《BS-EN-ISO-6360-1-2004.pdf》由会员分享,可在线阅读,更多相关《BS-EN-ISO-6360-1-2004.pdf(32页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 6360-1:2004 Incorporating corrigendum September 2007 Dentistry Number coding system for rotary instruments Part 1: General characteristics ICS 11.060.25 ? Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/
2、5910770001 Not for Resale, 08/14/2008 21:42:06 MDTNo reproduction or networking permitted without license from IHS -,-,- BS EN ISO 6360-1:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 12 May 2004 BSI 2008 ISBN 978 0 580 60299 3 Nationa
3、l foreword This British Standard is the UK implementation of EN ISO 6360-1:2004, incorporating corrigendum December 2007. It is identical with ISO 6360-1:2004, incorporating corrigendum September 2007. It supersedes BS 6828-5.1:1987 which is withdrawn. The UK participation in its preparation was ent
4、rusted by Technical Committee CH/106, Dentistry, to Subcommittee CH/106/4, Dental instruments. A list of organizations represented on this subcommittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are resp
5、onsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication DateComments 30 April 2008Implementation of ISO corrigendum September 2007 (subclause 5.5 revised) with CEN endorsement corrigendum De
6、cember 2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:42:06 MDTNo reproduction or networking permitted without license from IHS -,-,- EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM
7、 EN ISO 6360-1 April 2004 ICS 11.060.25Supersedes EN 26360-1:1990 English version Dentistry - Number coding system for rotary instruments - Part 1: General characteristics (ISO 6360-1:2004) Art dentaire - Systme de codification numrique pour instruments rotatifs - Partie 1: Caractristiques gnrales (
8、ISO 6360-1:2004) Zahnheilkunde - Nummernsystem fr rotierende Instrumente - Teil 1: Allgemeine Grundlagen (ISO 6360- 1:2004) This European Standard was approved by CEN on 1 March 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving
9、this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (
10、English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus,
11、Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN D
12、E NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 6360-1:2004 E Incorporating corrigendum December 2007 Copyright British S
13、tandards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:42:06 MDTNo reproduction or networking permitted without license from IHS -,-,- I NESO 36-06:12( 400E) Foreword This document (EN ISO 6360-1:2004) has been prep
14、ared by Technical Committee ISO/TC 106 “Dentistry“ in collaboration with Technical Committee CEN/TC 55 “Dentistry“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the l
15、atest by October 2004, and conflicting national standards shall be withdrawn at the latest by October 2004. This document supersedes EN 26360-1:1990. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europea
16、n Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Endorsement noti
17、ce The text of ISO 6360-1:2004 has been approved by CEN as EN ISO 6360-1:2004 without any modifications. _ _ BS EN ISO 6360-1:2004 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:42:06 MDTN
18、o reproduction or networking permitted without license from IHS -,-,- Reference number ISO 6360-1:2004(E) INTERNATIONAL ADNATSDR ISO 6-0631 ceSond deition 2004-04-01 Dentistry Number coding system for rotary instruments Part 1: General characteristics Art dentaire Systme de codification numrique pou
19、r instruments rotatifs Partie 1: Caractristiques gnrales Referecne unbmer OSI 1-0636:002)E(4 OSI 4002 INTERNATIONAL STANDARD ISO 6360-1 Second edition 2004-04-01 sitneDrty uNc rebmidos gnmetsy rof ratory inemurts stn :1 traP reneGaarahc lctescitsir rAed tatnire ySstmed e cfidoicaitno munrqip euour s
20、nitruemstn sfitator raPtie :1 raCactrsiqitseu grnalse BS EN ISO 6360-1:2004 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:42:06 MDTNo reproduction or networking permitted without license
21、from IHS -,-,- DPlcsid Fremia ihTs PDF file mya ctnoian emdebt dedyfepcaes. In ccacnadrow eitA hebods licnesilop gnic,y tihs file mirp eb yatnde iv roweb detu slahl ton ide ebtlnu deess teh typfecaes wihce era hml era deddebicsnede ti dna onstlalde t noeh comuptfrep reromign tide ehtin.g In wodlnida
22、ot gnihs fil,e trapise atpecc tiereht nser ehnopsiiblity fo nto ifnriigngn Aebods licnesilop gnic.y ehT ISO tneClar Secrteirata caceptl on siibality in this .aera Ai ebods a tedarmfo kra Aebod SystemI snctaropro.de teDials fo teh sfotwcudorp erats sut deo crtaee tihs PDF file cna f ebi dnuon tlarene
23、G eh Ifnler oatit evt oeh file; tP ehDc-Frtaeino marapterew stpo ereimizde fro irptni.gn Evyre cera neeb sah takne tsne oeru taht teh file is siutlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem lertait gno it is f,dnuo plsaee ifnrom ttneC ehlar Secterirata ta teh serddaig sle
24、b nevwo. ii Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:42:06 MDTNo reproduction or networking permitted without license from IHS -,-,- iii Contents Page Forewordiv Introduction v 1 Sco
25、pe1 2 Normative references .1 3 Terms and definitions.1 4 Number code .2 5 Code numbers for general characteristics.3 5.1 General.3 5.2 Materials of the working part.4 5.3 Coatings and bindings .8 5.4 Types of shanks, handles or bore diameters (of unmounted instruments) .10 5.5 Overall length 14 Ann
26、ex A (informative) Examples of identification numbers 16 Bibliography .20 BS EN ISO 6360-1:2004 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:42:06 MDTNo reproduction or networking permit
27、ted without license from IHS -,-,- iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body
28、 interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotec
29、hnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by
30、the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent righ
31、ts. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6360-1 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 4, Dental instruments. This second edition cancels and replaces the first edition (ISO 6360-1:1985), which has been technically r
32、evised. It also incorporates the Amendment ISO 6360-1:1985/Add 1:1988. ISO 6360 consists of the following parts, under the general title Dentistry Number coding system for rotary instruments: Part 1: General characteristics Part 2: Shapes Part 3: Specific characteristics of burs and cutters Part 4:
33、Specific characteristics of diamond instruments Part 6: Specific characteristics of abrasive instruments Part 7: Specific characteristics of mandrels and special instruments The following part is under preparation: Part 5: Specific characteristics of root-canal instruments BS EN ISO 6360-1:2004 Copy
34、right British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:42:06 MDTNo reproduction or networking permitted without license from IHS -,-,- v Introduction This part of ISO 6360 is one of a series of Intern
35、ational Standards relating to dental rotary instruments. A wide variety of dental rotary instruments, including root-canal instruments, is manufactured throughout the world for use by the dental profession. ISO 6360 provides a general number coding system for all types of dental rotary instruments,
36、including accessories used in connection with these rotary instruments. The benefits of this system for dentistry in its entirety will only be derived if the system is widely adopted; manufacturers of dental instruments, as well as the dental trade, are therefore requested to refer to ISO 6360 in th
37、eir catalogues. This part of ISO 6360 was prepared in response to a need by the dental trade and industry and the dental profession for a universal system of classification and designation for these instruments. It establishes a comprehensive number coding system suitable for all dental rotary instr
38、uments by use of a 15-digit code number identifying general and specific characteristics of instruments or groups of instruments. The first group of three digits identifies the materials used for the working part of instruments. The second group of three digits identifies the shanks and handles used
39、 for instruments and the overall lengths of instruments. The third group of three digits identifies the shapes of instruments. The fourth group of three digits identifies the specific characteristics for groups of instruments. The fifth group of three digits identifies the nominal diameter of the wo
40、rking part of the instruments, nominal size. The code numbers are generic code numbers. They do not provide exact product information. This information is given in the respective product standard for dental rotary instruments. For the application of the system and for the correct allocation of numbe
41、rs or their identification, it is intended that the user consult this part of ISO 6360 and ISO 6360-2 for general information, and in addition one of the subsequent parts (ISO 6360-3 to ISO 6360-7) for further information on specific characteristics of instruments or groups of instruments. For the a
42、llocation of new numbers complying with ISO 6360, an application supported by a description and a drawing should be sent to the secretariat of ISO/TC 106/SC 4, Dental instruments, which keeps updated records of all numbers currently allocated. An international group of experts will then decide on an
43、 appropriate identification number for the instrument in question, including its specific characteristics. The Secretary will inform the applicant, in due course, of the result and assist him in using the number correctly. The Secretariat of ISO/TC 106/SC 4 can be contacted at: DIN NADENT Turnplatz
44、2 75172 Pforzheim Germany BS EN ISO 6360-1:2004 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:42:06 MDTNo reproduction or networking permitted without license from IHS -,-,- blank Copyrig
45、ht British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 21:42:06 MDTNo reproduction or networking permitted without license from IHS -,-,- INTENRATIONAL TSANDADR IS-0636 O1:(4002E) 1 Dentistry Number coding
46、system for rotary instruments Part 1: General characteristics 1 Scope This part of ISO 6360 presents a number coding system for dental rotary instruments and accessories, and provides guidance with regard to its interpretation and use. This part of ISO 6360 specifies the code numbers for materials u
47、sed for the working parts of instruments, the coating and the binding of abrasives for instruments. This three-digit number forms the first group of three digits in the 15-digit overall number. This part of ISO 6360 further specifies the code numbers for shanks, handles, or bore diameter of unmounted instruments, and for the overall lengths of instruments. This three-digit number forms the second group of three (two plus one) digits in the 15-digit overall number. In Annex A several examples of complete 15-digit identification numbers are given to demonstrate the number coding system
链接地址:https://www.31doc.com/p-3747656.html