pdf》由会员分享,可在线阅读,更多相关《BS-EN-ISO-10350-1-2008.pdf(20页珍藏版)》请在三一文库上搜索。
1、BS EN ISO 10350-1:2008 ICS 83.080.20, NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Plastics Acquisition and presentation of comparable single- point data Part 1: Moulding materials (ISO 10350-1:2007) Licensed Copy: London South Bank University, South Bank U
2、niversity, 30/01/2009 13:48, Uncontrolled Copy, (c) BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 3ember 2008 BSI 2008 ISBN 978 0 580 54447 7 Amendments/corrigenda issued since publication DateComments BS EN ISO 10350-1:2008 National fo
3、reword This British Standard is the UK implementation of EN ISO 10350-1: 2008. It is identical to . It supersedes BS EN ISO 10350-1:2001 and which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRI/21, Testing of plastics. A list of organizations represent
4、ed on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. ISO 10350-1:
5、2008 1 Dec Licensed Copy: London South Bank University, South Bank University, 30/01/2009 13:48, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10350-1 August 2008 ICS 83.080.20Supersedes EN ISO 10350-1:2000 English Version Plastics - Acquisition and presentation
6、 of comparable single- point data - Part 1: Moulding materials (ISO 10350-1:2007) Plastiques - Acquisition et prsentation de caractristiques intrinsques comparables - Partie 1: Matriaux pour moulage (ISO 10350-1:2007) Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 1
7、: Formmassen (ISO 10350- 1:2007) This European Standard was approved by CEN on 30 July 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date
8、 lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the
9、 responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hunga
10、ry, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre
11、: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10350-1:2008: E Licensed Copy: London South Bank University, South Bank University, 30/01/2009 13:48, Uncontrolled Copy, (c) BSI BS EN IS
12、O 10350-1:2008 EN ISO 10350-1:2008 (E) 3 Foreword The text of ISO 10350-1:2007 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 10350-1:2008 by Technical Committee CEN/TC 249 “Plastics” the sec
13、retariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2009, and conflicting national standards shall be withdrawn at the latest by February 2009. Attention is
14、drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 10350-1:2000. According to the CEN/CENELEC Internal Regulations, th
15、e national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, No
16、rway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 10350-1:2007 has been approved by CEN as a EN ISO 10350-1:2008 without any modification. Licensed Copy: London South Bank University, South Bank University, 30/0
17、1/2009 13:48, Uncontrolled Copy, (c) BSI BS EN ISO 10350-1:2008 ISO 10350-1:2007(E) ISO 2007 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 3 4 Specimen preparation and conditioning 3 5 Test requirements. 4 6 Presentati
18、on of results. 4 Licensed Copy: London South Bank University, South Bank University, 30/01/2009 13:48, Uncontrolled Copy, (c) BSI BS EN ISO 10350-1:2008 ISO 10350-1:2007(E) iv ISO 2007 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of
19、national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Inte
20、rnational organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with th
21、e rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval b
22、y at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10350-1 was prepared by Technical Committee
23、ISO/TC 61, Plastics, Subcommittee SC 2, Mechanical properties. This second edition cancels and replaces the first edition (ISO 10350-1:1998), which has been technically revised. ISO 10350 consists of the following parts, under the general title Plastics Acquisition and presentation of comparable sin
24、gle-point data: Part 1: Moulding materials Part 2: Long-fibre-reinforced plastics Licensed Copy: London South Bank University, South Bank University, 30/01/2009 13:48, Uncontrolled Copy, (c) BSI BS EN ISO 10350-1:2008 ISO 10350-1:2007(E) ISO 2007 All rights reserved v Introduction ISO 10350 has been
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN ISO 10350 2008
链接地址:https://www.31doc.com/p-3743948.html