BS-EN-ISO-5456-3-1999.pdf
《BS-EN-ISO-5456-3-1999.pdf》由会员分享,可在线阅读,更多相关《BS-EN-ISO-5456-3-1999.pdf(22页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 5456-3:1999 Technical drawings Projection methods Part 3: Axonometric representations The European Standard EN ISO 5456-3:1999 has the status of a British Standard ICS 01.100.01 ? Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:12:59 GMT+00:00 2006, Uncontrolled
2、Copy, (c) BSI BS EN ISO 5456-3:1999 This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 October 1999 BSI 15 September 2002 ISBN 0 580 35177 7 National foreword Th
3、is British Standard is the English language version of EN ISO 5456-3:1999. It is identical with ISO 5456-3:1996. The UK participation in its preparation was entrusted to Technical Committee TDE/4, Engineering drawing, metrology, precision measurement and all related documentation, which has the resp
4、onsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresp
5、onding European publications. The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI St
6、andards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquire
7、rs to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This docume
8、nt comprises a front cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii to iv, pages 1 to 13 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication
9、 Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:12:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 5456-3 July 1999 ICS 01.100.10 English version Technical drawings Projection methods Part 3: Axonometric represent
10、ations (ISO 5456-3:1996) Dessins techniques Mthodes de projection Partie 3: Reprsentations axonomtriques (ISO 5456-3:1996) Technishce Zeichnungen Projektionsmethoden Teil 3: Axonometrische Darstellungen (ISO 5456-3:1996) This European Standard was approved by CEN on 27 May 1999. CEN members are boun
11、d to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Ce
12、ntral Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status a
13、s the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standar
14、dization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 5456-3:1999 E Licensed Copy: sheffieldun sheff
15、ieldun, na, Wed Nov 15 05:12:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 5456-3:1999 BSI 15 September 2002 Foreword The text of the International Standard from Technical Committee ISO/TC 10 “Technical drawings, product definition and related documentation” of the International Organization
16、for Standardization (ISO) has been taken over as a European Standard CEN/CS. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2000, and conflicting national standards shall be withdrawn at
17、the latest by January 2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembou
18、rg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 5456-3:1996 has been approved by CEN as a European Standard without any modification. NOTE Normative references to International Standards are listed in
19、 Annex ZA (normative). Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:12:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:12:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 5456-3:1999 ii BSI 15 September 2002 Foreword ISO (the I
20、nternational Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee
21、has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnica
22、l standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 5456-3 was prepared by Tech
23、nical Committee ISO/TC 10, Technical drawings, product definition and related documentation, Subcommittee SC 1, Basic conventions. ISO 5456 consists of the following parts, under the general title Technical drawings Projection methods: Part 1: Synopsis Part 2: Orthographic representations Part 3: Ax
24、onometric representations Part 4: Central projection Annex A of this part of ISO 5456 if for information only. Descriptors: graphic methods, drawings, technical drawings, graphic projections. Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 15 05:12:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI E
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN ISO 5456 1999
链接地址:https://www.31doc.com/p-3746342.html