BS-EN-ISO-3506-3-1998.pdf
《BS-EN-ISO-3506-3-1998.pdf》由会员分享,可在线阅读,更多相关《BS-EN-ISO-3506-3-1998.pdf(20页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 3506-3:1998 Mechanical properties of corrosion-resistant stainless-steel fasteners Part 3: Set screws and similar fasteners not under tensile stress The European Standard EN ISO 3506-3:1997 has the status of a British Standard ICS 21.060.10 Licensed Copy: sheffieldun sheff
2、ieldun, na, Sat Nov 18 07:35:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 3506-3:1998 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 February 1998 BSI 05-
3、1999 ISBN 0 580 29087 5 National foreword This British Standard is the English language version of EN ISO 3506-3:1997. It is identical with ISO 3506-3:1997. The UK participation in its preparation was entrusted by Technical Committee FME/9, Bolts, nuts and accessories, to Subcommittee FME/9/1, Mecha
4、nical properties of fasteners, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and Europe
5、an developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to internatio
6、nal publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility o
7、f the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.
8、 Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN ISO title page, page 2, the ISO title page, page ii, pages 1 to 10, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporat
9、ed. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 18 07:35:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 3506-3:1998 BSI 05-1999i Contents Page National f
10、orewordInside front cover Foreword2 Forewordii Text of ISO 3506-31 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 18 07:35:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 18 07:35:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN S
11、TANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 3506-3 December 1997 ICS 21.060.10 Descriptors: See ISO document English version Mechanical properties of corrosion-resistant stainless-steel fasteners Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:1997) Caractristiques m
12、caniques des lments de fixation en acier inoxydable rsistant la corrosion Partie 3: Vis sans tte et lments de fixation similaires non soumis des contraintes de traction (ISO 3506-3:1997) Mechanische Eigenschaften von Verbindungselementen aus nichtrostenden Sthlen Teil 3: Gewindestifte und hnliche, n
13、icht auf Zug beanspruchte Schrauben (ISO 3506-3:1997) This European Standard was approved by CEN on 23 October 1997. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without an
14、y alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by
15、 translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ire
16、land, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation
17、 in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 3506-3:1997 E Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 18 07:35:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 3506-3:1997 BSI 05-1999 2 Foreword The text of the International Standard ISO 350
18、6-3:1997 has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Threaded and non-threaded mechanical fasteners and accessories”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standa
19、rd, either by publication of an identical text or by endorsement, at the latest by June 1998, and conflicting national standards shall be withdrawn at the latest by June 1998. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound
20、 to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 3506
21、-3:1997 was approved by CEN as a European Standard without any modification. NOTENormative references to International Standards are listed in Annex ZA (normative). Contents Page Foreword2 Introduction1 1Scope1 2Normative references1 3Designation, marking and finish2 4Chemical composition3 5Mechanic
22、al properties3 6Test methods4 Annex A (informative) Description of the groups and grades of stainless steels6 Annex B (informative) Austenitic stainless steel composition specifications8 Annex C (informative) Austenitic stainless steels for cold heading and extruding9 Annex D (informative) Time-temp
23、erature-diagram of intergranular corrosion in austenitic stainless steels, grade A2 (18/8 steels)10 Annex E (informative) Magnetic properties for austenitic stainless steels10 Annex F (informative) BibliographyInside back cover Annex ZA (normative) Normative references to international publications
24、with their relevant European publicationsInside back cover Figure 1 Designation system for stainless steel grades and property classes for set screws and similar fasteners2 Figure 2 Torque test equipment5 Figure D.110 Table 1 Designations of property classes in relation to Vickers hardness2 Table 2
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN ISO 3506 1998
链接地址:https://www.31doc.com/p-3745105.html