《BS-EN-ISO-1302-2002.pdf》由会员分享,可在线阅读,更多相关《BS-EN-ISO-1302-2002.pdf(60页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation The European Standard EN ISO 1302:2002 has the status of a British Standard ICS 01.100.20; 17.040.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY
2、 COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 1302:2002 This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Policy and Strategy Committee, was published unde
3、r the authority of the Standards Policy and Strategy Committee on 16 May 2002 BSI 16 May 2002 ISBN 0 580 39629 0 National foreword This British Standard is the official English language version of EN ISO 1302:2002. It is identical with ISO 1302:2002. It supersedes BS ISO 1302:1992 which is withdrawn
4、. The UK participation in its preparation was entrusted by Technical Committee TDW/4, Technical, product specification Methodology, presentation and verification, to Subcommittee TDW/4/-/1, Technical product documentation Specification and presentation methodology, which has the responsibility to: A
5、 list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Inte
6、rnational Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a
7、 British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related internation
8、al and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii to v, a blank page, pages 1 to 46, the Annex ZA (2 pages), an inside back cover and
9、 a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME E
10、UROPENNE EUROPISCHE NORM EN ISO 1302 February 2002 ICS 01.100.20; 17.040.20 English version Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation (ISO 1302:2002) Spcification gomtrique des produits (GPS) - Indication des tats de surface dans la d
11、ocumentation technique de produits (ISO 1302:2002) Geometrische Produktspezifikation (GPS) - Angabe der Oberflchenbeschaffenheit in der technischen Produktdokumentation (ISO 1302:2002) This European Standard was approved by CEN on 17 January 2002. CEN members are bound to comply with the CEN/CENELEC
12、 Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN me
13、mber. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members
14、 are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALI
15、SATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2002 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1302:2002 E Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:13:08 GMT+00
16、:00 2006, Uncontrolled Copy, (c) BSI I NESO 31:2002( 20E) 2 CORRECTED 2002-04-10 Foreword This document (ISO 1302:2002) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification“ in collaboration with Technical Committee CEN/TC 290 “Dime
17、nsional and geometrical product specification and verification“, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2002, and conflicting national st
18、andards shall be withdrawn at the latest by August 2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Icel
19、and, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 1302:2002 has been approved by CEN as a European Standard without any modifications. NOTE Normative references to In
20、ternational Standards are listed in annex ZA (normative). EN ISO 1302:2002 Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Reference number ISO 1302:2002(E) OSI 2002 INTERNATIONAL STANDARD ISO 1302 Fourth edition 2002-02-01 Geometrical Produ
21、ct Specifications (GPS) Indication of surface texture in technical product documentation Spcification gomtrique des produits (GPS) Indication des tats de surface dans la documentation technique de produits EN ISO 1302:2002 Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:13:08 GMT+00:00 200
22、6, Uncontrolled Copy, (c) BSI ii EN ISO 1302:2002 Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI I SO 2002 All irthgs ersedevr iii Contents Page Foreword.iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Graphi
23、cal symbols for the indication of surface texture.3 5 Composition of complete graphical symbol for surface texture5 6 Indication of surface texture parameters6 7 Indication of manufacturing method or related information.11 8 Indication of the surface lay.12 9 Indication of machining allowance14 10 S
24、ummarizing of indications of surface texture requirements and their values14 11 Position on drawings and other technical product documentation.14 Annex A (normative) Proportions and dimensions of graphical symbols20 Annex B (informative) Synoptive tables .23 Annex C (informative) Examples of indicat
25、ion of surface texture requirements .26 Annex D (informative) Minimum indications for unambiguous control of surface functions.30 Annex E (informative) Surface texture parameter designations33 Annex F (informative) Evaluation length, ln36 Annex G (informative) Transmission band and sampling length.3
26、7 Annex H (informative) Consequences of new ISO surface texture standards .39 Annex I (informative) Former practice 41 Annex J (informative) Relation to the GPS matrix model .44 Bibliography46 EN ISO 1302:2002 Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:13:08 GMT+00:00 2006, Uncontroll
27、ed Copy, (c) BSI iv I SO 2002 All irthgs ersedevr Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each
28、 member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internationa
29、l Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards
30、 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be
31、the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 1302 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification. This fourth edition cancels and replaces
32、 the third edition (ISO 1302:1992), which has been technically revised. Annex A forms a normative part of this International Standard. Annexes B, C, D, E, F, G, H, I and J are for information only. EN ISO 1302:2002 Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:13:08 GMT+00:00 2006, Uncon
33、trolled Copy, (c) BSI I SO 2002 All irthgs ersedevr v Introduction This International Standard is a geometrical product specification (GPS) standard and is to be regarded as a general GPS standard (see ISO/TR 14638). It influences link 1 of the chain of standards on roughness, waviness and primary p
34、rofile. For more detailed information of the relation of this International Standard to other standards and the GPS matrix model, see annex J. This edition of ISO 1302 has been developed for use together with the new editions of the surface texture standards issued in 1996 and 1997, which introduce
35、many radical changes compared with the content of the former surface texture standards issued in the 1980s. The changes are so radical that the drawing indications in some instances have a completely new interpretation. Annex H gives detailed information on these changes. Drawing indications applied
36、 on technical drawings according to former editions of this International Standard refer to the rules given in the surface texture standards issued at the time of issue and can only be interpreted according to those surface texture standards. Annex I provides information on former practices. The dra
37、wing indications given in this edition are to be used for the unambiguous reference to the new surface texture standards issued in 1996 and 1997. Textual indications in this edition of ISO 1302 are under continuous development within ISO/TC 213 and a separate, detailed standard on this issue is unde
38、r preparation. Consequently, the textual indications given may change in future editions of ISO 1302. EN ISO 1302:2002 Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:13:08 GMT+00:00
39、2006, Uncontrolled Copy, (c) BSI INTENRATIONAL TSANDADR IS:2031 O2002(E) I SO 2002 All irthgs ersedevr 1 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation 1 Scope This International Standard specifies the rules for the indication of surface tex
40、ture in technical product documentation (e.g. drawings, specifications, contracts, reports) by means of graphical symbols and textual indications. It is applicable to the indication of requirements for surfaces by means of a) profile parameters, according to ISO 4287, related to the R-profile (rough
41、ness parameters), W-profile (waviness parameters), and P-profile (structural parameters), b) motif parameters, according to ISO 12085, related to the roughness motif, and waviness motif, c) parameters related to the material ratio curve according to ISO 13565-2 and ISO 13565-3. NOTE For the indicati
42、on of requirements for surface imperfections (pores, scratches etc.), which cannot be specified using surface texture parameters, reference is made to ISO 8785, which covers surface imperfections. 2 Normative references The following normative documents contain provisions which, through reference in
43、 this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the
44、 most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 129-1:1), Technical drawings Indication of dimensions
45、and tolerances Part 1: General principles ISO 1101:2), Geometrical Product Specifications (GPS) Geometrical tolerancing Tolerancing of form, orientation, location and run-out 1) To be published. (Revision of ISO 129:1985) 2) To be published. (Revision of ISO 1101:1983) EN ISO 1302:2002 1 Licensed Co
46、py: sheffieldun sheffieldun, na, Wed Nov 15 05:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI IS:2031 O2002(E) 2 I SO 2002 All irthgs ersedevr ISO 3098-2:2000, Technical product documentation Lettering Part 2: Latin alphabet, numerals and marks ISO 3274:1996, Geometrical Product Specifications (GP
47、S) Surface texture: Profile method Nominal characteristics of contact (stylus) instruments ISO 4287:1997, Geometrical product specifications (GPS) Surface texture: Profile method Terms, definitions and surface texture parameters ISO 4288:1996, Geometrical product specifications (GPS) Surface texture
48、: Profile method Rules and procedures for the assessment of surface texture ISO 8785:1998, Geometrical product specifications (GPS) Surface imperfections Terms, definitions and parameters ISO 10135:3), Technical drawings Simplified representation of moulded, cast and forged parts ISO 10209-1:1992, T
49、echnical product documentation Vocabulary Part 1: Terms relating to technical drawings: general and types of drawings ISO 11562:1996, Geometrical Product Specifications (GPS) Surface texture: Profile method Metrological characteristics of phase correct filters ISO 12085:1996, Geometrical product specifications (GPS) Surface texture: Profile method Motif parameters ISO 13565-1:1996, Geometrical Product Specifications (GPS) Surface texture: Profile method; Surfaces having stratified func
链接地址:https://www.31doc.com/p-3743994.html