BS-ISO-11529-2-2005.pdf
《BS-ISO-11529-2-2005.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-11529-2-2005.pdf(18页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 11529-2:2005 Milling cutters Designation Part 2: Shank-type and bore-type milling cutters with indexable inserts ICS 25.100.20 ? BS ISO 11529-2:2005 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 10 June 2005 BSI 10 J
2、une 2005 ISBN 0 580 45942 X National foreword This British Standard reproduces verbatim ISO 11529-2:2005 and implements it as the UK national standard. It supersedes BS ISO 11529-2:1998 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools Tip
3、s And Inserts For Cutting Applications, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in t
4、he BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible
5、 for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK inte
6、rests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 10, an inside back cover and a back cover. The BSI copy
7、right notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Reference number ISO 11529-2:2005(E) INTERNATIONAL STANDARD ISO 11529-2 Second edition 2005-03-15 Milling cutters Designation Part 2: Shank-type and bore-typ
8、e milling cutters with indexable inserts Fraises Dsignation Partie 2: Fraises queue et fraises trou plaquettes amovibles BS ISO 11529-2:2005 ii BS ISO 11529-2:2005 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member
9、 bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental
10、 and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directiv
11、es, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies
12、casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11529-2 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee
13、SC 9, Tools with cutting edges made of hard cutting materials. This second edition cancels and replaces the first edition (ISO 11529-2:1998), which has been technically revised. In particular, it incorporates in 4.10.1 the addition of hollow taper shanks (HSK), types A and C. ISO 11529 consists of t
14、he following parts, under the general title Milling cutters Designation: ? Part 1: Shank-type end mills of solid or tipped design ? Part 2: Shank-type and bore-type milling cutters with indexable inserts BS ISO 11529-2:2005 blank BS ISO 11529-2:2005 1 Milling cutters Designation Part 2: Shank-type a
15、nd bore-type milling cutters with indexable inserts 1 Scope This part of ISO 11529 establishes a designation system for shank- and bore-type milling cutters embodying hard-material, indexable inserts, with the purpose of simplifying communication between the users and suppliers of such tools. 2 Norm
16、ative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3002-1:1982, Basic quantitie
17、s in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers ISO 3002-3:1984, Basic quantities in cutting and grinding Part 3: Geometric and kinematic quantities in cutting 3 Summary explanation of the designa
18、tion system Shank-type and bore-type milling cutters are designated by codes comprising symbols which identify the important features of the mills. Extensions to the designation codes to include manufacturers or suppliers information about the milling cutters is described in Clause 5. No addition to
19、 or extension of the designation system given in this part of ISO 11529 shall be made without consulting with Technical Committee ISO/TC 29 and obtaining its agreement. The symbols defined by this part of ISO 11529 are: Position Definition of designation symbols 1 Designation symbol (letter) identif
20、ying the design of milling cutter (see 4.1) 2 Designation symbol (letter) identifying the type of milling cutter (see 4.2) 3 Designation symbol (number) identifying the cutting-edge angle, ?r (see 4.3) 4 Designation symbol (letter) identifying the shape of insert (see 4.4) 5 Designation symbol (numb
21、er) identifying the diameter, ? (see 4.5) 6 Designation symbol (letter) identifying the hand of cutting (see 4.6) BS ISO 11529-2:2005 2 7 Designation symbol (number) identifying the maximum cutting depth or width, ap (see 4.7) 8 Designation symbol (letter) identifying the orientation of the pockets
22、for indexable inserts in milling cutters (see 4.8) 9 Designation symbol (number) identifying the number of effective cutting edges (see 4.9) 10 Designation symbol (letter) identifying the type of shank or bore (see 4.10) 11 Designation symbol (number) identifying the size of shank or bore (see 4.11)
23、 EXAMPLE 1 2 3 4 5 6 7 8 9 10 11 S A 75 S 100 R 010 A 08 S 32 4 Designation symbols 4.1 Designation symbol identifying design of milling cutter Position 1 Designation symbol Design CTop clamp PClamping, insert with hole SClamping with screw, insert with hole TTangentially mounted insert, with hole V
24、Tangentially mounted insert, without hole WWedge clamping, insert without hole XSpecial feature 4.2 Designation symbol identifying type of milling cutter Position 2 Designation symbol Type of milling cutter Shape A Face mill Square shoulder face mill ap? ? B Face mill Square shoulder face mill ap? ?
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS ISO 11529 2005
链接地址:https://www.31doc.com/p-3745391.html