BS-ISO-15003-2006.pdf
《BS-ISO-15003-2006.pdf》由会员分享,可在线阅读,更多相关《BS-ISO-15003-2006.pdf(32页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 15003:2006 Agricultural engineering Electrical and electronic equipment Testing resistance to environmental conditions ICS 56.060.99 ? Licensed Copy: London South Bank University, London South Bank University, Sat Dec 30 06:28:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS
2、ISO 15003:2006 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 December 2006 BSI 2006 ISBN 0 580 49817 4 National foreword This British Standard was published by BSI. It is the UK implementation of ISO 15003:2006. It supersedes BS 7691:199
3、4 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee AGE/6, Agricultural tractors and forestry machinery. A list of organizations represented on AGE/6 can be obtained on request to its secretary. This publication does not purport to include all the neces
4、sary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments Licensed Copy: London South Bank University, London South Bank University, Sat
5、 Dec 30 06:28:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Reference number ISO 15003:2006(E) INTERNATIONAL STANDARD ISO 15003 First edition 2006-02-15 Agricultural engineering Electrical and electronic equipment Testing resistance to environmental conditions Gnie agricole Matriel lectrique et lect
6、ronique Essais de rsistance aux conditions environnementales BS ISO 15003:2006 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 30 06:28:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii Licensed Copy: London South Bank University, London South Bank University, Sat D
7、ec 30 06:28:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iii Contents Page Foreword iv 1 Scope 1 2 Normative references1 3 Terms and definitions .2 4 General3 4.1 General conditions for testing3 4.2 Test sequence3 4.3 Test report3 4.4 ISO 16750 compliance.4 5 Tests4 5.1 General4 5.2 Cold and dry he
8、at.4 5.3 Damp heat, steady state7 5.4 Damp heat, cyclic.7 5.5 Impact .9 5.6 Vibration .10 5.7 Corrosive atmosphere.12 5.8 Degrees of protection provided by enclosures (IP Code).12 5.9 Air pressure (altitude) .13 5.10 Chemical brush or spray.14 5.11 Solar radiation (ultraviolet).15 5.12 Readability o
9、f displays15 5.13 Electromagnetic compatibility16 5.14 Electrical environment 16 Annex A (informative) Example test report 19 Annex B (informative) Machinery/equipment codes and guidance for use of severity levels20 Bibliography25 BS ISO 15003:2006 Licensed Copy: London South Bank University, London
10、 South Bank University, Sat Dec 30 06:28:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried ou
11、t through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO co
12、llaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International
13、Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the element
14、s of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15003 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 19, Agricultural electronics. BS ISO
15、15003:2006 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 30 06:28:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 1 Agricultural engineering Electrical and electronic equipment Testing resistance to environmental conditions 1 Scope This International Standard provi
16、des design requirements and guidance for the manufacturers of electrical and electronic equipment for use in all kinds of mobile (including hand-held) agricultural machinery, forestry machinery, landscaping and gardening machinery referred to hereafter as machine(s). It gives tests for specific envi
17、ronmental conditions and defines severity levels for tests which relate to the environmental extremes that can be experienced in practical operation of the equipment. The standard is intended to be used in determining the suitability of the equipment of the these machines, for use in a specified ran
18、ge of environmental conditions. NOTE The severity levels given are general guidelines and not guaranteed worst-case exposure levels. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies.
19、 For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-1:1988, Environmental testing Part 1: General and guidance IEC 60068-2-5:1975, Basic environmental testing procedures Part 2: Tests Test Sa: Simulated solar radiation at ground level
20、IEC 60068-2-6:1995, Environmental testing Part 2: Tests Test Fc: Vibration (sinusoidal) IEC 60068-2-9: 1975, Basic environmental testing procedures Part 2: Tests Guidance for solar radiation testing IEC 60068-2-11:1981, Basic environmental testing procedures Part 2: Tests Test Ka. Salt mist IEC 6006
21、8-2-13:1983, Basic environmental testing procedures Part 2: Tests Test M: Low air pressure IEC 60068-2-14:1984, Basic environmental testing procedures Part 2: Tests Test N: Change of temperature IEC 60068-2-27:1987, Basic environmental testing procedures Part 2: Tests Test Ea and guidance: Shock IEC
22、 60068-2-30:1980, Basic environmental testing procedures Part 2: Tests Test Db and guidance: Damp heat, cyclic (12 + 12-hour cycle) IEC 60068-2-47:2005, Environmental testing Part 2: Tests Mounting of specimens to vibration, impact and similar dynamic tests BS ISO 15003:2006 Licensed Copy: London So
23、uth Bank University, London South Bank University, Sat Dec 30 06:28:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 2 IEC 60068-2-64:1993, Environmental testing Part 2: Test methods Test Fh: Vibration, broad-band random (digital control) and guidance IEC 60068-2-78:2001, Environmental testing Part 2-7
24、8: Tests Test Cab: Damp heat, steady state IEC 60512-1:2001, Connectors for electronic equipment Tests and measurements Part 1: General IEC 60529:1989, Degrees of protection provided by enclosures (IP Code) ISO 14982:1998, Agricultural and forestry machinery Electromagnetic compatibility Test method
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS ISO 15003 2006
链接地址:https://www.31doc.com/p-3747659.html