BS-ISO-2332-2009.pdf
《BS-ISO-2332-2009.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-2332-2009.pdf(16页珍藏版)》请在三一文库上搜索。
1、BS ISO 2332:2009 ICS 65.060.01 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Agricultural tractors and machinery Connection of implements via three- point linkage Clearance zone around implement Licensed CopyChinese University of Hong Kong, 11/04/2009 08:49,
2、 Uncontrolled Copy, (c) BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2009 BSI 2009 ISBN 978 0 580 56216 7 Amendments/corrigenda issued since publication DateComments BS ISO 2332:2009 National foreword This British Standard
3、is the UK implementation of ISO 2332:2009. It supersedes BS 6509:1984 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee AGE/6, Agricultural tractors and forestry machinery. A list of organizations represented on this committee can be obtained on request
4、 to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Licensed CopyChinese University of Hong Kong, 11/04/2009 08
5、:49, Uncontrolled Copy, (c) BSI BS ISO 2332:2009 Reference number ISO 2332:2009(E) ISO 2009 INTERNATIONAL STANDARD ISO 2332 Third edition 2009-01-15 Agricultural tractors and machinery Connection of implements via three-point linkage Clearance zone around implement Tracteurs et matriels agricoles Li
6、aisons des instruments par lattelage trois points Zone de dgagement autour de linstrument Licensed CopyChinese University of Hong Kong, 11/04/2009 08:49, Uncontrolled Copy, (c) BSI BS ISO 2332:2009 ISO 2332:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe
7、s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy.
8、The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care
9、has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no p
10、art of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale
11、 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reserved Licensed CopyChinese University of Hong Kong, 11/04/2009 08:49, Uncontrolled Copy, (c) BSI BS ISO 2332:2009 ISO 2332:2009(E) ISO 2009 Al
12、l rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a
13、 subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commissio
14、n (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical co
15、mmittees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall no
16、t be held responsible for identifying any or all such patent rights. ISO 2332 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 4, Tractors. This third edition cancels and replaces the second edition (ISO 2332:1993), which has been te
17、chnically revised. Licensed CopyChinese University of Hong Kong, 11/04/2009 08:49, Uncontrolled Copy, (c) BSI BS ISO 2332:2009 Licensed CopyChinese University of Hong Kong, 11/04/2009 08:49, Uncontrolled Copy, (c) BSI BS ISO 2332:2009 INTERNATIONAL STANDARD ISO 2332:2009(E) ISO 2009 All rights reser
18、ved 1 Agricultural tractors and machinery Connection of implements via three-point linkage Clearance zone around implement 1 Scope This International Standard specifies the clearance zone around an implement for attachment to the three- point linkage of an agricultural wheeled tractor. It is applica
19、ble to the connection of agricultural implements to three-point linkages complying with ISO 730, and also where implement couplers complying with ISO 11001-1, ISO 11001-2, ISO 11001-3 and ISO 11001-4 are used. 2 Normative references The following referenced documents are indispensable for the applic
20、ation of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 730:2009, Agricultural wheeled tractors Rear-mounted three-point linkage Categories 1N, 1, 2N, 2, 3N, 3, 4N and
21、4 ISO 11001 (all parts), Agricultural wheeled tractors and implements Three-point hitch couplers 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 implement coupler device which facilitates the connection of tractor three-point linkage to the i
22、mplement 3.2 transport pitch pitch reached by the mast when lifted to standard transport height from a position with lower links horizontal and mast vertical ISO 730:2009, 3.2.24 4 Specifications The shape and dimensions of the clearance zone around implements for attachment to a three-point linkage
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS ISO 2332 2009
链接地址:https://www.31doc.com/p-3747082.html