BS-EN-ISO-10360-1-2001.pdf
《BS-EN-ISO-10360-1-2001.pdf》由会员分享,可在线阅读,更多相关《BS-EN-ISO-10360-1-2001.pdf(58页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 10360-1:2001 Geometrical Product Specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 1: Vocabulary The European Standard EN ISO 10360-1:2000 has the status of a British Standard ICS 17.040.30; 01.040.17 NO COPYING WITHOUT B
2、SI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN ISO 10360-1:2001 This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 October 2001 BSI
3、08-2001 ISBN 0 580 38408 x National foreword This British Standard is the official English language version of EN ISO 10360-1:2000. It is identical with ISO 10360-1:2000 The UK participation in its preparation was entrusted by Technical Committee TDW/4, Engineering drawing, metrology, precision meas
4、urement and all related documentation, to Subcommittee TDW/4/-/4, Engineers precision measuring equipment, including limits and fits, which has the responsibility to: A list of organizations represented on this Subcommittee can be obtained on request to its secretary. Cross-references The British St
5、andards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Stan
6、dard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the re
7、sponsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front
8、cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii to viii, pages 1 to 44, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments
9、 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10360-1 November 2000 ICS 17.040.30 English version Geometrical Product Specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 1: Vocabulary (ISO 10360-1:2000) Spcification gomtrique des prod
10、uits (GPS) - Essais de rception et de vrification priodique des machines mesurer tridimensionnelles (MMT) - Partie 1: Vocabulaire (ISO 10360-1:2000) Geometrische Produktspezifikation (GPS) - Annahmeprfung und Besttigungsprfung fr Koordinatenmessgerte (KMG) - Teil 1: Begriffe (ISO 10360-1:2000) This
11、European Standard was approved by CEN on 15 November 2000. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical referen
12、ces concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into i
13、ts own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain,
14、 Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2000 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Mem
15、bers. Ref. No. EN ISO 10360-1:2000 E Foreword The text of the International Standard ISO 10360-1:2000 has been prepared by Technical Committee ISO/TC 213 “ Dimensional and geometrical product specifications and verification “ in collaboration with Technical Committee CEN/TC 290 “ Dimensional and geo
16、metrical product specification and verification“, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2001, and conflicting national standards shall be w
17、ithdrawn at the latest by May 2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
18、Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 10360-1:2000 was approved by CEN as a European Standard without any modification. EN ISO 103601:2001 Reference number Numro de rfrence ISO 10360
19、-1:2000(E/F) ISO 2000 INTERNATIONAL STANDARD NORME INTERNATIONALE ISO 10360-1 First edition Premire dition 2000-11-15 Geometrical Product Specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 1: Vocabulary Spcification gomtrique des produits (GPS) Essa
20、is de rception et de vrification priodique des machines mesurer tridimensionnelles (MMT) Partie 1: Vocabulaire EN ISO 103601:2001 ii EN ISO 103601:2001 iii ContentsPage Forewordv Introduction.vii 1Scope 1 2General terms.1 3Terms relating to the probing system .8 4Terms relating to the stylus system
21、9 5Terms relating to the rotary table.13 6Terms relating to the operation of the CMM .13 7Terms relating to scanning.14 8Terms relating to artefacts15 9Terms relating to CMM error or error of indication15 10Terms relating to features.23 11Terms relating to software23 Annex A (informative) Descriptio
22、n of CMM types27 Annex B (informative) Relation to the GPS matrix model.38 Bibliography40 Index.41 EN ISO 103601:2001 iv SommairePage Avant-proposvi Introductionviii 1Domaine dapplication.1 2Termes gnraux .1 3Termes relatifs au systme de palpage.8 4Termes relatifs au systme de stylet.9 5Termes relat
23、ifs au plateau tournant.13 6Termes relatifs au fonctionnement de la MMT .13 7Termes relatifs au scanning .14 8Termes relatifs aux talons.15 9Termes relatifs lerreur dindication dune MMT ou lerreur dune MMT15 10Termes relatifs aux lments23 11Termes relatifs aux logiciels.23 Annexe A (informative) Des
24、cription des types de MMT27 Annexe B (informative) Relation avec la matrice GPS.38 Bibliographie.40 Index.43 EN ISO 103601:2001 v Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Intern
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN ISO 10360 2001
链接地址:https://www.31doc.com/p-3744865.html