《BS-EN-ISO-13906-2008.pdf》由会员分享,可在线阅读,更多相关《BS-EN-ISO-13906-2008.pdf(24页珍藏版)》请在三一文库上搜索。
1、BS EN ISO 13906:2008 ICS 65.120 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Animal feeding stuffs Determination of acid detergent fibre (ADF) and acid detergent lignin (ADL) contents (ISO 13906:2008) Incorporating Corrigendum March 2009 Licensed CopyChines
2、e University of Hong Kong, 11/04/2009 08:21, Uncontrolled Copy, (c) BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 3 ember 2008 BSI 2009 ISBN 978 0 580 Amendments/corrigenda issued since publication DateComments BS EN ISO 13906:2008 Nati
3、onal foreword This British Standard is the UK implementation of EN ISO 13906:2008 The UK participation in its preparation was entrusted to Technical Committee AW/10, Animal feeding stuffs. A list of organizations represented on this committee can be obtained on request to its secretary. This publica
4、tion does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. 1 Dec 67112 8 31 March 2009 Replacement to ISO text Licensed CopyChinese University of Hon
5、g Kong, 11/04/2009 08:21, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 13906 July 2008 ICS 65.120 English Version Animal feeding stuffs - Determination of acid detergent fibre (ADF) and acid detergent lignin (ADL) contents (ISO 13906:2008) Aliments des animaux
6、- Dtermination des teneurs en fibres au dtergent acide (ADF) et en lignine sulfurique (ADL) (ISO 13906:2008) Futtermittel - Bestimmung des Gehalts an Sure- Detergens-Faser (ADF) und Sure-Detergens-Lignin (ADL) (ISO 13906:2008) This European Standard was approved by CEN on 11 July 2008. CEN members a
7、re bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to
8、 the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the sa
9、me status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
10、Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means rese
11、rved worldwide for CEN national Members. Ref. No. EN ISO 13906:2008: E Licensed CopyChinese University of Hong Kong, 11/04/2009 08:21, Uncontrolled Copy, (c) BSI EN ISO 13906:2008 (E) 3 Foreword This document (EN ISO 13906:2008) has been prepared by Technical Committee ISO/TC 34 “Agricultural food p
12、roducts“ in collaboration with Technical Committee CEN/TC 327 “Animal feeding stuffs - Methods of sampling and analysis” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at
13、the latest by January 2009, and conflicting national standards shall be withdrawn at the latest by January 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any
14、or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary
15、, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 13906:2008 has been approved by CEN as a EN ISO 13906:2008 without any modificati
16、on. BS EN ISO 13906:2008 Licensed CopyChinese University of Hong Kong, 11/04/2009 08:21, Uncontrolled Copy, (c) BSI ISO 13906:2008(E) ISO 2008 All rights reserved iii Contents Page Foreword iv 1 Scope 1 2 Normative references1 3 Terms and definitions .1 4 Principle2 5 Reagents.2 6 Apparatus .3 7 Sam
17、pling.4 8 Preparation of test sample4 9 Procedure .4 10 Calculation and expression of results.6 11 Precision.7 12 Test report9 Annex A (informative) Results of interlaboratory test.10 Annex B (informative) Results of interlaboratory test.14 Bibliography17 BS EN ISO 13906:2008 Licensed CopyChinese Un
18、iversity of Hong Kong, 11/04/2009 08:21, Uncontrolled Copy, (c) BSI ISO 13906:2008(E) iv ISO 2008 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Stan
19、dards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also t
20、ake part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees
21、is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibil
22、ity that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13906 was prepared by Technical Committee ISO/TC 34, Food products, Subcommittee SC 10, Animal feeding stuffs. BS EN ISO 13906:2008
23、 Licensed CopyChinese University of Hong Kong, 11/04/2009 08:21, Uncontrolled Copy, (c) BSI INTERNATIONAL STANDARD ISO 13906:2008(E) ISO 2008 All rights reserved 1 Animal feeding stuffs Determination of acid detergent fibre (ADF) and acid detergent lignin (ADL) contents WARNING The use of this Inter
24、national Standard may involve hazardous materials, operations and equipment. This International Standard does not purport to address any safety risks associated with its use. It is the responsibility of the user of this International Standard to establish appropriate safety and health practices and
25、determine the applicability of local regulatory limitations prior to use. 1 Scope This International Standard specifies a method for the determination of acid detergent fibre (ADF) insoluble residue and acid detergent lignin (ADL) in all types of animal feeding stuffs. The limit of determination is
26、1 % mass fraction for ADF and 1,5 % mass fraction for ADL. A gravimetric routine and reference method is used. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated reference
27、s, the latest edition of the referenced document (including any amendments) applies. ISO 6498, Animal feeding stuffs Preparation of test samples 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 acid detergent fibre content ADF content mass fra
28、ction of fibrous residue obtained after treatment with cationic detergent in 0,5 mol/l sulfuric acid, primarily consisting of cellulose, lignin and insoluble protein complexes NOTE The ADF mass fraction is expressed as a percentage. 3.2 acid detergent lignin content ADL content mass fraction of resi
29、due remaining after cellulose and other organic matter is solubilized by 72 % mass fraction (12,00 mol/l) sulfuric acid NOTE The ADL mass fraction is expressed as a percentage. BS EN ISO 13906:2008 Licensed CopyChinese University of Hong Kong, 11/04/2009 08:21, Uncontrolled Copy, (c) BSI ISO 13906:2
30、008(E) 2 ISO 2008 All rights reserved 4 Principle ADF is determined in the first stage of the method. Cationic detergent solution is used to remove acid-labile carbohydrates, protein that is not complexed into Maillard products (heat damaged), and fats. The remaining fibrous residue is primarily cel
31、lulose and lignin (plant products) or insoluble protein complexes (animal products and heat-damaged feeds). The residue is weighed for the determination of ADF. In the second stage, the remaining residue is solubilized by 72 % mass fraction (12,00 mol/l) sulfuric acid, leaving the lignin (ADL) which
32、 is determined gravimetrically. 5 Reagents Use only reagents of recognized analytical grade, unless otherwise specified, and only distilled or deionized water or water of at least equivalent purity. 5.1 Acid detergent solution. Add 20 g cetyl(trimethyl)ammonium bromide (technical grade) to 1 l of 0,
33、5 mol/l sulfuric acid, previously standardized. Agitate to aid dissolution. 5.2 Sulfuric acid, 72 % mass fraction (12,00 mol/l). Standardize sulfuric acid (H2SO4) to a relative density of 1,634 at 20 C or 12,00 mol/l as follows. Calculate the mass, in grams, of acid, m(H2SO4), and the mass, in grams
34、, of water, m(H2O), needed to prepare 1 000 ml of solution using Equations (1) and (2): 24 24 10098,08 12 (H SO ) (H SO ) m w = (1) where w(H2SO4) is the assay mass fraction of sulfuric acid, expressed as a percentage. () 224 (H O)1000 1,634(H SO )mm= (2) where 1,634 is the relative density of 72 %
35、mass fraction sulfuric acid. Weigh water into a 1 000 ml volumetric flask and add the calculated amount of sulfuric acid slowly with occasional swirling. Cool the flask in a water bath while adding the required mass of acid. Cool to 20 C and verify the volume. The meniscus should be within 0,5 cm of
36、 the calibration mark at 20 C. If volume is too large, remove 5 ml water and add 4,55 ml sulfuric acid. If volume is too small, remove 1,5 ml and add 2,5 ml water. Repeat if necessary. 5.3 Filtration aid, diatomaceous earth1). 5.4 Acetone, technical grade. 5.5 n-Octanol, antifoaming agent. 1) Celite
37、, acid washed, and Celite 545 AW are examples of suitable products available commercially. This information is given for the convenience of users of this International Standard, and does not constitute an endorsement of these products by ISO. Alternative products may be used if they can be demonstra
38、ted to give comparable results. BS EN ISO 13906:2008 Licensed CopyChinese University of Hong Kong, 11/04/2009 08:21, Uncontrolled Copy, (c) BSI ISO 13906:2008(E) ISO 2008 All rights reserved 3 6 Apparatus Usual laboratory apparatus and, in particular, the following. 6.1 Analytical balance. 6.1.1 Ana
39、lytical balance, capable of weighing to the nearest 1 mg, with readability to 0,1 mg. 6.1.2 Analytical balance, with a measuring range up to 2 500 g, with readability to 1 g, for weighing sulfuric acid (5.2). 6.2 Mill, a cyclone mill or cutter mill or rotary mill or equivalent, giving a mean particl
40、e size of 0,22 mm to 0,26 mm. 6.3 Drying oven. 6.3.1 Air-ventilated oven, capable of operating at 103 C 2 C or 130 C 2 C. 6.3.2 Air-ventilated oven, capable of being maintained at 60 C 2 C. To speed up the drying of moist samples without creating artefact fibres, a vacuum oven, maintained at 60 C 2
41、C may also be used. 6.4 Refluxing apparatus, with individual heating units and cold water condensers. Any conventional apparatus suitable for crude fibre or amylase-treated neutral detergent fibre (aNDF) determinations is acceptable. Calibrate heating unit settings so that 50 ml of water boils in 4
42、min to 5 min when using cold water condensers. A Fibertec2)-type apparatus can be used and should boil 50 ml of water within 10 min. NOTE This setting can be expected to result in significant particle movement during refluxing. 6.5 Fritted-disk crucibles. Coarse porosity (pore size 40 m to 60 m) cru
43、cibles, 40 ml to 50 ml capacity, or Fibertec P22) (pore size 40 m to 100 m, 26 ml to 28 ml capacity). Clean new crucibles and ash at 525 C 15 C for 1 h. Clean crucibles after each use by ashing at 525 C 15 C for 3 h, removing ash by inverting in a detergent solution and sonicating for 7 min to 10 mi
44、n. Rinse crucibles in hot water, and soak in water at room temperature for at least 30 min. Occasionally test filtration rate as follows. Fill each crucible with 50 ml of distilled water (25 ml for Fibertec P22) crucibles) and record the time required to drain completely without vacuum should be 180
45、 s 60 s for Gooch2) or 75 s 30 s for P2. If drain time is 240 s (or 105 s for P2), clean crucible with acid or alkaline cleaning solution (Reference 4). If cleaning does not improve filtration rate, discard crucible. 6.6 Vacuum filter manifold. Suitable apparatus e.g. Fibertec2)-type cold extraction
46、 unit that allows adequate soaking of fibrous residues. 6.7 Incineration furnace, 525 C 15 C. 6.8 Reflux beakers. As an alternative to a reflux apparatus (6.4), 600 ml Berzelius beakers with condensers, e.g. made from 500 ml round-bottom flasks, may be used. 2) Example of a suitable product availabl
47、e commercially. This information is given for the convenience of users of this International Standard, and does not constitute an endorsement of this product by ISO. BS EN ISO 13906:2008 Licensed CopyChinese University of Hong Kong, 11/04/2009 08:21, Uncontrolled Copy, (c) BSI ISO 13906:2008(E) 4 IS
48、O 2008 All rights reserved 7 Sampling A representative sample should have been sent to the laboratory. It should not have been damaged or changed during transport or storage. Sampling is not a part of the method specified in this International Standard. A recommended sampling method is given in ISO
49、6497. 8 Preparation of test sample Prepare the test sample in accordance with ISO 6498. Reduce laboratory sample to approximately 100 g (dry weight equivalent) and place half in a moisture-tight, sealed container for total moisture determination. Dry remaining wet ( 15 % mass fraction moisture) materials to 10 % mass fraction fat, and is recommended for test samples containing 5 % mass fraction fat. Weigh test samples into previously tared, oven-dried crucibles, place crucible on filtering ma
链接地址:https://www.31doc.com/p-3744730.html