BS-EN-ISO-17660-1-2006.pdf
《BS-EN-ISO-17660-1-2006.pdf》由会员分享,可在线阅读,更多相关《BS-EN-ISO-17660-1-2006.pdf(50页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 17660-1:2006 Welding Welding of reinforcing steel Part 1: Load-bearing welded joints ICS 25.160.10 ? December 2008 Incorporating Corrigendum Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:26, Uncontrolled Copy, (c) BSI BS EN ISO 17660-1:2
2、006 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2008 BSI 2008 ISBN 978 0 580 65546 3 National foreword This British Standard is the UK implementation of EN ISO 17660-1:2006. It is identical with ISO 17660-1:2006. Together with BS
3、 EN ISO 17760-2:2006 it One of the principal differences between BS 7123 and this standard is that BS 7123 offered more practical guidance on the welding process issues, some of these issues have been highlighted in the National Annex and further guidance can be found in parts 1 to 3 of BS EN 1011.
4、This standard is best used in conjunction with the National Annexes and the general good practices set out in the BS EN 1011 series. The UK participation in its preparation was entrusted to Technical Committee, WEE/43, Welding of steel for concrete reinforcement. A list of organizations represented
5、on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Comments supers
6、edes BS 7123:1989 which is withdrawn. Amendments/corrigenda issued since publication 31 December 2008 Date Correction to supersession details Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:26, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE
7、NORM EN ISO 17660-1 September 2006 ICS 25.160.10 English Version Welding - Welding of reinforcing steel - Part 1: Load-bearing welded joints (ISO 17660-1:2006) Soudage - Soudage des aciers darmatures - Partie 1: Assemblages transmettant des efforts (ISO 17660-1:2006) Schweien - Schweien von Betonsta
8、hl - Teil 1: Tragende Schweiverbindungen (ISO 17660-1:2006) This European Standard was approved by CEN on 2 August 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard withou
9、t any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language mad
10、e by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany,
11、 Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Man
12、agement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 17660-1:2006: E Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:26, Uncontrolled Copy, (c
13、) BSI Foreword This document (EN ISO 17660-1:2006) has been prepared by Technical Committee CEN/TC 121 “Welding“, the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 44 “Welding and allied processes“. This European Standard shall be given the status of a nationa
14、l standard, either by publication of an identical text or by endorsement, at the latest by March 2007, and conflicting national standards shall be withdrawn at the latest by March 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries
15、 are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Swi
16、tzerland and United Kingdom. ISO 17660-1:2006(E) BS EN ISO 17660-1:2006 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:26, Uncontrolled Copy, (c) BSI ISO 17660-1:2006(E) iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 1 3 Terms and
17、definitions. 2 4 Symbols and abbreviated terms . 3 5 Welding processes. 4 6 Load-bearing welded joints . 4 7 Materials 14 8 Quality requirements 14 9 Welding personnel 15 10 Welding procedure specification (WPS). 16 11 Welding procedures . 16 12 Production weld test. 18 13 Execution and inspection o
18、f production welding of reinforcing steel 19 14 Examination and testing of test specimens. 21 15 Production log. 24 Annex A (informative) Welding procedure specification (WPS) for welding processes 111, 114, 135 and 136 25 Annex B (informative) Technical knowledge of welding coordinator for welding
19、reinforcing steel . 27 Annex C (informative) Test specimens 28 Annex D (informative) Assessment of the manufacturer performing welding 32 Annex E (informative) Evaluation of testing of welded joints 33 Annex F (informative) Example for production log. 34 Annex G (informative) Classification of shear
20、 strength of load-bearing cross joints. 35 Annex H (informative) Examples of diameter combinations for welding cross joints using welding processes 21 and 23. 36 Bibliography. 37 BS EN ISO 17660-1:2006 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 04:26, Uncontrolled
21、 Copy, (c) BSI ISO 17660-1:2006(E) iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body
22、 interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotec
23、hnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by
24、the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent righ
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN ISO 17660 2006
链接地址:https://www.31doc.com/p-3745028.html