《BS-ISO-1924-3-2005.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-1924-3-2005.pdf(20页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 1924-3:2005 Paper and board Determination of tensile properties Part 3: Constant rate of elongation method (100 mm/min) ICS 85.060 ? Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:29:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 1924-3:2005 This British Stan
2、dard was published under the authority of the Standards Policy and Strategy Committee on 3 October 2005 BSI 3 October 2005 ISBN 0 580 46553 5 National foreword This British Standard reproduces verbatim ISO 1924-3:2005 and implements it as the UK national standard. The UK participation in its prepara
3、tion was entrusted to Technical Committee PAI/11, Methods of test for paper, board and pulps, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK i
4、nterests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to i
5、n this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of
6、a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to v, a blank page, pages 1 to 10,
7、an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:29:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI
8、 Reference number ISO 1924-3:2005(E) INTERNATIONAL STANDARD ISO 1924-3 First edition 2005-07-01 Paper and board Determination of tensile properties Part 3: Constant rate of elongation method (100 mm/min) Papier et carton Dtermination des proprits de traction Partie 3: Mthode gradient dallongement co
9、nstant (100 mm/min) BS ISO 1924-3:2005 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:29:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:29:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 1924-3:2005 iii Contents Page Forewor
10、d iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 1 4 Principle . 2 5 Apparatus 2 6 Calibration and adjustment of apparatus. 4 7 Sampling and preparation of test pieces . 4 7.1 Sampling 4 7.2 Conditioning 4 7.3 Preparation of test pieces 4 8 Procedure 4 9 Calculatio
11、n and report 5 9.1 Tensile strength 5 9.2 Tensile index . 6 9.3 Strain at break . 6 9.4 Tensile energy absorption . 6 9.5 Tensile energy absorption index. 7 9.6 Tensile stiffness 7 9.7 Tensile stiffness index . 8 9.8 Modulus of elasticity 8 10 Precision 8 10.1 Repeatability 8 10.2 Reproducibility 8
12、11 Test report . 9 Bibliography . 10 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:29:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 1924-3:2005 iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member b
13、odies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental a
14、nd non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives
15、, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies ca
16、sting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1924-3 was prepared by Technical Committee ISO/TC 6, Paper, board and pulps, Subcom
17、mittee SC 2, Test methods and quality specifications for paper and board. ISO 1924 consists of the following parts, under the general title Paper and board Determination of tensile properties: Part 2: Constant rate of elongation method 1) Part 3: Constant rate of elongation method (100 mm/min) Part
18、1: (Constant rate of loading method) was withdrawn in 2004 as it was considered obsolete. 1) In Part 2, a constant rate of elongation of 20 mm/min is used. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:29:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI v Introduction This part of ISO 1924
19、has been developed in order to specify the conditions for determining the tensile properties of paper, including tensile stiffness and tensile stiffness index, using a higher rate of elongation than specified in ISO 1924-2, which is the most commonly used part where tensile strength, stretch at brea
20、k, tensile energy absorption and modulus of elasticity are measured. In ISO 1924-2, the tensile properties are measured at a constant rate of elongation of 20 mm/min at a test span of 180 mm. For the measuring of tensile stiffness in this part of ISO 1924, a higher accuracy in the recording of elong
21、ation, compared to ISO 1924-2, is also required. This part of ISO 1924 specifies the fastest of the two methods. In addition to the properties measured in ISO 1924-2, the tensile stiffness is also measured. The tensile properties are measured at a constant rate of elongation of 100 mm/min at a test
22、span of 100 mm, and the elongation is recorded with a higher accuracy than the accuracy in ISO 1924-2. This part of ISO 1924 differs from existing standards for testing tensile properties in that the test span, i.e. the distance between the clamping lines, is 100 mm irrespective of the kind of sampl
23、e to be tested. The rate of elongation has been increased to 100 mm/min in order to reduce the testing time, thus making it possible to test a greater number of samples within a given time period. NOTE The results of tensile tests depend on the rate of elongation applied and the test span. The rate
24、dependence and the effect of test span may vary with paper grade and are different for tensile strength, strain at break, tensile energy absorption and tensile stiffness. In a study within SCAN-test, comparing the results achieved using ISO 1924-2 and this part, the tensile strength increased by 5 %
25、 to 15 % when the rate of elongation was increased from 20 mm/min (at a test span length of 180 mm) to 100 mm/min (at a test span length of 100 mm). It is not possible to predict the exact relationship between the results for any particular paper whose tensile properties are determined using ISO 192
26、4-2 and this part of ISO 1924. This relationship may only be determined by laboratory experimentation. In this part of ISO 1924, the same terminology and symbols are used as in general literature concerning physics and mechanics of materials. BS ISO 1924-3:2005 Licensed Copy: sheffieldun sheffieldun
27、, na, Mon Nov 27 08:29:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:29:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 1 Paper and board Determination of tensile properties Part 3: Constant rate of elongation method (100 mm/min) 1 Scope
28、This part of ISO 1924 specifies a method for measuring the tensile strength, strain at break, tensile energy absorption and tensile stiffness, using a testing machine operating with a constant rate of elongation (100 mm/min). This part of ISO 1924 also specifies equations for calculating the tensile
29、 index, the tensile energy absorption index, the tensile stiffness index and the modulus of elasticity. When tensile stiffness is to be determined, a greater accuracy is required in the elongation measurement than when the other tensile properties are to be determined. If the elongation is determine
30、d with the lower accuracy, the tensile stiffness value obtained is not in accordance with this part of ISO 1924. This part of ISO 1924 is applicable to all papers and boards, including papers of high extensibility, such as creped papers and extensible sack papers, but with the exception of low-densi
31、ty papers such as tissue papers and tissue products for which ISO 12625-42 is recommended. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest editio
32、n of the referenced document (including any amendments) applies. ISO 186, Paper and board Sampling to determine average quality ISO 187, Paper, board and pulps Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples ISO 534, Paper and
33、board Determination of thickness, density and specific volume ISO 536, Paper and board Determination of grammage 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 tensile strength maximum tensile force per unit width that paper and board will w
34、ithstand before breaking under the conditions defined in this standard test method 3.2 tensile index tensile strength divided by the grammage BS ISO 1924-3:2005 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:29:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 2 3.3 elongation increase in len
35、gth of a test piece 3.4 strain ratio of the elongation of a test piece to the initial test length NOTE The initial test length of the test piece is the same as the initial span between the clamping lines. 3.5 strain at break strain at the maximum tensile force 3.6 tensile energy absorption amount of
36、 energy per unit surface area (test length width) of a test piece when it is strained to the maximum tensile force 3.7 tensile energy absorption index tensile energy absorption divided by the grammage 3.8 tensile stiffness maximum slope of the curve obtained when tensile force per unit width is plot
37、ted versus strain 3.9 tensile stiffness index tensile stiffness divided by the grammage 3.10 modulus of elasticity tensile stiffness divided by the thickness 4 Principle A test piece of given dimensions is strained to break at a constant rate of elongation using a testing machine that automatically
38、records both the tensile force and the elongation. From the recorded data, the tensile strength, the strain at break, the tensile energy absorption and the tensile stiffness are calculated. 5 Apparatus 5.1 Tensile testing machine, including means of determining the force (i.e. a load-cell), the elon
39、gation and the area between the force-elongation curve and the elongation axis. The testing machine is designed to strain a test piece at a constant rate of elongation of 100 mm/min 10 mm/min, and to record both the tensile force and the elongation. NOTE 1 The true elongation rate is less than the r
40、ate of movement of the moving clamp due to the deflection of the load-cell and the testing machine. This rate difference has, however, normally a negligible effect on the strength values. The testing machine shall have two clamps for holding the test piece. Each clamp shall be designed to grip the t
41、est piece firmly, but without damage, along a straight line across the full width of the test piece (the clamping line), and have a means of adjusting the clamping force. BS ISO 1924-3:2005 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:29:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 3 N
42、OTE 2 The clamping line is the contact zone resulting from gripping the test piece between a cylindrical and a flat surface or between two cylindrical surfaces whose axes are parallel. For certain grades of paper, “line contact” clamps may not be appropriate and it may be necessary to replace them w
43、ith another type of gripping surface. Other types of clamps may be used, provided no slippage of, or damage to, the test piece occurs during the test. When the test piece is clamped, the clamping lines shall be parallel to each other within an angle of 1, see Figure 1. During the test, the angle bet
44、ween the clamping lines shall not change by more than 0,5 in the plane of the test piece. The centre-line of the test piece shall be perpendicular to the clamping lines within an angle of 1. If there is any suspicion that the test piece slips, a test with different clamping forces shall be carried o
45、ut. If the clamping force influences the strain at break, this means that the test piece may be slipping in the clamp. If the strain at break is independent of the clamping force, then no slipping in the clamps occurs. The applied tensile force shall be parallel to the test piece centre-line, in the
46、 direction of the test piece, within an angle of 1. The distance between the clamping lines (the test span) shall be 100 mm 0,5 mm. The apparatus shall have means of recording the elongation and the force as follows: Property Elongation Force Tensile strength to an accuracy of 1,0 % of the true forc
47、e Strain at break to an accuracy of 0,1 mm Tensile energy absorption to an accuracy of 0,1 mm to an accuracy of 1,0 % of the true force Tensile stiffness to an accuracy of 0,01 mm, in the range 0 to 1 mm to an accuracy of 1,0 % of the true force The elongation shall be calculated from the change in
48、distance between the clamps, or by the use of an extensometer. Clamping lines parallel to each other within an angle of 1 Centre-line of test piece perpendicular to clamping line within an angle of 1 Tensile force parallel to the test piece centre-line within an angle of 1 Figure 1 Clamping line and
49、 test piece relationship NOTE 3 If the elongation is calculated from the movement of the moving clamp, the deflection of the load-cell and of the testing machine must be taken into consideration and adjusted for. 5.2 Device for cutting test pieces to the dimensions required (see 7.3). BS ISO 1924-3:2005 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 08:29:30 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 4 6 Calibration and adjustment of apparatus The appar
链接地址:https://www.31doc.com/p-3747007.html