BS-ISO-1361-1997.pdf
《BS-ISO-1361-1997.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-1361-1997.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 1361:1997 Light-gauge metal containers Round open-top cans Internal diameters ICS 55.120 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 01:52:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 1361:1997 This British Standard, having been prepared under the direction
2、 of the Consumer Products and Services Sector Board, was published under the authority of the Standards Board and comes into effect on 15 March 1998 BSI 04-1999 ISBN 0 580 29251 7 National foreword This British Standard reproduces verbatim ISO 1361:1998 and implements it as the UK national standard.
3、 It supersedes BS 5774:1984 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee PKW/2, Primary packaging, to Subcommittee PKW/2/2, Metal packaging, which has the responsibility to: aid enquirers to understand the text; present to the responsible internati
4、onal/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its
5、secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Stan
6、dards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pa
7、ges This document comprises a front cover, an inside front cover, pages i and ii, the ISO title page, page ii, page 1 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cove
8、r. Amendments issued since publication Amd. No.Datecomments Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 01:52:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 1361:1997 BSI 04-1999i Contents Page National forewordInside front cover Forewordii 1Scope1 2Normative references1 3Recommende
9、d diameters1 4Provisional additional diameters1 Table 11 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 01:52:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 01:52:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheff
10、ieldun sheffieldun, na, Mon Nov 27 01:52:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 1361:1997 ii BSI 04-1999 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Sta
11、ndards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also
12、take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Internation
13、al Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 1361 was prepared by Technical Committee ISO/TC 52, Light gauge metal containers, Subcommittee 4, Open-top containers. This fourth edition cancels and replaces the third edition (ISO 1361:1
14、983), in which the following technical changes have been made: nearly all dimensions and tolerances of the actual internal body diameters have been slightly changed to reflect the most current practice; nominal necked-in diameters are included which, associated with the internal body diameters, allo
15、w the stacking of three-piece cans; the following diameters, which were considered acceptable until the end of 1987, are deleted: 56; 57; 61; 70; 71; 72; 93; 100; 109; 113; 126; 135; 138; 154; a new list of diameters which are acceptable for a five-year period has been drawn up. Descriptors: Packagi
16、ng, metal packaging, food packaging, containers, cans, dimensions, diameters, dimensional tolerances. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 01:52:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 1361:1997 BSI 04-19991 1 Scope This International Standard establishes a list of rec
17、ommended diameters for round two-piece and three-piece cans in tinplate or aluminium seamed after filling and defined by their nominal gross lidded capacity. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this Interna
18、tional Standard. At the time of the publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated belo
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS ISO 1361 1997
链接地址:https://www.31doc.com/p-3745465.html