BS-ISO-2328-2007.pdf
《BS-ISO-2328-2007.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-2328-2007.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 2328:2007 Fork-lift trucks Hook-on type fork arms and fork arm carriages Mounting dimensions ICS 53.060 ? Licensed Copy: London South Bank University, London South Bank University, Tue Jul 03 01:06:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS ISO 2328:2007 This British St
2、andard was published under the authority of the Standards Policy and Strategy Committee on 29 June 2007 BSI 2007 ISBN 978 0 580 56170 2 National foreword This British Standard was published by BSI. It is the UK implementation of ISO 2328:2007. It supersedes BS ISO 2328:1993 which is withdrawn. The U
3、K participation in its preparation was entrusted to Technical Committee MHE/7, Industrial trucks. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are resp
4、onsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments Licensed Copy: London South Bank University, London South Bank University, Tue Jul 03 01:06:25 GMT+00:00 2007, Uncontrolled
5、 Copy, (c) BSI Reference number ISO 2328:2007(E) INTERNATIONAL STANDARD ISO 2328 Third edition 2007-05-15 Fork-lift trucks Hook-on type fork arms and fork arm carriages Mounting dimensions Chariots lvateurs fourche Bras de fourche tenons et tabliers porte-fourches Dimensions de montage BS ISO 2328:2
6、007 Licensed Copy: London South Bank University, London South Bank University, Tue Jul 03 01:06:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ii Licensed Copy: London South Bank University, London South Bank University, Tue Jul 03 01:06:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSI iii Foreword ISO
7、(the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical comm
8、ittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrote
9、chnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the memb
10、er bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifyi
11、ng any or all such patent rights. ISO 2328 was prepared by Technical Committee ISO/TC 110, Industrial trucks, Subcommittee SC 2, Safety of powered industrial trucks. This third edition cancels and replaces the second edition (ISO 2328:1993), which has been technically revised. BS ISO 2328:2007 Licen
12、sed Copy: London South Bank University, London South Bank University, Tue Jul 03 01:06:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSI blank Licensed Copy: London South Bank University, London South Bank University, Tue Jul 03 01:06:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 1 Fork-lift trucks Hook
13、-on type fork arms and fork arm carriages Mounting dimensions 1 Scope This International Standard specifies the dimensions of, and additional requirements for, fork carriers and hook-on type fork arms, to permit the interchangeability of these fork arms and/or other attachments, relative to the truc
14、k-rated capacity and fork arm type, on fork-lift trucks up to and including 10 999 kg. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of
15、 the referenced document (including any amendments) applies. ISO 2331:1974, Fork lift trucks Hook-on type fork arms Vocabulary ISO 3691:1980, Powered industrial trucks Safety code1) 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 2331 and ISO 3691 an
16、d the following apply. 4 Requirements 4.1 Dimensions The mounting dimensions of the fork arms and fork carrier for type A (short drop) and type B (long drop) fork arms (the position of the bottom hook determining the type of fork) shall be in accordance with Figures 1, 2 and 3 and Tables 1 and 2. Fo
17、rk arm location slots to the dimensions specified in Table 2 shall be provided at a suitable spacing on the fork arm carriage. In order to locate attachments, one slot shall be situated on the top edge of the carrier plate centreline. However, when an offset lower slot is provided to avoid unintenti
18、onal disengagement, then the top central slot shall be offset by dimension w (see Figure 1); this slot shall be 3 mm deeper, to facilitate the attachment and fork arm mounting. NOTE The drawings are in first and third angle projections. 1) Under revision. BS ISO 2328:2007 Licensed Copy: London South
19、 Bank University, London South Bank University, Tue Jul 03 01:06:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 2 4.2 Stops Stops shall be provided in order to prevent lateral disengagement of the fork arms from the extremities of the fork carrier. If these stops are not permanent, i.e. welded, then
20、the instruction handbook shall contain warnings that the truck is not to be used if the stops are not correctly in place. 4.3 Slot on the lower carriage If a fork arm removal/mounting slot is provided in the lower edge of a carriage, it shall be positioned as shown in Figure 3, that shown in the det
21、ailed view X being optional. If the positioning of the slots in the upper and lower fork carrier could enable the fork arm or attachment to become inadvertently disengaged from the carrier, then other means shall be provided to prevent this from occurring. Where the means of preventing unintentional
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS ISO 2328 2007
链接地址:https://www.31doc.com/p-3747418.html