BS-EN-ISO-1660-1996 BS-308-2.3-1995.pdf
《BS-EN-ISO-1660-1996 BS-308-2.3-1995.pdf》由会员分享,可在线阅读,更多相关《BS-EN-ISO-1660-1996 BS-308-2.3-1995.pdf(14页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 1660:1996 BS 308-2.3: 1996 Technical drawings Dimensioning and tolerancing of profiles The European Standard EN ISO 1660:1995 has the status of a British Standard ICS 01.100.10 Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 14 06:18:29 GMT+00:00 2006, Uncontrolled Cop
2、y, (c) BSI BS EN ISO 1660:1996 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 February 1996 BSI 12-1998 The following BSI references relate to the work on this stand
3、ard: Committee reference TDE/4 Draft announced in BSI News November 1995 ISBN 0 580 25259 0 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee TDE/4, Engineering drawing practice, upon which the following bodies were represe
4、nted: Atomic Weapons Establishment British Gas plc British Standards Society Drawing Office Material Manufacturers and Dealers Association Electricity Association Gauge and Tools Makers Association HEVAC Association Institution of Chemical Engineers Institution of Engineering Designers Power Generat
5、ion Contractors Association Society of British Aerospace Companies Ltd. University of Warwick Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 14 06:18:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 1660:1996 BSI 12-1998i Contents
6、Page Committees responsibleInside front cover National forewordii Foreword2 1Scope and field of application3 2Reference3 3Dimensioning3 4Indication of tolerances3 Bibliography7 Figure 13 Figure 23 Figure 34 Figure 44 Figure 55 Figure 66 List of referencesInside back cover Licensed Copy: sheffieldun
7、sheffieldun, na, Tue Nov 14 06:18:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 1660:1995 ii BSI 12-1998 National foreword This British Standard has been prepared by Technical Committee TDE/4 and is the English language version of EN ISO 1660:1995 Technical drawings Dimensioning and tolera
8、ncing of profiles, published by the European Committee for Standardization (CEN). It is identical with ISO 1660:1987 published by the International Organization for Standardization (ISO). This British Standard partially supersedes BS 308-2. It is envisaged that when the full range of European Standa
9、rds on technical drawing is implemented BS 308 will be withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity
10、 from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be i
11、ndicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 14 06:18:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1660 September 1995 ICS 01.100.10 Descriptors: Drawings, technical drawings,
12、dimensioning, profiles, designation English version Technical drawings Dimensioning and tolerancing of profiles (ISO 1660:1987) Dessins techniques Cotation et tolrancement des profils (ISO 1660:1987) Technische Zeichnungen Maangaben und Toleranzeintragungen von Profilen (ISO 1660:1987) This European
13、 Standard was approved by CEN on 1995-05-06. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning
14、 such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own langu
15、age and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and U
16、nited Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1995 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its mem
17、bers. Ref. No. EN ISO 1660:1995 E Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 14 06:18:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 1660:1995 BSI 12-1998 2 Foreword The text of the International Standard from ISO/TC 10, “Technical drawings, product definition and verification”, of th
18、e International Organization for Standardization (ISO) has been taken over as a European Standard by the Technical Committee CEN/TC 290, “Dimensional and geometrical product definition and related documentation”. This European Standard shall be given the status of a national standard, either by publ
19、ication of an identical text or by endorsement, at the latest by March 1996, and conflicting national standards shall be withdrawn at the latest by March 1996. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium,
20、Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Tue Nov 14 06:18:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 1660:1995 BSI 12-19983 1 Scope
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-EN-ISO-1660-1996 BS-308-2.3-1995 BS EN ISO 1660 1996 308 2.3 1995
链接地址:https://www.31doc.com/p-3744036.html