《BS-ISO-TR-10194-1989.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-TR-10194-1989.pdf(18页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO TR 10194:1989 Implementation of ISO TR 10194:1989 Non-round general use light gauge metal containers Nominal filling volumes and nominal cross-sections UDC 621.798.144-034 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) B
2、SI BS ISO TR 10194:1989 This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Board, was published under the authority of the Standards Board and comes into effect on 15 January 1996 BSI 01-2000 The following BSI references relate to the work on
3、 this standard: Committee reference PKW/2 Draft announced in BSI News June 1995 ISBN 0 580 25306 6 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PKW/2, Primary packaging, upon which the following bodies were represented
4、: Association of the British Pharmaceutical Industry British Aerosol Manufacturers Association British Fibreboard Packaging Association British Glass Manufacturers Confederation British Plastics Federation British Retail Consortium Chemical Industries Association Cosmetic, Toiletry and Perfumery Ass
5、ociation Limited Department of Trade and Industry (Consumer Safety Unit, CA Division) Department of Trade and Industry (Laboratory of the Government Chemist) Environmental and Technical Association for the Paper Sack Industry Flexible Packaging Association Institute of Packaging Institute of Trading
6、 Standards Administration Institute of Wastes Management Metal Packaging Manufacturers Association Packaging and Industrial Films Association Paper Federation of Great Britain Pira International The following bodies were also represented in the drafting of the standard, through subcommittees and pan
7、els: British Coatings Federation Ltd. British Compressed Gases Association Consumer Policy Committee of BSI Engineering Equipment and Materials Users Association Health and Safety Executive LP Gas Association Society of Cosmetic Scientists Amendments issued since publication Amd. No.DateComments Lic
8、ensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO TR 10194:1989 BSI 01-2000i Contents Page Committees responsibleInside front cover National forewordii Forewordiii Text of ISO TR 101941 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 2
9、6 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO TR 10194:1989 ii BSI 01-2000 National foreword This British Standard reproduces verbatim ISO TR 10194:1989 and implements it as the UK national standard. This British Standard is published under the direction of the Consumer Products and S
10、ervices Sector Board whose Technical Committee PKW/2 has the responsibility to: aid enquirers to understand the text; present to the responsible international committee any enquiries on interpretation, or proposals for change, and keep UK interests informed; monitor related international and Europea
11、n developments and promulgate them in the UK. NOTEInternational and European Standards, as well as overseas standards, are available from Customer Services, BSI, 389 Chiswick High Road, London W4 4AL. A British Standard does not purport to include all the necessary provisions of a contract. Users of
12、 British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the ISO TR title page, pages ii to iv, pages
13、1 to 8 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI L
14、icensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10194:1989 (E) ii BSI 01-2000 Contents Page Forewordiii Introduction1 1Scope1 2Reference1 3Designation of containers (types and construction)1 4Characteristics1 5Current list of nominal f
15、illing volumes and nominal cross-sections1 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10194:1989 (E) BSI 01-2000iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards
16、 bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organiza
17、tions, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The main task of ISO technical committees is to prepare International Stand
18、ards. In exceptional circumstances a technical committee may propose the publication of a technical report of one of the following types: type 1, when the necessary support within the technical committee cannot be obtained for the publication of an International Standard, despite repeated efforts; t
19、ype 2, when the subject is still under technical development requiring wider exposure; type 3, when a technical committee has collected data of a different kind from that which is normally published as an International Standard (“state of the art”, for example). Technical reports are accepted for pu
20、blication directly by ISO Council. Technical reports of types 1 and 2 are subject to review within three years of publication, to decide whether they can be transformed into International Standards. Technical reports of type 3 do not necessarily have to be reviewed until the data they provide are co
21、nsidered to be no longer valid or useful. ISO/TR 10194, which is a technical report of type 3, was prepared by Technical Committee ISO/TC 52, Light gauge metal containers. Data of a similar nature to those presented in this Technical Report, but for round containers, are given in ISO/TR 10193:1989,
22、Round general use light gauge metal containers Nominal filling volumes and nominal diameters. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv blank Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontroll
23、ed Copy, (c) BSI ISO/TR 10194:1989 (E) BSI 01-20001 Introduction This Technical Report presents the results of a survey on the sizes of different types of non-round general use light gauge metal containers in current use. The way in which these data can be reduced sufficiently to establish an Intern
24、ational Standard is under consideration. 1 Scope This Technical Report gives a current list of nominal filling volumes and related nominal cross-sections for non-round general use light gauge metal containers. 2 Reference ISO 90-2:1986, Light gauge metal containers Definitions and determination meth
25、ods for dimensions and capacities Part 2: General use containers. 3 Designation of containers (types and construction) The definitions, and the designations of special features of these types of containers (necked-in and/or step-sided), are given in ISO 90-2. This Technical Report concerns the follo
26、wing container: full friction can, cylindrical; full friction can, tapered; friction closure can, cylindrical; friction closure can, tapered; flat top can, cylindrical; flat top can, tapered. 4 Characteristics 4.1 Nominal cross-sections: tolerances Tolerances on the cross-sections at the top end and
27、 at the bottom end are the following: dimension u 155 mm: 2 mm dimension 155 mm: 3 mm 4.2 Head spaces and nominal filling volumes: special case of the transport of dangerous goods With regard to head spaces required for the transport of dangerous goods, reference has to be made to valid regulations.
28、 5 Current list of nominal filling volumes and nominal cross-sections For each type of container mentioned in clause 3, the following are given: a figure showing the type of container; a table giving values of nominal filling volumes and of nominal cross-sections. NOTECross-sections that are underli
29、ned are preferred. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10194:1989 (E) 2 BSI 01-2000 5.1 Full friction can, cylindrical 5.2 Full friction can, tapered Nominal filling volume Cross-sections mm mm ml A1 X B1A2 X B2A1 X B1A2 X
30、 B2A1 X B1A2 X B2 10067 X 42 15067 X 42 25067 X 42 75099 X 67 3 000178 X 111 5 000244 X 135 8 200232 X 157 10 000232 X 157 Nominal filling volume Cross-sections mm mm ml A1 X B1A2 X B2A1 X B1A2 X B2A1 X B1A2 X B2 2 500251 X 161240 X 150 3 000300 X 145290 X 135 4 000251 X 161240 X 150 5 000 300 X 145
31、290 X 135 280 X 170270 X 160 10 000310 X 235300 X 225 12 000310 X 235298 X 222 15 000350 X 270335 X 255 16 000350 X 270335 X 255 18 000350 X 270335 X 255 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10194:1989 (E) BSI 01-20003 5.3
32、Friction closure can, cylindrical Nominal filling volume Cross-sections mm mm ml A1 X B1A2 X B2A1 X B1A2 X B2A1 X B1A2 X B2 12567 X 67 250 67 X 67 75 X 75 37575 X 75 500 89 X 89 106 X 68 112 X 112 750 89 X 89 112 X 67 1 000 95 X 95 100 X 100 106 X 68 120 X 65 1 500 112 X 112 127 X 127 1 70098 X 98 2
33、 500 98 X 98 153 X 153 165 X 93 2 60098 X 98 2 80098 X 98 3 750148 X 148 4 000148 X 148 4 500148 X 148 4 600104 X 167 5 000 148 X 148 153 X 153 180 X 110 180 X 120 185 X 185 5 500 148 X 148 98 X 98 5 520104 X 167 6 000148 X 148 6 700115 X 115 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15
34、:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10194:1989 (E) 4 BSI 01-2000 5.4 Friction closure can, tapered 5.5 Flat top can, cylindrical Nominal filling volume Cross-sections mm mm mlA1 X B1A2 X B2A1 X B1A2 X B2A1 X B1A2 X B2 8 800104 X 167 10 000 210 X 140 234 X 234 15 000 234 X 234 24
35、0 X 240 20 000 234 X 234 240 X 240 45 000310 X 310 Nominal filling volume Cross-sections mm mm ml A1 X B1A2 X B2A1 X B1A2 X B2A1 X B1A2 X B2 5 000159 X 120164 X 125 20 000240 X 240246 X 246 25 000240 X 240246 X 246 Nominal filling volume Cross-sections mm mm ml A1 X B1A2 X B2A1 X B1A2 X B2A1 X B1A2
36、X B2 10053 X 28 125 54 X 2668 X 28 53 X 28 55 X 33 250 70 X 3568 X 28 88 X 35 75 X 54 76 X 55 300 70 X 35 88 X 35 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10194:1989 (E) BSI 01-20005 Nominal filling volume Cross-sections mm mm
37、ml A1 X B1A2 X B2A1 X B1A2 X B2A1 X B1A2 X B2 500 75 X 54 82 X 54114 X 35 90 X 73 96 X 42 100 X 60 106 X 76 750 90 X 73 106 X 76 78094 X 68 1 000 65 X 106 90 X 73 95 X 62 99 X 67 106 X 76 110 X 62 114 X 58 135 X 50 120 X 65 1 200114 X 58 115 X 93 136 X 102 149 X 112 155 X 80 157 X 107 2 000166 X 63
38、166 X 103 168 X 73 175 X 59 176 X 64 195 X 110 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10194:1989 (E) 6 BSI 01-2000 Nominal filling volume Cross-sections mm mm ml A1 X B1A2 X B2A1 X B1A2 X B2A1 X B1A2 X B2 2 500 127 X 127 136
39、X 102 137 X 81 149 X 112 160 X 115 165 X 93 166 X 63 166 X 103 175 X 109 179 X 71 195 X 110 3 000 139 X 113 149 X 112 166 X 103 195 X 110 210 X 80 3 750166 X 103 3 785 139 X 113 166 X 103 4 000 139 X 113 148 X 148 149 X 112 166 X 103 157 X 107 175 X 109 176 X 119 195 X 110 4 500148 X 148 Licensed Co
40、py: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10194:1989 (E) BSI 01-20007 Nominal filling volume Cross-sections mm mm ml A1 X B1A2 X B2A1 X B1A2 X B2A1 X B1A2 X B2 5 000 139 X 113 148 X 148 149 X 112 150 X 115 153 X 153 159 X 120 160 X 115 164
41、 X 125 166 X 103 166 X 134 175 X 109 175 X 124 176 X 119 180 X 120 195 X 110 229 X 96 232 X 157 5 500148 X 148 6 000 148 X 148 175 X 108 8 000235 X 149 10 000 210 X 140 217 X 140 220 X 270 232 X 157 233 X 145 235 X 149 240 X 140 11 000235 X 149 12 000235 X 149 15 000234 X 234 17 600240 X 240 18 0002
42、34 X 234 18 800240 X 240 20 000 234 X 234 240 X 240 22 200240 X 240 25 000240 X 240 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10194:1989 (E) 8 BSI 01-2000 5.6 Flat top can, tapered Nominal filling volume Cross-sections mm mm ml
43、A1 X B1A2 X B2A1 X B1A2 X B2A1 X B1A2 X B2 2 000159 X 120164 X 125 2 500159 X 120164 X 125 3 000159 X 120164 X 125 5 000159 X 120164 X 125 10 000226 X 146231 X 151 15 000234 X 234231 X 231 18 000234 X 234231 X 231 20 000 234 X 234231 X 231 251 X 225257 X 231 240 X 240246 X 246 25 000 234 X 234231 X
44、231 240 X 240246 X 246 251 X 225257 X 231 286 X 252292 X 258 30 000286 X 252292 X 258 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:39 GMT+00:00 2006, Uncontrolled Copy, (c
45、) BSI BS ISO TR 10194:1989 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.
46、Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy o
47、r ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subs
48、cribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy
49、to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of
链接地址:https://www.31doc.com/p-3744633.html