BS-EN-ISO-8662-4-1995 ISO-8662-4-1994.pdf
《BS-EN-ISO-8662-4-1995 ISO-8662-4-1994.pdf》由会员分享,可在线阅读,更多相关《BS-EN-ISO-8662-4-1995 ISO-8662-4-1994.pdf(18页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 8662-4:1995 ISO 8662-4: 1994 Hand-held portable power tools Measurement of vibrations at the handle Part 4: Grinding machines The European Standard EN ISO 8662-4:1995 has the status of a British Standard Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 18 02:00:05 GMT+0
2、0:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 8662-4:1995 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 December 1995 BSI 08-1999 The following BSI references rel
3、ate to the work on this standard: Committee reference GME/21 Draft for comment 92/84671 DC ISBN 0 580 24873 9 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee GME/21, Mechanical vibration and shock, upon which the followin
4、g bodies were represented: Federation of Civil Engineering Contractors Imperial College of Science, Technology and Medicine Institute of Sound and Vibration Research Institution of Mechanical Engineers Lloyds Register of Shipping Ministry of Defence Open University Power Generation Contractors Assoc
5、iation (BEAMA Ltd.) Railway Industry Association of Great Britain Society of British Aerospace Companies Limited Society of Environmental Engineers The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Agricultural Engineers Association British
6、 Aggregate Construction Materials Industries British Agricultural and Garden Machinery Association Ltd. British Compressed Air Society British Gas plc British Hydraulic Tool Manufacturers Association British Occupational Hygiene Society British Railways Board Department of the Environment (Building
7、Research Establishment) Forestry Commission Health and Safety Executive Institute of Explosives Engineers Institute of Naval Medicine Institution of Electrical Engineers Medical Research Council Portable Electric Tool Manufacturers Association University College of Swansea University of Salford Amen
8、dments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 18 02:00:05 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 8662-4:1995 BSI 08-1999i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Introduction3 1Scope
9、3 2Normative references3 3Quantities to be measured3 4Instrumentation3 5Measurement direction and measurement location5 6Determination of working procedure6 7Measurement procedure and validity of measurements8 8Test report8 Annex A (informative) Model test report for vibrations at the handle of grin
10、ders10 Annex ZA (normative) Normative references to international publications with their relevant European publications12 Annex ZB (informative) Bibliography12 Figure 1 Measurement directions, examples of position of transducers and application of feed force4 Figure 2 Options for fastening of trans
11、ducers5 Figure 3 Grinder Working position of operator6 Figure 4 Specifications of test wheel and bushing7 Table 1 Dimensions of bushing8 Table 2 Dimensions of artificial test wheels for grinders other than straight grinders9 Table 3 Dimensions of artificial test wheels for straight grinders9 Table 4
12、 Feed force9 List of referencesInside back cover Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 18 02:00:05 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 8662-4:1995 ii BSI 08-1999 National foreword This British Standard has been prepared by Technical Committee GME/21, and is the English
13、 language version of EN ISO 8662-4:1995 Hand-held portable power tools Measurement of vibrations at the handle Part 4: Grinders published by the European Committee for Standardization (CEN). It is identical with ISO 8662-4:1994 published by the International Organization for Standardization (ISO). E
14、N 28662-4:1994 was produced as a result of international discussion in which the UK took an active part. Other Parts of ISO 8662 have been implemented in the BS EN 28662 series and the BS EN ISO 8662 series. A British Standard does not purport to include all the necessary provisions of a contract. U
15、sers of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference Publication referred toCorresponding British Standard EN 28662-1:1992 ISO 8662-1:1992 BS EN 28662-1:1993 Hand-held po
16、rtable power tools Measurement of vibrations at the handle Part 1: General Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN ISO title page, pages 2 to 12, an inside back cover and a back cover. This standard has been updated (see copyright date) a
17、nd may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 18 02:00:05 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8662-4 April 1995 ICS
18、13.060; 25.140.10 Descriptors: Tools, hand tools, power-operated tools, portable equipment, portable electronic machine tools, pneumatic equipment, grinding machines (tools), vibration, tests, vibration tests, tool handles English version Hand-held portable power tools Measurement of vibrations at t
19、he handle Part 4: Grinders (ISO 8662-4:1994) Machines moteur portatives Mesurage des vibrations au niveau des poignes Partie 4: Meuleuses (ISO 8662-4:1994) Handgehaltene motorbetriebene Maschinen Messung mechanischer Schwingungen am Handgriff Teil 4: Schleifmaschinen (ISO 8662-4:1994) This European
20、Standard was approved by CEN on 1995-02-15. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning
21、such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own langua
22、ge and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and Un
23、ited Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1995 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its memb
24、ers Ref. No. EN ISO 8662-4:1995 E Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 18 02:00:05 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 8662-4:1995 BSI 08-1999 2 Foreword The text of the International Standard ISO 8662-4:1994 has been prepared by Technical Committee ISO/TC 118, Compresso
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-EN-ISO-8662-4-1995 ISO-8662-4-1994 BS EN ISO 8662 1995 1994
链接地址:https://www.31doc.com/p-3746363.html