BS-ISO-13985-2006.pdf
《BS-ISO-13985-2006.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-13985-2006.pdf(26页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 13985:2006 Liquid hydrogen Land vehicle fuel tanks ICS 43.060.40 ? Licensed Copy: London South Bank University, London South Bank University, Wed Aug 08 04:02:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS ISO 13985:2006 This British Standard was published under the authori
2、ty of the Standards Policy and Strategy Committee on 31 July 2007 BSI 2007 ISBN 978 0 580 58836 5 National foreword This British Standard is the UK implementation of ISO 13985:2006. The UK participation in its preparation was entrusted to Technical Committee PVE/3, Gas containers. A list of organiza
3、tions represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligation
4、s. Amendments issued since publication Amd. No. DateComments Licensed Copy: London South Bank University, London South Bank University, Wed Aug 08 04:02:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI Reference number ISO 13985:2006(E) INTERNATIONAL STANDARD ISO 13985 First edition 2006-11-01 Liquid h
5、ydrogen Land vehicle fuel tanks Hydrogne liquide Rservoirs de carburant pour vhicules terrestres BS ISO 13985:2006 Licensed Copy: London South Bank University, London South Bank University, Wed Aug 08 04:02:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ii Licensed Copy: London South Bank University,
6、 London South Bank University, Wed Aug 08 04:02:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 2 4 Requirements 3 4.1 General requirements. 3 4.2 Mechanical stresses. 3 4.3 Thermal stresses 4 4
7、.4 Materials 5 4.5 Design 5 4.6 Insulation. 5 4.7 Accessories. 6 4.8 Manufacturing and assembly 7 5 Type tests 7 5.1 Approval of new designs . 7 5.2 Inner tank burst pressure test. 8 5.3 Thermal autonomy test 8 5.4 Maximum filling level test 8 5.5 Accessory type tests 8 6 Routine tests and inspectio
8、n. 8 6.1 General. 8 6.2 Pressure test . 8 6.3 Leak test 9 6.4 Verification of the dimensions 9 6.5 Destructive and non-destructive tests of welded joints. 9 6.6 Visual inspection 9 7 Marking and labelling. 9 7.1 Marking method 9 7.2 Inner tank markings 9 7.3 Outer jacket markings 10 7.4 Temporary ma
9、rkings for first filling 10 Annex A (normative) Fuel tank operating ranges. 11 Annex B (informative) Hydrogen compatibility. 12 Annex C (normative) Fuel tank type tests . 13 Annex D (normative) Accessory type tests. 15 BS ISO 13985:2006 Licensed Copy: London South Bank University, London South Bank
10、University, Wed Aug 08 04:02:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through IS
11、O technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates c
12、losely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. D
13、raft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this do
14、cument may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13985 was prepared by Technical Committee ISO/TC 197, Hydrogen technologies. BS ISO 13985:2006 Licensed Copy: London South Bank University, London South Bank University, W
15、ed Aug 08 04:02:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI v Introduction The fuel tanks described in this International Standard are intended to be used in conjunction with the fuelling system interface described in ISO 13984. BS ISO 13985:2006 Licensed Copy: London South Bank University, London
16、 South Bank University, Wed Aug 08 04:02:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI blank Licensed Copy: London South Bank University, London South Bank University, Wed Aug 08 04:02:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 1 Liquid hydrogen Land vehicle fuel tanks 1 Scope This International
17、Standard specifies the construction requirements for refillable fuel tanks for liquid hydrogen used in land vehicles as well as the testing methods required to ensure that a reasonable level of protection from loss of life and property resulting from fire and explosion is provided. This Internationa
18、l Standard is applicable to fuel tanks intended to be permanently attached to land vehicles. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edit
19、ion of the referenced document (including any amendments) applies. ISO 188:1998, Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance tests ISO 1431-1, Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing ISO 2768-1, General
20、 tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 6957, Copper alloys Ammonia test for stress corrosion resistance ISO 9227, Corrosion tests in artificial atmospheres Salt spray tests ISO 13984, Liquid hydrogen Land vehicle fuelling system
21、interface ISO 21010, Cryogenic vessels Gas/materials compatibility ISO 21013-3, Cryogenic vessels Pressure-relief accessories for cryogenic service Part 3: Sizing and capacity determination ISO 21014, Cryogenic vessels Cryogenic insulation performance ISO 21028-1, Cryogenic vessels Toughness require
22、ments for materials at cryogenic temperature Part 1: Temperatures below 80 C ISO 21029-1:2004, Cryogenic vessels Transportable vacuum insulated vessels of not more than 1 000 litres volume Part 1: Design, fabrication, inspection and tests ISO 23208, Cryogenic vessels Cleanliness for cryogenic servic
23、e BS ISO 13985:2006 Licensed Copy: London South Bank University, London South Bank University, Wed Aug 08 04:02:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 2 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 accessory device fixed directly to
24、 the inner tank or outer jacket of a fuel tank such as a pressure relief valve, shut-off valve, non-return valve or level gauge 3.2 boil-off management system system that controls the boil off of gas under normal conditions 3.3 burst pressure pressure that causes the rupture of a pressure vessel sub
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS ISO 13985 2006
链接地址:https://www.31doc.com/p-3745536.html